AVSPARE.COM
parts catalog

GASKET 2559988 - Caterpillar



2559988 GASKET Caterpillar parts 901C, 902C, 903C GASKET
Rating:
18
Alternative (cross code) number:
CA2559988
255-9988
2559988
Caterpillar 2559988 GASKET

Buy GASKET 2559988 Caterpillar genuine, new aftermarket tractor parts with delivery
COMPACT WHEEL LOADER,

Compatible equipment models: 2559988:

COMPACT WHEEL LOADER  901C   902C   903C   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:

Probable Causes
ECM Personality module
Electrical power to ECM
Remote shutdown switch
Starting motor solenoid or starting circuit
Engine speed/timing sensors
Electrical connections to the electronic unit injector
Fuel supply
Combustion problemRecommended Actions
ECM Personality module
If a new ECM has been installed on the engine, the Engine will not start. Also, the ECM will not communicate with the ET until the correct personality module has been flashed into the ECM.
Verify that the following diagnostic is not active.
CID 253-FMI 02, SPN 234-FMI 02, Flash Code 56, Personality Module mismatchIf the code is active, access the "Winflash" and flash the correct version of the software.Electrical power to ECM
Turn the keyswitch OFF.
Check the positive battery and negative battery connections to the ECM.
Perform a pull test on positive battery wires and negative battery wires.
Check the negative battery connection on the Ground Stud.
Turn the keyswitch ON.
The warning lamps should come on for 2 - 4 seconds.If the warning lamp comes on for 2 to 4 seconds, continue to follow this procedure.If the warning lamp does not come on for 2 to 4 seconds, refer to Troubleshooting, "Electrical Power Supply Circuit - Test".Remote shutdown switch
Access the ET screen that displays the Remote Shutdown Switch status. The Remote Shutdown Switch status on the ET is called "User Shutdown".
Table 1
"User Shutdown Status"     Switch Status     Measured Voltage at P61:27    
ON     Negative battery     <0.9 VDC    
OFF     Open Circuit     >10 VDC    If the voltage is not in the proper range, refer to Troubleshooting, "Remote Shutdown Switch Circuit - Test".Starting Motor Solenoid or Starting Circuit
Test the operation of the starting motor solenoid.
Check the engine wiring to the starting motor solenoid.
Test the operation of the starting motor.
Inspect the starter motor pinion and the flywheel ring gear for damage.Engine speed/timing sensors
Observe the engine speed on the ET while the engine is being cranked.This situation may require a direct hookup to the batteries in order to power the ET while the engine is cranking. Refer to illustration 1 for the wiring diagram.
Illustration 1 g00748412
If the engine is cranking and the ET displays 0 rpm, a problem exists in the circuits for the engine speed/timing sensors. The problem is in the circuit for the engine speed/timing sensor (crankshaft) or the circuit for the engine speed/timing sensor (camshaft). Refer to Troubleshooting, "Engine Speed/Timing Sensor Circuit - Test".If an engine speed is present, check the sensor installation. If the sensor is not properly installed, the ECM may read engine speed, but the ECM cannot determine the tooth pattern. The ability for the ECM to read the tooth pattern is necessary to determine the cylinder position. Engine speed is present when engine speed is greater than 50 rpm. Refer to Troubleshooting, "Engine Speed/Timing Sensor Circuit - Test".Electrical connections to the electronic unit injector
Ensure that the electronic unit injector connector (J300/P300) is fully connected and ensure that the electronic unit injector connector (J300/P300) is free of corrosion.
Check for logged

Caterpillar parts catalog:

Caterpillar parts catalog
901C Compact Wheel Loader W4T00001-UP (MACHINE) POWERED BY C1.8 Engine
902C Compact Wheel Loader W5T00001-UP (MACHINE) POWERED BY C2.4 Engine
903C Compact Wheel Loader W6T00001-UP (MACHINE) POWERED BY C2.4 Engine


Parts gasket Caterpillar catalog:

1U8846 GASKET-LIQUID
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120M, 120M 2, 1290T, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140M, 140M 2, 143H, 14H, 14M, 160H,...
2521863 GASKET
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 414E, 416E, 416F, 420E, 420F, 422E, 422F, 424B, 428E, 428F, 430E, 430F, 432E, ...
3830460 GASKET
304E, 305.5E, 305E, 902C, 903C
3830461 GASKET
304E, 305.5E, 305E, 902C, 903C
3830498 GASKET
304E, 305.5E, 305E, 902C, 903C
4394170 GASKET
303E CR, 902C, 903C
6S6514 GASKET
901C, 902C, 903C, 910, 910E, 910G, 914G, 924F, 931B, 933, 933C, 938F, 938G II, 939, 939C, 950F, 950G, 950H, 960F, 966F, 966G, 966G II, 966H, 970F, 980G, D3, D3B, D3C II, D3C III, D4C III, D5C III, D5M...
3047168 GASKET
901C, 902C, 903C, 914G, 924K, 930K, 938K, 950 GC, 950H, IT14G2
2578048 GASKET
901C, 902C, 903C, 904B, 904H
3171281 GASKET
901C, 902C, 903C, 904B, 904H
4383502 GASKET
901C, 902C, 903C
2578049 GASKET
901C, 902C, 903C
2578049 GASKET
901C, 902C, 903C
4383502 GASKET
901C, 902C, 903C
2S0303 GASKET
621, 623, 980
3J4447 GASKET- RELAY EMERGENCY VALVE TO RESERVOIR
621, 621B, 627, 627B, 630B, 633, 641B, 651, 651B, 657, 666
2S0304 GASKET
621, 623, 980
7S9342 GASKET
641B, 650B, 657B, 772, 773, 992
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.