AVSPARE.COM
parts catalog

PLATE ASSEM. 5V3642 - Caterpillar



5V3642 PLATE ASSEM. Caterpillar parts 966D PLATE
Rating:
64
Alternative (cross code) number:
CA5V3642
5V-3642
5V3642
Caterpillar 5V3642 PLATE ASSEM.
Weight: 0.05 pounds 0 kg.

Buy PLATE ASSEM. 5V3642 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 5V3642:

WHEEL LOADER  966D   Caterpillar
Number on catalog scheme: 5
 
  For full view, you need register

Information:


Illustration 1 g01365165
Schematic of the Electrical System power supply to the Implement (Screed) ECM This diagnostic code is recorded when the Implement (Screed) ECM reads the system voltage as being below 18 DCV.Note: The Implement (Screed) ECM is located under the Screed Platform.The possible causes of this diagnostic code are listed:
A charging system component has failed.
The machine harness has failed.
The ECM has failed. This situation is unlikely. System Response:When this diagnostic code is active, the following occurs:
Components connected to controller will not log faults.
Machine may become inoperable.Test Step 1. CHECK THE BATTERY VOLTAGE.
Start the engine and run the engine at high idle for several minutes.
Measure the voltage of the battery at the battery posts.Expected Result:The battery voltage should be greater than 18 DCV.Results:
OK - The battery voltage is greater than 18 DCV. The battery voltage is correct. Proceed to test step 2.
NOT OK - The battery voltage is NOT greater than 18 DCV.Repair: Check the charging system. See Special Instruction, REHS0354.STOPTest Step 2. CHECK THE SYSTEM VOLTAGE AT THE ECM.
The engine remains running at high idle.
DO NOT DISCONNECT the machine harness from the ECM.
Use the 7x-1710 Multimeter Probe to measure the positive voltage (DCV) between contacts J1-31, J1-39 (wire 140-RD) and ground contacts J1-13, J1-23 (wire 200-BK). Expected Result:The voltage measurement is greater than 18 DCV.Results:
OK - The voltage is greater than 18 DCV. The battery voltage is correct. Proceed to test step 3.
NOT OK - The voltage is NOT correct. The machine harness has failed.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connectors from the ECM. Inspect the harness and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Clear all the active diagnostic codes.
Operate the machine.
View the status of CID 0168 FMI 04.Expected Result:The diagnostic code is NO longer active.Results:
YES - The diagnostic code is NO longer active. The diagnostic code does not exist at this time. The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.STOP
NO - The diagnostic code has NOT been corrected. Repair: Failure of the ECM is unlikely. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, the ECM may have failed. Prior to replacing an ECM, always contact the Technical Communicator for your dealer for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacement, refer to Troubleshooting, "Electronic Control Module (ECM) - Replace".STOP

Caterpillar parts catalog:

Caterpillar parts catalog
966D WHEEL LOADER 94X00001-06488 (MACHINE) POWERED BY 3306 ENGINE


Parts plate Caterpillar catalog:

2P1738 PLATE AS-OIL PAN
120B, 12G, 12H, 12H ES, 12H NA, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 235B, 235C, 330, 330 FM L, 330 L, 3306, 3306B, 3306C, 330B, 330B L, 350, 5...
1U3508 PLATE
446B, 446D, 530B, 814F, 814F II, 815F, 815F II, 816F, 816F II, 918F, 924F, 928F, 938F, 938G, 938G II, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, IT1...
8P9770 PLATE
14G, 215, 215B, 215C, 215D, 225, 225D, 229, 229D, 231D, 235, 235B, 235C, 235D, 245, 245B, 24H, 24M, 307C, 311C, 311D LRR, 311F LRR, 312, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 3...
9C9159 PLATE
3512B, 3516B, 3516C, 587T, 814B, 814F, 815B, 815F, 816F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G,...
8P1964 PLATE-CLUTCH
30/30, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 611, 615, 615C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 972M, 9...
9G8020 PLATE-RETAINER
30/30, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 611, 615, 615C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 980C, 9...
6I8500 PLATE-CLUTCH
30/30, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 611, 615C, 814B, 814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, 980G, 980G II, 980H, 980K, D250E, D250E II, D25D, D300E, D30...
4J3816 PLATE
215, 215B, 225, 229, 235, 235B, 235D, 245, 245B, 24H, 24M, 5110B, 5130, 5130B, 5230, 5230B, 528, 589, 621, 621B, 621E, 621F, 621G, 621R, 623E, 623F, 623G, 627B, 627E, 627F, 627G, 631C, 631E, 631G, 633...
9V0247 PLATE
318C, 320B, 320C, 325B L, 325C, 330B L, 330C, 345B II, 345B L, 814F, 814F II, 815F, 815F II, 824G, 824G II, 824H, 825G, 825G II, 825H, 918F, 928F, 936, 936F, 938F, 938G, 938G II, 950B, 950B/950E, 950F...
9P8283 PLATE-CLUTCH
966D, 966F, 966F II, 970F, D6H, D6H XL, D6H XR
6V4351 PLATE-INNER RACE
814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K, 972M, R1300, R1300G
4V0015 PLATE-LOCK
12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 1...
8V0655 PLATE
814B, 815B, 966D
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.