AVSPARE.COM
parts catalog

GASKET 4F7020 - Caterpillar



4F7020 GASKET Caterpillar parts 955C, 977D, D315 GASKET
Rating:
11
Alternative (cross code) number:
CA4F7020
4F-7020
4F7020
Caterpillar 4F7020 GASKET
Weight: 0.07 pounds 0 kg.

Buy GASKET 4F7020 Caterpillar genuine, new aftermarket tractor parts with delivery
MARINE ENGINE, TRACK LOADER,

You can buy parts: .

$10.50

19 Aug 2019
11 Hundredths Pounds
CTP Caterpillar Gasket (4f7020)
Number on catalog scheme: None
 
  For full view, you need register

Compatible equipment models: 4F7020:

MARINE ENGINE  D315  
TRACK LOADER  955C   977D   Caterpillar

Information:

Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01119759
Loosen jam nut (8) and adjustment screw (7). Loosen jam nut (10) and adjustment screw (9).
Illustration 2 g01131377
Illustration 3 g01946786
Floating valve bridge
(X) Round pocket
(Y) Slotted pocket
(Z) Outside of engine
Apply clean engine oil to pushrod (5).
Apply clean engine oil to valve pushrods (4), and the cup of the valve lifters. Install valve pushrods (4) in the original location.
For floating valve bridge assemblies, use the following procedure.
Apply clean engine oil to the contact surface of bridge assemblies (3) and the valve stems. Install bridge assemblies (3) on the valve stems.
Install the bridge assemblies with the round pocket toward the outside of the engine. Refer to Illustration 3.
Ensure that the crankshaft and the camshafts are in time with each other. Also ensure that the adjustment screws in the rocker arms are loosened completely before the bolts on the rocker shaft are tightened or damage to the valves and the pistons may occur.
If the rocker shaft is not positioned correctly, the oil supply to the sleeve bearings in the rocker arm will be shut off. This will cause seizure of the bearings and severe damage to the engine.Be sure to orient the rocker shaft in the correct position.
Place rocker shaft assembly (2) in position on valve mechanism cover base (6). Make sure that valve pushrods (4) and pushrod (5) are aligned with the rocker arms. Install bolts (1). Tighten the bolts to a torque of 85 N m (63 lb ft). Tighten the bolts anadditional60 degrees 5 degrees.
Illustration 4 g01119849
Adjust the valve lash according to Testing and Adjusting, "Valve Lash and Valve Bridge Adjustment". Hold adjustment screw (7) of the rocker arm assembly and tighten jam nut (8) to a torque of 70 15 N m (52 11 lb ft).
Adjust the electronic unit injector lash according to Testing and Adjusting, "Fuel Injector Adjustment". Hold adjustment screw (9) of the rocker arm assembly and tighten nut (10). If nut (10) is 5/8 inch thread, tighten to a torque of 120 15 N m (89 11 lb ft). If nut (10) is 1/2 inch thread, tighten to a torque of 70 15 N m (52 11 lb ft).End By:
Install the valve mechanism cover.

Caterpillar parts catalog:

Caterpillar parts catalog
955 TRAXCAVATOR 12A00001-08418 (MACHINE)
977 TRAXCAVATOR 20A00001-04222 (MACHINE)
955 TRAXCAVATOR 12A00001-08418 (MACHINE)
977 TRAXCAVATOR 20A00001-04222 (MACHINE)
955 TRAXCAVATOR 12A00001-08418 (MACHINE)
977 TRAXCAVATOR 20A00001-04222 (MACHINE)
955 TRAXCAVATOR 12A00001-08418 (MACHINE)
977 TRAXCAVATOR 20A00001-04222 (MACHINE)
955 TRAXCAVATOR 12A00001-08418 (MACHINE)
977 TRAXCAVATOR 20A00001-04222 (MACHINE)
D315 MARINE ENGINE 05V00001-UP


Parts gasket Caterpillar catalog:

4H7869 GASKET
1090, 1150, 1160, 1190, 1190T, 120G, 120M, 1290T, 12F, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 1390, 140B, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 1...
2F4586 GASKET-EXHAUST PIPE
12E, 3208, 3304, 955C, 977D
4F9785 GASKET
583H, 651, 955C, D315, D342, D364, D375D, D379, D379B, D397D, D398, D398B, D399, D9E
7B7129 GASKET-FLANGE TO WATER PUMP
1676, 583K, 641B, 650B, 657B, 772, 773, 955H, 980, D10, D315, D320A, D326F, D336, D337, D337F, D342, D342C, D343, D346, D348, D349, D353C, D8H, G342C, G343, G353D
1A2024 GASKET
16, 1673, 1673B, 1693, 583H, 631C, 657B, 769, 824, 824B, 834, 955C, 966C, 977D, 983, 988, D315, D326F, D330A, D330B, D337, D337F, D342, D342C, D343, D364, D375D, D397D, D8H, D8K, G343
2H2519 GASKET
1693, 594, 621, 641, 651, 657, 666, 769, 824, 955C, 980, D315, D320A, D326F, D337, D337F, D342, D342C, D343, D353C, D8H, D9E, D9G, D9H, G342C
6H9949 GASKET
12E, 16, 1673, 1693, 657, 955C, 977H, 988, D315, D326F, D330A, D342, D342C, D343, D353C, D375D, D4D, D8H, D9E, D9G, D9H
5B5937 GASKET
583H, 955C, 977D, D315, D337F, D342, D353C, D397D, D8H, D9E
4B1453 GASKET
120G, 12F, 130G, 14E, 14G, 16, 16G, 613, 621, 621B, 621R, 623, 627, 627B, 631C, 637, 637B, 637D, 641, 641B, 650B, 651, 657, 657B, 666, 769, 769C, 772, 773, 773B, 777, 955C, D250E, D300E, D350E, D400E
6F5188 GASKET
14E, 16, 44, 46, 50, 515, 525, 525D, 535D, 545D, 555D, 621, 621B, 621E, 621F, 621G, 621H, 621K, 623, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631C, 63...
5N8463 GASKET
D379, D379B, D398
1W7595 GASKET-OIL COOLER
215, 3208, 613B, 613C, 926, 953
4F9241 GASKET
650B, 657B, D315, D337, D364, D375D, D397D
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.