AVSPARE.COM
parts catalog

NUT-SPECIAL 2559993 - Caterpillar



2559993 NUT-SPECIAL Caterpillar parts 901C, 902C, 903C NUT
Rating:
59
Alternative (cross code) number:
CA2559993
255-9993
2559993
Caterpillar 2559993 NUT-SPECIAL

Buy NUT-SPECIAL 2559993 Caterpillar genuine, new aftermarket tractor parts with delivery
COMPACT WHEEL LOADER,

Compatible equipment models: 2559993:

COMPACT WHEEL LOADER  901C   902C   903C   Caterpillar
Number on catalog scheme: 13
 
  For full view, you need register

Information:

Removal Procedure
Start By:
Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Illustration 1 g00814138
Remove ten bolts (1).
Remove guard (2).
Illustration 2 g00814144
Illustration 3 g00814145Note: Steering shaft assembly (6) must be separated from lever (3) in order to remove steering shaft assembly (6) from the machine.
Remove two nuts (4), the washers, and the bolts that hold flange (5) to lever (3).
Remove steering shaft assembly (6) from lever (3).
Illustration 4 g00814149
Rear View
Remove the nut and bolt (8).
Remove bottom shaft yoke (7) from the shaft of steering pilot valve (9).
Remove steering shaft assembly (6). Installation Procedure
Illustration 5 g00814145
Illustration 6 g00842649Note: The key that is on the shaft of the steering pilot valve and the keyway of bottom shaft yoke (7) must face toward the front of the machine.
Position steering shaft assembly (6). Install shaft yoke (7) on the shaft of the steering pilot valve. Make sure that the key on the shaft of pilot valve (9) fits securely in the keyway that is in the bottom shaft yoke.
Illustration 7 g00814149
Rear View
Install the nut and bolt (8).
Illustration 8 g00814157
(X) Keyway
Keyway (X) and key (10) should be in the STRAIGHT AHEAD and CENTERED position.
Illustration 9 g00814193
(A) 6.0 1.0 mm (0.24 0.04 inch) dimension.
Note:
Lever (3) must be adjusted on the steering column shaft so that 6.0 1.0 mm (0.24 0.04 inch) protrudes below the lever, as shown.
Align the steering column that protrudes below lever (3) with the pilot hole of mounting flange (5).
Illustration 10 g00814194
Mating surface (B) should have zero clearance.
Push mounting flange (5) onto the steering column until mounting flange (5) is flush with lever (3). There should be no gap between lever (3) and mounting flange (5).
Install two bolts, the washers, and nuts (4).
The steering wheel should be in a STRAIGHT AHEAD and CENTERED position. Refer to Step 9 for the correct adjustment procedure.
Loosen two nuts (4). Adjust the steering wheel to the correct position. Tighten nuts (4).
Illustration 11 g00814138
Install guard (2).
Install ten bolts (1). End By:
Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".

Caterpillar parts catalog:

Caterpillar parts catalog
901C Compact Wheel Loader W4T00001-UP (MACHINE) POWERED BY C1.8 Engine
902C Compact Wheel Loader W5T00001-UP (MACHINE) POWERED BY C2.4 Engine
903C Compact Wheel Loader W6T00001-UP (MACHINE) POWERED BY C2.4 Engine


Parts nut Caterpillar catalog:

5C2874 NUT
120G, 120H, 120H ES, 120H NA, 120M, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1...
6V8187 NUT
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 135H, 135H NA, 1390, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 143H, 14H, ...
5C8312 NUT
10-20B, 1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 1290T, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 1390, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14H, 14H NA, 14M, 160H, 160H ES...
8T4001 NUT
115, 1190T, 1290T, 1390, 14G, 214B, 224B, 2290, 2384C, 2390, 2391, 2470C, 2484C, 2491, 2570C, 2590, 2670C, 2864C, 30/30, 307, 307B, 307C, 308C, 3126B, 320B FM LL, 320C, 320D L, 324D, 324D L, 324D LN, ...
8T3597 NUT-WELD
1090, 1190, 1190T, 1290T, 1390, 216, 216B, 216B3, 226B, 226B3, 228, 2290, 236, 236B, 236B3, 2384C, 2390, 2391, 242B, 246C, 247, 2470C, 247B, 247B3, 248, 2484C, 2491, 256C, 2570C, 2590, 262C, 262C2, 26...
6V9169 NUT
10 FT, 10-20B, 1090, 10B, 115, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14H NA, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16G, 16H, 16M, 216, 228,...
0964876 NUT
303.5E, 303E CR, 304E, 305.5E, 305E, 307, 307E, 308C, 308E, 308E SR, 308E2 CR, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E ...
6F7045 NUT-FULL
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140B, 140G, 140H, 140H ES, 1...
8H5303 NUT
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140B, 140G, 140H, 140H ES, 1...
2559994 NUT
901C, 902C, 903C
2580041 NUT
901C, 902C, 903C
4421500 NUT-RING
901C, 902C, 903C
3830307 NUT-HEX
901C, 902C, 903C
2579607 NUT
901C, 902C, 903C
2559992 NUT
901C, 902C, 903C
4195586 NUT-JAM
901C, 902C, 903C, SE60 V XW
4M5286 NUT
613, 621B, 623, 627, 627B, 631C, 633C, 641B, 657B, 769, 772, 988
2H6886 NUT
621, 631C, 651, 657, 824B, 826B, 834, 988, 992
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.