8V7319 YOKE AS Caterpillar parts
508, 916, IT18B
Rating:
Alternative (cross code) number:
CA8V7319
8V-7319
8V7319
CA8V7319
8V-7319
8V7319
Weight: 6 pounds 2 kg.
INTEGRATED TOOLCARRIER, WHEEL SKIDDER,
Compatible equipment models: 8V7319:
Information:
Remove Right Rear Cylinder Head Assembly
preparatory steps: a) remove right rear camshaft housingb) remove fuel injection lines (right side only)c) remove turbochargers 1. Loosen water ferrule clamp (2), and remove ferrule assembly.2. Remove the fuel injection pump housing-to-cylinder head bracket retaining bolts (1). 3. Remove the exhaust manifold coupling-to-elbow retaining bolts (6). Remove elbow-to-cylinder head retaining bolts (5). Remove elbow assembly.4. Remove aftercooler rear water line (4). Remove the support assembly to right cylinder head retaining bolts (3). Loosen the support assembly to left cylinder head retaining bolts. 5. Remove the two camshaft housing retaining studs (7). Remove dowel (8). 6. Remove three exhaust manifold adapter bolts (9) on Industrial engines only. Remove the cylinder head retaining bolts.7. Install three 3/8"-16NC forged eyebolts in head assembly. Attach a hoist and remove the cylinder head assembly. Weight is 300 lbs. (136 kg). Always replace the gasket between spacer plate and cylinder block before reinstalling cylinder head assembly. See REMOVE SPACER PLATES.Install Right Rear Cylinder Head Assembly
1. Clean the top surface of spacer plate and mating surface of cylinder head. Install a new head gasket and seals (1). Be sure the gasket between spacer plate and cylinder block has been replaced before installing cylinder head assembly. Refer to REMOVE AND INSTALL SPACER PLATES. 2. Attach a hoist and position the cylinder head assembly on engine. 3. Put 9S3264 Sealant Compound on the threads of the camshaft housing retaining studs (2). Install the camshaft housing retaining studs (2), and the dowel. Tighten the studs to 20 3 lb. ft. (2.77 .42 mkg). 4. Coat the threads of the cylinder head bolts and the exhaust manifold adapter bolts with 9M3710 Anti-Seize Compound. Install the cylinder head retaining bolts and washers. Tighten the bolts in following Step sequence: 1 Tighten all bolts in numerical order to 175 lb. ft. (24.2 mkg).2 Retighten all bolts in numerical order to 250 lb. ft. (34.6 mkg).3 Finally, retighten all bolts by hand in numerical order to 250 lb. ft. (34.6 mkg).4 Again tighten bolts (9) between the two heads to 250 10 lb. ft. (34.6 1.38 mkg).5. Install a new gasket, and install the exhaust manifold and adapter bolts. 6. Install the water ferrule, seal and clamp (3).7. Tighten the bolt in the clamp for the water ferrule and seal (3) to 30 5 lb. in. (34.56 5.76 cm.kg).
Do not tighten the bolt more than the specification. If the bolt is tightened more, the seal will be damaged.
8. Install the fuel injection pump housing-to-cylinder head bracket mounting bolts.9. Install the aftercooler rear water line. Install and tighten the support assembly bolts. 10. Coat the threads of the exhaust elbow coupling retaining bolts with 9M3710 Anti-Seize Compound. Install the elbow assembly (4).concluding steps: a) install right rear camshaft housingb) install fuel injection lines (right side only)c) install turbochargers
preparatory steps: a) remove right rear camshaft housingb) remove fuel injection lines (right side only)c) remove turbochargers 1. Loosen water ferrule clamp (2), and remove ferrule assembly.2. Remove the fuel injection pump housing-to-cylinder head bracket retaining bolts (1). 3. Remove the exhaust manifold coupling-to-elbow retaining bolts (6). Remove elbow-to-cylinder head retaining bolts (5). Remove elbow assembly.4. Remove aftercooler rear water line (4). Remove the support assembly to right cylinder head retaining bolts (3). Loosen the support assembly to left cylinder head retaining bolts. 5. Remove the two camshaft housing retaining studs (7). Remove dowel (8). 6. Remove three exhaust manifold adapter bolts (9) on Industrial engines only. Remove the cylinder head retaining bolts.7. Install three 3/8"-16NC forged eyebolts in head assembly. Attach a hoist and remove the cylinder head assembly. Weight is 300 lbs. (136 kg). Always replace the gasket between spacer plate and cylinder block before reinstalling cylinder head assembly. See REMOVE SPACER PLATES.Install Right Rear Cylinder Head Assembly
1. Clean the top surface of spacer plate and mating surface of cylinder head. Install a new head gasket and seals (1). Be sure the gasket between spacer plate and cylinder block has been replaced before installing cylinder head assembly. Refer to REMOVE AND INSTALL SPACER PLATES. 2. Attach a hoist and position the cylinder head assembly on engine. 3. Put 9S3264 Sealant Compound on the threads of the camshaft housing retaining studs (2). Install the camshaft housing retaining studs (2), and the dowel. Tighten the studs to 20 3 lb. ft. (2.77 .42 mkg). 4. Coat the threads of the cylinder head bolts and the exhaust manifold adapter bolts with 9M3710 Anti-Seize Compound. Install the cylinder head retaining bolts and washers. Tighten the bolts in following Step sequence: 1 Tighten all bolts in numerical order to 175 lb. ft. (24.2 mkg).2 Retighten all bolts in numerical order to 250 lb. ft. (34.6 mkg).3 Finally, retighten all bolts by hand in numerical order to 250 lb. ft. (34.6 mkg).4 Again tighten bolts (9) between the two heads to 250 10 lb. ft. (34.6 1.38 mkg).5. Install a new gasket, and install the exhaust manifold and adapter bolts. 6. Install the water ferrule, seal and clamp (3).7. Tighten the bolt in the clamp for the water ferrule and seal (3) to 30 5 lb. in. (34.56 5.76 cm.kg).
Do not tighten the bolt more than the specification. If the bolt is tightened more, the seal will be damaged.
8. Install the fuel injection pump housing-to-cylinder head bracket mounting bolts.9. Install the aftercooler rear water line. Install and tighten the support assembly bolts. 10. Coat the threads of the exhaust elbow coupling retaining bolts with 9M3710 Anti-Seize Compound. Install the elbow assembly (4).concluding steps: a) install right rear camshaft housingb) install fuel injection lines (right side only)c) install turbochargers
Caterpillar parts catalog:
Parts yoke Caterpillar catalog:
8V7245
YOKE AS
916, IT18B
916, IT18B
3T2256
YOKE AS
916, IT18B
916, IT18B
3T0017
YOKE-BRAKE FLANGE
916, IT18B
916, IT18B
9C3523
YOKE AS
IT18B
IT18B
5V3733
YOKE
916, 918F, IT18B
916, 918F, IT18B
5V3735
YOKE AS
916, 918F, IT18B, IT18F
916, 918F, IT18B, IT18F
8V4101
YOKE
508, PF-290B, PS-360B
508, PF-290B, PS-360B
9W1136
YOKE
508
508
9W1132
YOKE AS
508
508
6W4022
YOKE
508
508
9W1158
YOKE-PTO
508
508
9C8338
YOKE AS
508
508
8V7245
YOKE AS
916, IT18B
916, IT18B
5T9050
YOKE AS
631E, 633D, 637D, 637E
631E, 633D, 637D, 637E
9V0433
YOKE ASSEM.
920, 930
920, 930
5V7581
YOKE AS
926, 936, G936, IT18F, IT28, IT28B
926, 936, G936, IT18F, IT28, IT28B
5V7566
YOKE AS
926, G936, IT28
926, G936, IT28
5V8975
YOKE
936, G936
936, G936
3T4953
YOKE
930R
930R
2Y8188
YOKE
631E
631E
7V3783
YOKE
926, IT28, IT28B
926, IT28, IT28B
7V3782
YOKE AS
926, IT28
926, IT28
3T0017
YOKE-BRAKE FLANGE
916, IT18B
916, IT18B
3T2256
YOKE AS
916, IT18B
916, IT18B