AVSPARE.COM
parts catalog

TUBE AS 2559672 - Caterpillar



2559672 TUBE AS Caterpillar parts TUBE
Rating:
26
Alternative (cross code) number:
CA2559672
255-9672
2559672
Caterpillar 2559672 TUBE AS

Buy TUBE AS 2559672 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

(22)Fuel Filters
Primary Filter Element
Wash Primary - Change Secondary
When using pressure air for cleaning, wear a face shield and protective clothing.Use a maximum air pressure of 205 kPa (30 psi) for cleaning purposes.
1. Open the left side access door. 2. Loosen the bolt in the top of the primary filter element housing. 3. Remove the case and element from the filter housing.4. Wash the element and case in clean, nonflammable solvent.5. Check the seal in the housing. Replace the seal if it is damaged. 6. Install the element into the case. Install the case and filter on the filter housing. Tighten the retaining bolt to a torque of 24 4 N m (18 3 lb. ft.).Secondary Filter
1. Remove and discard the secondary filter element.2. Make certain all of the used element seal is removed from the filter base.3. Coat the seal of the new element with clean diesel fuel. 4. Install the filter by hand. When the seal contacts the base, tighten 3/4 turn more.There are rotation index marks, 90° apart on the filter, as a guide for proper tightening.5. Prime the fuel system. (See next topic.)Priming Fuel System
1. Move the governor control lever to the SHUT-OFF position. 2. Turn to unlock the priming pump plunger, and pull it out. Operate the pump to fill the new filter with fuel. Continue pumping until resistance is felt, indicating the system is full. Push in the priming pump plunger, and turn it to lock it. 3. Start the engine. If the engine does not start, the fuel system has air trapped in the fuel lines to the engine.
Using only one wrench to loosen the fuel lines at the injector can cause damage to the injector.
4. Loosen all fuel injection tubing line nuts at the cylinder head of the engine.5. Use two wrenches as shown above. Do not allow the injector to move, or injector damage could result. 6. Move the governor control lever to the LOW IDLE position. 7. Turn the START/RUN switch to START. Crank the engine until fuel flows free of air bubbles, from all fuel lines.8. Shut OFF the engine.9. Use two wrenches and retighten the fuel line nuts to a torque of 40 7 N m (30 5 lb. ft.).10. Close the access door.(23)Track Pivot Shaft
Look at the Oil Level1. Remove the oil fill plug.2. If necessary, add oil to bring level to 19 mm (.75 in) below the bottom of the fill plug opening. 3. Install the fill plug.4. Repeat the above procedure on the other side of the machine.(24)Engine Crankcase Breather
Wash and Oil
Use all cleaning solutions with care.
1. Open the left side access door. 2. Remove the clamps (2) and hose (3). Loosen the bolt (1).3. Remove the breather. Wash it in clean, nonflammable solvent. Inspect the gasket and replace if necessary.4. Install the breather. Tighten the bolt only finger tight so it can be turned, if necessary. Install the hose and clamps. Tighten the bolt securely.


Parts tube Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.