AVSPARE.COM
parts catalog

EXTENSION FLAT (front R.H.) 5V3390 - Caterpillar



5V3390 EXTENSION FLAT (front R.H.) Caterpillar parts 920 EXTENSION
Rating:
14
Alternative (cross code) number:
CA5V3390
5V-3390
5V3390
Caterpillar 5V3390 EXTENSION FLAT (front R.H.)
Weight: 6 pounds 2 kg.

Buy EXTENSION FLAT (front R.H.) 5V3390 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 5V3390:

WHEEL LOADER  920   Caterpillar
Number on catalog scheme: 5
 
  For full view, you need register

Information:

Introduction:
The 4P-9048 Control Assembly is used in 3114 MUI Engines. The 102-7459 Control Assembly is used in 3116, and 3126 MUI Engines.Adaptable To:
The 4P-9048 Control Assembly replaces the former 7C-1514 Control Assembly in the 7W-8600 Fuel Injection Control Group. The 102-7459 Control Assembly replaces the former 4P-9047 Control Assembly in the 7W-6989 Fuel Injection Control Group.The 4P-9048 Control Assembly and 102-7459 Control Assembly provides close clearance shaft bearings and requires different procedures for installation than the former 7C-1514 Control Assembly and 4P-9047 Control Assembly.The bearing supports on the former 7C-1514 Control Assembly were factory set.The 4P-9048 Control Assembly and 102-7459 Control Assembly center supports are now tightened AFTER installation on the engine.Installation of the 4P-9048 Control Assembly (3114 Engines):
1. See end view of bearing support (D). Assure two screws (1) in inner bearing bracket (B) are loose.2. Tighten bolts (2) for the outer bearing brackets (A and C) to a torque of 12 3 N m (9 2 lb ft).3. Tighten bolts (2) for the inner bearing bracket (B) to a torque of 12 3 N m (9 2 lb ft).4. Position the inner bearing (B) to allow free rotation of the rack control rod.5. Tighten two screws (1) on inner bearing bracket (B) to 3.5 .2 N m (31 2 lb in).6. Control rod must rotate when force of 4.4 N (1 lb) or less is applied to control lever (3) in direction indicated by arrows.Installation of the 102-7459 Control Assembly (3116/3126 Engines):
1. See end view of bearing support (E). Assure that two screws (1) in each inboard bracket (B and C) are loose.2. Tighten bolts (2) for outer bearing brackets (A and D) to a torque of 12 3 N m (9 2 lb ft).3. Tighten bolts (2) for inner bearing brackets (B and C) to a torque of 12 3 N m (9 2 lb ft).4. Position the inner (B and C) bearings to allow free rotation of the rack control rod.5. Tighten two screws (1) on each inboard bracket to a torque of 3.5 .2 N m (31 2 lb in). The control rod must rotate when a force of 4.4 N (1 lb) or less is applied to control lever (3) in direction indicated by arrows.

Caterpillar parts catalog:

Caterpillar parts catalog
920 WHEEL LOADER 41J04371-UP (MACHINE)


Parts extension Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.