AVSPARE.COM
parts catalog

LINES GP- 2559844 - Caterpillar



2559844 LINES GP- Caterpillar parts LINES
Rating:
46
Alternative (cross code) number:
CA2559844
255-9844
2559844
Caterpillar 2559844 LINES GP-

Buy LINES GP- 2559844 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

2. Remove the case and the element from the filter base. 3. Remove the filter element from the case.
When using pressure air, wear a protective face shield and protective clothing. The maximum air pressure at the nozzle must be less than 205 kPa (30 psi) for cleaning purposes.Use all cleaning solutions with care.
4. Wash the element in a clean, nonflammable solvent. Shake or blow all parts dry. 5. Clean the case with a cloth or a stiff fiber brush. 6. Insert the element in the case. 7. Install the case and element on the base. Tighten the retaining bolt.8. Start the engine and check for leaks.Final Filter
1. Remove the fuel filter with a strap-type wrench. 2. Clean the filter base gasket surface. Remove all of the old gasket. 3. Lubricate the new filter gasket with clean diesel fuel. 4. Install the new filter element by hand. When the gasket contacts the base, tighten 1/2 turn more.
Do not overtighten the filter element.
5. Prime the fuel system (see the next topic).6. Start the engine and check for leaks.Priming the Fuel System
1. Unlock the priming pump plunger. 2. Operate the plunger until a resistance is felt.3. Close the pump and lock the plunger.4. Start the engine and inspect for leaks.Transmission
Change Filter
Hot oil and components can cause injury. Do not allow hot oil or components to contact the skin.When using pressure air, wear a protective face shield and protective clothing. The maximum air pressure must be below 205 kPa (30 psi) for cleaning purposes.Use all cleaning solutions with care.
The machine must be level and the oil warm. Lower the bucket with slight down pressure.Apply the parking brake. Stop the engine. 1. Remove the cover on the left rear side of the operator's platform. 2. Use a strap-type wrench or a cross bar to remove the filter housing. 3. Remove and discard the used element. 4. Clean the filter housing with a clean, nonflammable solvent. 5. Clean the housing base.6. Insert a new element into the filter housing. 7. Inspect the filter housing seal. Replace the seal, if it is damaged.8. Install the filter housing into the housing base.
Be careful not to damage the thread on the filter housing or filter base, when installing the filter housing. Do not overtighten.
9. Start the engine. Apply the service brake. Use the right brake pedal only. 10. Slowly operate the transmission controls to circulate the oil.11. Lock the transmission control lever in NEUTRAL. Inspect for leaks. 12. Measure the oil level.13. Add oil, if necessary, to bring the oil level between the ADD and FULL marks on the "Engine at Low Idle" side of the dipstick.14. Install cover.Fuel Tank Cap and Fill Screen
Clean Cap and Screen
1. Remove and disassemble the fuel tank cap.
When using pressure air wear a protective face shield and protective clothing. The maximum air pressure must be below 205 kPa (30 psi) for cleaning purposes.Use all cleaning solutions with care.
2. Wash all cap parts in a clean, nonflammable solvent.3. Oil the element slightly.


Parts lines Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.