AVSPARE.COM
parts catalog

SEAL KIT-H- 1326783 - Caterpillar



1326783 SEAL KIT-H- Caterpillar parts SEAL
Rating:
76
Alternative (cross code) number:
CA1326783
132-6783
1326783
Caterpillar 1326783 SEAL KIT-H-

Buy SEAL KIT-H- 1326783 Caterpillar genuine, new aftermarket tractor parts with delivery

You can buy parts: .

$203.50

21 Jan 2020
Hydraulic Seal Kit - Lift Cylinder, New, Caterpillar, 1326783
Parts Categories Construction & Industrial Caterpillar D11 Hydraulics || All Brand new & rebuilt items comes with 1 year warranty.
$5.88

21 Jan 2020
RELAY - 12 VOLT FOR HYSTER: 1326783
HYSTER || All Brand new & rebuilt items comes with 1 year warranty. || RELAY - 12 VOLT. Category: HYSTER FORKLIFT PARTS. This part can also be found under the following part numbers: HY1326783 1326783  HYSTER 1326783  HYSTER1326783 1326783     . All Brand new & rebuilt items comes with 1 year warranty.
$203.50

21 Jan 2020
Hydraulic Seal Kit - Lift Cylinder, New, Caterpillar, 1326783
Parts Categories Construction & Industrial Caterpillar D11 Hydraulics || All Brand new & rebuilt items comes with 1 year warranty.
  For full view, you need register

Information:

This procedure is only applicable to engines with a hydraulic driven fan.Use this procedure to troubleshoot the electrical system if a problem is suspected with the engine fan control solenoids. Use this procedure if one of the diagnostic codes in Table 1 is active.
Table 1
Diagnostic Codes for Cooling Fan Control
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
4212-5 291-5 Engine Cooling Fan Solenoid : Current Below Normal The Electronic Control Module (ECM) detects an open circuit in the circuit for the engine fan control solenoid.
The ECM sends minimum current to the fan control solenoid. The code is logged.
4212-6 291-6 Engine Cooling Fan Solenoid : Current Above Normal The ECM detects a short circuit to ground in the circuit for the engine fan control solenoid.
The ECM sends minimum current to the fan control solenoid. The code is logged.
- 1076-5 Engine Cooling Fan Bypass Solenoid : Current Below Normal The Electronic Control Module (ECM) detects an open circuit in the circuit for the engine cooling fan bypass solenoid.
The ECM sends minimum current to the fan control solenoid. The code is logged.
- 1076-6 Engine Cooling Fan Bypass Solenoid : Current Above Normal The ECM detects a short circuit to ground in the circuit for the engine cooling fan bypass solenoid.
The ECM sends minimum current to the fan bypass solenoid. The code is logged. The ECM monitors engine coolant temperature, intake manifold air temperature, and hydraulic oil temperature. The ECM monitors the sensors in order to determine the correct speed for the engine cooling fan.The ECM controls the speed of the fan by controlling the current to the engine fan control solenoid. The engine fan control solenoid controls the amount of pressure to the fan motor by allowing oil to bypass the fan motor. The fan pump drives the fan. When the ECM outputs minimum current to the engine fan control solenoid, less oil is bypassed. The fan motor will now drive the fan at a higher rpm. When the ECM outputs maximum current to the engine fan control solenoid, more oil is bypassed. The fan motor will now drive the fan at a lower rpm.If the ECM detects a system fault, the ECM provides minimum current to the solenoid. Minimum current ensures a maximum fan speed while the fault condition exists.An override is available in the electronic service tool. The override allows the fan to be manually changed from the minimum to the maximum rpm.The cooling fan bypass solenoid prevents operation of the fan when the engine is cold. When the engine has warmed up, the solenoid will open the valve to allow hydraulic pressure to flow to the fan motor.During the following procedure, refer to the electrical schematic for the application.Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Active Diagnostic Codes
A. Remove the electrical power from the ECM.
B. Verify that the solenoid connectors are free of debris and connected securely.
C. Connect the electronic service tool to the diagnostic


Parts seal Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.