AVSPARE.COM
parts catalog

BOLT 2559978 - Caterpillar



2559978 BOLT Caterpillar parts BOLT
Rating:
36
Alternative (cross code) number:
CA2559978
255-9978
2559978
Caterpillar 2559978 BOLT

Buy BOLT 2559978 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

Transmission Filter
Change the Filter Element
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.
1. Remove the floor plate. 2. Remove the filter element cover assembly.3. Remove and discard the filter element.4. Clean the housing with a clean cloth.5. Inspect the cover seal. Replace if damaged.6. Install the new element and cover.7. Start the engine. 8. Maintain the oil level to the FULL mark on the dipstick. Add the oil through fill tube if necessary.9. Stop the engine and install the floor plate.Universal Joints
Lubricate Fittings
Lubricate 2 fittings.Power Take-Off U-Joints (If Equipped)
Lubricate Fittings
Lubricate 2 fittings.Power Take-Off Bearings (If Equipped)
Lubricate Fitting
Lubricate 1 fittings.Hydraulic System Filter
Change the Filter Element
At operating temperature, the hydraulic tank is hot and under pressure.Hot oil can cause burns.Remove the fill cap only when the engine is stopped, and the cap is cool enough to touch with your bare hand. Remove the fill cap slowly to relieve pressure.
1. Remove the oil filler cap to relieve the tank pressure. 2. Loosen the retaining bolt.3. Remove the cover and filter.4. Discard the filter element.5. Inspect the condition of the "O" ring seal. Replace if necessary.6. Install a new filter element and cover. Tighten the cover retaining bolt to 58 5 N m (40 4 ft lb). Install the fill cap. 7. Maintain the hydraulic oil to the FULL mark in sight gauge.Winch Filter (If Equipped)
Change Filter - Wash Strainer
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.
1. Remove the cover and gasket. 2. Remove the filter element housing with a wrench.3. Remove the filter element from the housing.4. Clean the housing with a clean cloth.5. Replace the seal if damaged. Lubricate the seals with clean winch oil.6. Install a new filter element into the housing.7. Tighten the housing to 27 4 N m (20 3 lb ft).8. Install the cover and gasket.Clean the Suction Screen
1. Remove the cover. 2. Clean in nonflammable solvent.3. Install the clean suction screen.4. Inspect the cover seal and replace if damaged.5. Install the cover.Fuel Filter
Change Primary Filter Element
Pressure air can cause personal injury.When using pressure air for cleaning, wear a protective face shield, protective clothing and protective shoes.The maximum air pressure must be below 205 kPa (30 psi) for cleaning purposes.Use all cleaning solutions with care.Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire.Turn the disconnect switch OFF or disconnect the battery when changing fuel filters.
Do not fill fuel filter with fuel before installing them. Contaminated fuel will cause accelerated wear to fuel system parts.
1. Shut off the fuel supply valve located under the fuel tank. 2. Remove right front side panel to gain access to fuel filters. 3. Remove and discard the filter element.4. Clean the filter element mounting base. Be sure all of the old seal is removed.5. Coat the seal of the new filter element with clean diesel fuel.6. Install the new filter element by hand.


Parts bolt Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.