AVSPARE.COM
parts catalog

ROD 2559649 - Caterpillar



2559649 ROD Caterpillar parts 314C ROD
Rating:
21
Alternative (cross code) number:
CA2559649
255-9649
2559649
Caterpillar 2559649 ROD

Buy ROD 2559649 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 2559649:

EXCAVATOR  314C   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:

Illustration 1(1) Bolt(2) Washer(3) Air inlet cover
Remove bolt (1) and the washer (2) from the airinlet cover (3). Discard the bolt (1) and the washer (2).
Disconnect the electrical connector of the injectionactuation pressure control valve (7). Remove the injection actuation pressurecontrol valve (7) from the pump. Retain the injection actuation pressurecontrol valve (7) for the reinstallation.
Modifications to the tools may needto be made in order to reduce interference with engine components. Illustration 2 (Modified 2P5494 crowfoot wrench)
Remove the hose assembly (5), the connector (8),and the elbow (6). Discard these parts.
Illustration 3(4) HEUI pump(5) Flexible oil line(6) Elbow(7) Injection actuation pressure control valve(8) Connector
Installation of 2400716 Tube Kit
Illustration 4(4) HEUI pump(7) Injection actuation pressure control valve(9) Connector(10) Clip(11) Washer(12) Bolt(13) Spacer(14) Tube assembly(15) O-ring(16) O-ring(17) Elbow
Illustration 5(7) Injection actuation pressure control valve(9) Connector(15) O-ring(16) O-ring(17) Elbow
Apply a light coat of oil to the O-rings (15)and (16) during installation. Install the O-ring (15) on the connector(9). Install the O-ring (16) on the connector (9). Thread the connector(9) into the port on the cylinder head by hand. Tighten to 48 + 5 Nm (35+ 4 lb ft).
Apply a light coat of oil to the O-rings (15)and (16) during installation. Install the O-ring (15) on the elbow (17).Install the O-ring (16) on the elbow (17).
Back off the jam nut on the elbow (17) to thetop of the threads on the elbow assembly (17). Push the washer tightlyagainst the jam nut. Check that the washer is as tight as possible. Threadthe elbow assembly (17) into the port of the HEUI pump (4). Hand tightenthe elbow (17) into the port of the HEUI pump until the washer is tightagainst the HEUI pump (4). Unscrew the elbow assembly (17) no more thanone complete turn to 40 degrees.
Align the tube assembly (14) with the connector(9) and the elbow (17). Loosely thread each end of the tube assembly (14)onto the connector (9) and the elbow (17). Position the elbow (17) in orderto not create stress in the tube assembly (14).
Attach the clip (10) to the tube assembly (14).The flat side of the clip (10) must be toward the air inlet cover. Placethe washer (11) onto the bolt (12). Insert the bolt (12) through the clip(10) and the spacer (13).
Insert the bolt (12) through the air inlet cover(3).
Thread the bolt (12) into the cylinder head.
Hand tighten the bolt (12).
Hand tighten both connections on the tube assembly(14).
Ensure that there is no stress on thetube assembly (14) from any components or fittings.
Use a wrench to prevent the elbow assembly (17)from turning. Tighten the bottom tube fitting to the elbow assembly (17)to 40 + 4 Nm (29.5 + 3 lb ft).
Tighten the top tube fitting to the connector(9) to 40 + 4 Nm (29.5 + 3 lb ft).
Use a wrench to prevent the elbow assembly (17)from turning. Tighten the jam nut of the elbow assembly (17) to 24 + 2Nm (18 + 1.5 lb ft).
Tighten the bolt (12) to 28 +/- 7 Nm (21 +/- 5lb ft).
Illustration 6(7) Injection actuation pressure

Caterpillar parts catalog:

Caterpillar parts catalog
314C CR, 314C LCR SUPPLEMENT FOR EXCAVATORS /CIRCUIT POWER OFFSET/ KJA00001-UP (MACHINE)


Parts rod Caterpillar catalog:

8C3111 ROD END
307, 308E SR, 312, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 317, 320 L, 322, 322 FM L, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, 350, 350 L, 375, 375 L, 5080, 5130, 5130B, 5230, 5230B, 525B, 5...
0933094 ROD
307, 307B, 307C, 308C, 311B, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312E, 312E L, 313B, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318E L, 319D L, 319D LN, 321C, ...
1184086 ROD
307C, 308C, 311, 311B, 311C, 311D LRR, 311F LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E ...
5I7668 ROD AS
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
1848874 ROD
311D LRR, 311F LRR, 312C, 312C L, 314C, 314D CR, 314D LCR, 320D FM RR, 320D LRR, 320D RR, 321D LCR, D6N, D6N LGP
1792980 ROD
311C, 312C L, 314C
1733356 ROD AS
312C, 312C L, 314C
1988176 ROD AS
303.5C, 303.5D, 303.5E, 303C CR, 304, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 311D LRR, 311F LRR, 312D, 312D L, 312D2...
2394415 ROD
311C, 312C L, 314C
2299181 ROD
308C, 308D, 314C, 314D CR, 314D LCR, 321C, 321D LCR, 325C, 328D LCR
2299182 ROD
308C, 308D, 314C, 314D CR, 314D LCR, 321C, 321D LCR, 325C, 328D LCR
1961457 ROD
308C, 308D, 308E CR, 308E SR, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 321C, 321D LCR, 325C, 328D LCR
1067756 ROD AS.
318B, 320 L, 320B, 325B L, 330B L, 345B L
5I3575 ROD ASSEM.
311B, 320 L, 320B, 325, 325 LN, 325B, 350, 375
2206337 ROD AS
315C, 315D L, D3G, D4G, D5G
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.