AVSPARE.COM
parts catalog

PLATE 2559638 - Caterpillar



2559638 PLATE Caterpillar parts 325C PLATE
Rating:
26
Alternative (cross code) number:
CA2559638
255-9638
2559638
Caterpillar 2559638 PLATE
Weight: 4 pounds 1 kg.

Buy PLATE 2559638 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 2559638:

EXCAVATOR  325C   Caterpillar
Number on catalog scheme: 5
 
  For full view, you need register

Information:


Illustration 1 g03841576This diagnostic code is recorded when the VIMSTM Main ECM does not receive expected information from the Engine ECM at the correct rate. The information is transmitted through the Cat® data-link.System Response:This failure results in events that are logged against the Engine ECM that cannot be explained. The VIMS Main ECM cannot communicate with the Engine ECM or the Engine ECM appears to communicate intermittently.Test Step 1. VERIFY THE HARDWARE AND THE SOFTWARE PART NUMBERS
Verify that the following information is correct:
The part number of the software for each ECM
The part number for each ECMNote: Consult your Caterpillar dealer for the correct part numbers of the software.Expected Result:All of the part numbers are correct.Results:
YES - All of the part numbers are correct. Proceed to Test Step 2
NO - One or more of the part numbers are not correct.Repair: Replace the incorrect ECM with an ECM that has the correct part number. Install the correct software. Refer to Troubleshooting, Testing and Adjusting, "Electronic Control Module (ECM) - Replace" and Troubleshooting, Testing and Adjusting, "Electronic Control Module (ECM) - Flash Program"STOPTest Step 2. INSPECT THE HARNESS CONNECTIONS
Turn the disconnect switch and key start switch to the OFF position.
Inspect all harness connections that are related to the CAT Data Link. Make sure that the connectors are clean and tight
Check the connectors for proper mating. Ensure that all the seals are present and in place.
Check the harness for signs of damage or abrasion.
Check the wires at the connector. Ensure that the wires are secured tightly into the connector. Take care not to pull the wire out of the connector.
Check the exposed wires at the connectors for nicks or signs of abrasion.
Check for moisture inside the connector.
Check the connectors for dirty contacts or corroded contacts.
Check each pin and each socket of the machine harness connectors. Ensure that the contacts are properly installed. The contacts should mate correctly when the two pieces of the connector are placed together. Expected Result:The machine harness connectors are tight and free of corrosion.Results:
YES - The machine harness connectors are tight and free of corrosion. Proceed to Test Step 3
NO - The machine harness connectors are in need of repair.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK FOR A SHORT CIRCUIT IN THE HARNESS
The disconnect switch and key start switch remain in the OFF position.
Disconnect the machine harness connectors from all ECMs that use the CAT Data Link.
At the machine harness connector for the VIMS module, measure the resistance between connector contact J1-50 (wire F711-GN(Green)) and all of the contacts that are used in the machine harness connector for the ECM. Perform the same measurements for J1-34 (wire F712-GY(Grey)). Expected Result:Each resistance measurement is greater than 5 ohms.Results:
YES - Each of the resistance measurements are greater than 5 ohms. The harness circuit resistance is correct. Proceed to Test Step 4
NO - One or more of the resistance measurements are less than 5 ohms. The machine harness has failed.Repair: There is a short between contact

Caterpillar parts catalog:

Caterpillar parts catalog
325 CR SUPPLEMENT FOR TRACK-TYPE EXCAVATOR /COMPACT RADIUS HYDRA/ BKW00326-UP (MACHINE)
325C CR TRACK-TYPE EXCAVATOR /COMPACT RADIUS HYDRA/ BKW00343-UP (MACHINE)
325C L CR TRACK-TYPE EXCAVATOR /COMPACT RADIUS HYDRA/ BKW00328-UP (MACHINE)
325 CR SUPPLEMENT FOR TRACK-TYPE EXCAVATOR /COMPACT RADIUS HYDRA/ BKW00326-UP (MACHINE)
325C CR TRACK-TYPE EXCAVATOR /COMPACT RADIUS HYDRA/ BKW00343-UP (MACHINE)
325C L CR TRACK-TYPE EXCAVATOR /COMPACT RADIUS HYDRA/ BKW00328-UP (MACHINE)


Parts plate Caterpillar catalog:

7C8634 PLATE
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 1290T, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160H, 160H ES, 160H NA, 160K, 163H NA, 214B, 224B, ...
7C6672 PLATE-CLAMP
120H, 120H ES, 120H NA, 12H, 135H, 135H NA, 214B, 30/30, 3114, 3116, 3126, 3126B, 3126E, 3176, 3176B, 320 L, 320B, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, ...
5P9891 PLATE-WARNING
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 307, 307B, 307D, 307E, 308E, 311, 311B, 311C, 312, 312B, 312B L, 312C L, 313B, 314C, 315, 315B, 315B FM L, 315C, 317, 318B, 318C, 319C, 320 L, 320B, 3...
2531346 PLATE-WARNING
1290T, 1390, 2491, 2590, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311D LRR, 311F LRR, 312C, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR...
1673862 PLATE-RETAINER
325C, 328D LCR, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 993K
1884167 PLATE
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D M...
2042677 PLATE-VALVE
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D M...
1132824 PLATE AS
1090, 1190, 1190T, 1390, 2290, 2390, 2391, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322B L, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D FM, 324D FM LL, 325, 325 L, 325B, 32...
0940579 PLATE
320B, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322B L, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325C FM, 325D, 32...
0940578 PLATE
320B, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322B L, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325C FM, 325D, 32...
1348951 PLATE
115, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330, 330 L, 330B, 330B L, 330C, 330C L, 330D, 330D L, 330...
1673865 PLATE-SEPARATOR
325C, 328D LCR, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.