AVSPARE.COM
parts catalog

LINES GP-CYL 2559668 - Caterpillar



2559668 LINES GP-CYL Caterpillar parts LINES
Rating:
86
Alternative (cross code) number:
CA2559668
255-9668
2559668
Caterpillar 2559668 LINES GP-CYL

Buy LINES GP-CYL 2559668 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

1. Open the right access door. 2. Loosen the cylinder retaining clamp. Unscrew the empty ether cylinder.3. Remove the used gasket. Install the new gasket provided with each new cylinder. 4. Install the new cylinder. Tighten the cylinder hand tight. Refasten the cylinder clamp securely.5. Close the access door.Cab Air Filters
Clean the Air Filters
When using pressure air for cleaning, wear a face shield and protective clothing.Use a maximum air pressure of 205 kPa (30 psi) for cleaning purposes.
Recirculation Filter
1. Loosen the two bolts and remove the cover. 2. Remove the recirculation filter element. Wash it in clean water and household detergent. Rinse thoroughly with clear water, and blow dry with pressure air.3. Install the cleaned filter element. Replace the cover and tighten the bolts.Fresh Air Filters
1. Open the left access door. 2. Unlatch and remove the access cover. 3. Loosen the wing nuts.4. Remove the filters. Clean the elements (see "Cleaning Elements"). Clean the housing thoroughly. 5. Install the filters. Tighten the wing nuts. Install the access cover and secure the latch.6. Close the access door.Cleaning Elements
Elements can be cleaned with air pressure or water pressure.
Do not clean the elements by bumping or tapping them.Inspect the elements after cleaning. Do not use an element with damaged pleats, gaskets or seals.When cleaning with water pressure, use 280 kPa (40 psi) maximum pressure to prevent element damage.
Air Pressure - 205 kPa (30 psi) Maximum
1. Direct air along pleats inside and outside of element.2. Inspect the element after cleaning.Water Pressure - 280 kPa (40 psi) Maximum
1. Direct the water along the inside and outside of the pleats.2. Air dry and inspect the element.Bucket Teeth
Change the Bucket Teeth
Pins, when struck with force, can fly out and cause injury to nearby people.Make sure the area is clear of people when driving retainer pins.To avoid injury to your eyes, wear protective glasses when striking a pin.
To prevent mounting surface damage, replace bucket teeth when worn close to the adapter.
1. Start the engine.2. Raise the bucket, place blocks under the bucket. Lower the bucket on to the blocks. Shut the engine off. 3. Drive the pin out from the side that the spring is installed. Remove the bucket tooth, pin, and spring. 4. Clean the adapter, pin and spring. Install the spring in the adapter. 5. Install the new bucket tooth. Install the pin through the side opposite from that in which the spring is installed.6. Start the engine. Raise the bucket, remove the blocks and lower the bucket.7. Shut off the engine.Ripper Tips
Change the Ripper Tips
Pins, when struck with force, can fly out and cause injury to nearby people.Make sure the area is clear of people when driving retainer pins.To avoid injury to your eyes, wear protective glasses when striking a pin.
To prevent shank damage, replace ripper teeth when worn close to the shank.
1. Start the engine. Raise the ripper. Place blocks under the ripper frame. Lower the ripper on to the blocks. Shut the engine off. 2. Drive the pin out from


Parts lines Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.