AVSPARE.COM
parts catalog

FENDER ASSEM. (rear L.H.) 5V3415 - Caterpillar



5V3415 FENDER ASSEM. (rear L.H.) Caterpillar parts 950 FENDER
Rating:
55
Alternative (cross code) number:
CA5V3415
5V-3415
5V3415
Caterpillar 5V3415 FENDER ASSEM. (rear L.H.)
Weight: 2 pounds 1 kg.

Buy FENDER ASSEM. (rear L.H.) 5V3415 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 5V3415:

WHEEL LOADER  950   Caterpillar
Number on catalog scheme: 14
 
  For full view, you need register

Information:


Illustration 1 g02068536
Schematic for the Steering Angle SensorThis diagnostic code is associated with the Steering Angle Sensor (Steering Cylinder Linear Sensor). The FMI 03 means that the Machine ECM has determined that the voltage of the circuit for the sensor is above normal. Note: The Machine ECM is located inside the Center Console.The output frequency of the position sensor is approximately 500 hz. The duty cycle of the signal changes as the position sensor moves. The duty cycle varies from 5 to 95 percent.The possible causes of this diagnostic code are listed below:
The signal circuit for the sensor is open.
The signal circuit for the sensor is shorted to the +battery circuit.
The sensor has failed.
The power circuit or the ground circuit has failed.
The Machine ECM has failed. This situation is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0163 FMI 03 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.Test Step 1. CHECK FOR POWER AT THE SENSOR.
Do not disconnect the harness connector from the sensor.
Turn the key start switch and the disconnect switch to the ON position.
At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along the voltage supply wire (contact A).
Measure the voltage from contact A to frame ground.Expected Result:The voltage is battery voltage.Results:
OK - The voltage is battery voltage. Proceed to Test Step 2.
NOT OK - The voltage is not battery voltage. The + battery circuit in the machine harness has failed.Repair: Replace the machine harness or repair the machine harness.STOPTest Step 2. CHECK FOR PROPER GROUND AT THE SENSOR.
The machine harness remains connected to the sensor.
Turn the key start switch and the disconnect switch to the OFF position.
Remove the 7X-1710 Multimeter Probe from the voltage supply wire (contact A).
At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along the ground wire (contact B).
Measure the resistance from contact B to frame ground.Expected Result:The resistance is less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. The ground circuit is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5 ohms. The ground circuit in the machine harness has failed.Repair: Replace the machine harness or repair the machine harness.STOPTest Step 3. CHECK THE WIRING HARNESS OF THE SENSOR FOR AN OPEN CIRCUIT.
The key start switch and the disconnect switch remain in the OFF position.
Disconnect the machine harness from the sensor.
At the harness connector for the sensor, connect a jumper wire between contact B and contact C.
Disconnect the machine harness connectors from the Machine ECM.
At the harness connector for the Machine ECM, measure the resistance between contact J2-41 and contact J2-22.Expected Result:The resistance measurement is less than 5 ohms.Results:
OK - The resistance measurement is less than 5 ohms. The circuit is correct. Proceed to Test Step

Caterpillar parts catalog:

Caterpillar parts catalog
950 WHEEL LOADER 43J06268-UP (MACHINE) POWERED BY 3304 ENGINE


Parts fender Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.