AVSPARE.COM
parts catalog

FENDER ASSEM. (rear R.H.) 5V3433 - Caterpillar



5V3433 FENDER ASSEM. (rear R.H.) Caterpillar parts 950 FENDER
Rating:
54
Alternative (cross code) number:
CA5V3433
5V-3433
5V3433
Caterpillar 5V3433 FENDER ASSEM. (rear R.H.)
Weight: 1 pounds 0 kg.

Buy FENDER ASSEM. (rear R.H.) 5V3433 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 5V3433:

WHEEL LOADER  950   Caterpillar
Number on catalog scheme: 13
 
  For full view, you need register

Information:


Illustration 1 g02131714
Schematic for Left and Right Drive Motor Speed SensorsThis diagnostic code is associated with the Left Drive Speed Sensor. The FMI 08 means that the ECM has determined that the signal frequency or the signal pulse width is not within the expected range. There will be two monitored sensor signals for each motor. One of the signals is primary and one signal is secondary. A diagnostic code is generated if the primary signal and the secondary signal differ by more than 35 RPM for a time greater than the debounce time. Note: The "Machine ECM" is located inside the Center Console. The possible causes of this diagnostic code are listed below:
The sensor has failed.
Intermittent connections or poor connections
Mechanical devices are loose.
The ECM has failed. This situation is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0154 FMI 08 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure. System Response:When this diagnostic code is active, the following occurs:
The machine operates in open loop mode.
The speed limit is applied in travel mode.
The operator station fault lamp is active.Test Step 1. CHECK THE RETURN CIRCUIT
Turn the key start switch to the OFF position.
Disconnect the machine harness connector from the sensor.
At the machine harness connector for the sensor, measure the resistance between return circuit J1-45 (C234-BK) and the frame ground.Expected Result:The resistance should measure 5 ohms or less. Results:
OK - The return circuit is correct. Proceed to test step 2.
NOT OK - The return circuit (C234-BK) in the machine harness is open.Repair: Repair the harness or replace the harness.STOPTest Step 2. CHECK THE POWER SUPPLY CIRCUIT AT THE SENSOR
The machine harness remains disconnected from the sensor.
Turn the key start switch to the ON position.
At the machine harness for the sensor, measure the voltage. Measure the voltage from contact 1 (wire A105-OR) and contact 3 (wire C234-BK).Expected Result:The voltage that is measured is between 8 0.5 DCV. Results:
OK - The power supply circuit is correct. Proceed to test step 3.
NOT OK - The power supply circuit is open between the sensor and the ECM.Repair: Repair the harness or replace the harness.STOPTest Step 3. CHECK THE ECM AND THE HARNESS.
The key start switch remains ON.
The machine harness remains disconnected from the sensor.
At the machine harness for the sensor, measure the voltage for the signal circuit 1. Measure the voltage from contact 2 (G808-BU) and contact 3 (C234-BK).
At the machine harness for the sensor, measure the voltage for the signal circuit 2. Measure the voltage from contact 4 (G809-GN) and contact 3 (C234-BK).Expected Result:The voltage that is measured is 5 0.5 DCV for both measurements. Results:
OK - The signal circuits are correct. Proceed to test step 6.
NOT OK - The machine harness or the ECM has failed. Proceed to test step 4.Test Step 4. CHECK FOR A

Caterpillar parts catalog:

Caterpillar parts catalog
950 WHEEL LOADER 43J06268-UP (MACHINE) POWERED BY 3304 ENGINE


Parts fender Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.