AVSPARE.COM
parts catalog

NUT 5V3580 - Caterpillar



5V3580 NUT Caterpillar parts NUT
Rating:
36
Alternative (cross code) number:
CA5V3580
5V-3580
5V3580
Caterpillar 5V3580 NUT
Weight: 82 pounds 37 kg.

Buy NUT 5V3580 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01857042
Schematic of the data link circuitThis diagnostic code is recorded when the power train ECM does not receive expected information. The information from the Cat data link indicates the abnormal values in the readout. The possible causes of this diagnostic code are listed below. The causes are listed in order of probability:
Poor electrical connection at a machine harness connector
The circuit for the Cat data link in the machine harness is shorted to ground.
The circuit for the Cat data link in the machine harness is shorted to the +battery.
The circuit for the Cat data link in the machine harness is open.Service Notes: Ensure that the desired diagnostic code (CID and FMI) is on hold. Ensure that the service code indicator shows "SERV CODE".Test Step 1. CHECK FOR OTHER CODES.
Check other electronic control modules for a similar diagnostic code. If a similar diagnostic code is found, exit this test. Perform the corresponding procedures for the other diagnostic codes that are shown.Expected Result:There are other diagnostic codes that are showing.Results:
OK - Exit this procedure and perform the other procedures for the diagnostic codes that are shown.STOP
NOT OK - There are not any other diagnostic codes that are shown. Proceed to test step 2.Test Step 2. INSPECT THE HARNESS CONNECTORS.
Turn the disconnect switch to the OFF position.
Inspect the connections for the machine harness that are related to the Cat data link.
Make sure that connectors are clean and tight.Expected Result:The machine harness is correct.Results:
OK - The machine harness is correct. Proceed to test step 3.
NOT OK - The machine harness is not correct.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK FOR A SHORT TO GROUND.
The disconnect switch remains in the OFF position.
Disconnect the machine harness from all the electronic control modules that use the Cat data link.
At the machine harness connector for the power train ECM, measure the resistance between frame ground and the circuits of the Cat data link, contacts J1-3 (wire 892-BR) and J1-9 (wire 893-GN). Expected Result:The resistance is greater than 5000 ohms.Results:
OK - The resistance is greater than 5000 ohms. The harness circuit resistance is correct. Proceed to test step 4.
NOT OK - The resistance is less than 5000 ohms. The machine harness has failed. There is a


Parts nut Caterpillar catalog:

5U8825 NUT
Caterpillar
5U5253 NUT
Caterpillar
5U3602 NUT
Caterpillar
5U1048 NUT
Caterpillar
5U0946 NUT
Caterpillar
5W1319 NUT
Caterpillar
5W1311 NUT
Caterpillar
5W1301 NUT
Caterpillar
5W1299 NUT
Caterpillar
5W1298 NUT
Caterpillar
5W1262 NUT
Caterpillar
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.