AVSPARE.COM
parts catalog

LEVER 5V3649 - Caterpillar



5V3649 LEVER Caterpillar parts 920, 930, D6H, D6H XL, D7H LEVER
Rating:
81
Alternative (cross code) number:
CA5V3649
5V-3649
5V3649
Caterpillar 5V3649 LEVER
Weight: 0.50 pounds 0 kg.
Information:
ARM OFFSET DIMENSION  6.5  mm
AXIS CENTERLINE TO CENTERLINE DIMENSION  50  mm
AXIS OFFSET DIMENSION  0  mm
FULCRUM HOLE DIAMETER  19.05  mm
LINKAGE HOLE DIAMETER  13.8  mm

Buy LEVER 5V3649 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR, WHEEL LOADER,

Compatible equipment models: 5V3649:

TRACK-TYPE TRACTOR  D6H   D6H XL   D7H  
WHEEL LOADER  920   930   Caterpillar
Number on catalog scheme: 91
 
  For full view, you need register

Information:


Clean the sealing surface of the filter mounting base. Ensure that all of the old oil filter gasket is removed.
Apply clean engine oil to the new oil filter gasket.
Do not fill the oil filters with oil before installing them. This oil would not be filtered and could be contaminated. Contaminated oil can cause accelerated wear to engine components.
Install the oil filter. Tighten the oil filter until the oil filter gasket contacts the base. Tighten the oil filter by hand according to the instructions that are shown on the oil filter. Do not overtighten the oil filter. Fill the Engine Crankcase
Remove the oil filler cap. Refer to the Operation and Maintenance Manual, "Refill Capacities and Recommendations" topic or to the Operation and Maintenance Manual, "Fluid Recommendations" for more information about selecting the correct engine oil and finding the correct refill capacity for your engine. Fill the crankcase with the proper amount of oil.
If equipped with an auxiliary oil filter or system, extra oil must be added when filling the crankcase. Follow the OEM or filter manufacturer's recommendations. If the extra oil is not added, the engine may starve for oil.
To help prevent crankshaft or bearing damage, crank engine to fill all filters before starting. Do not crank engine for more than 30 seconds.
Start the engine and run the engine at "LOW IDLE" for 2 minutes. Perform this procedure in order to ensure that the lubrication system has oil and that the oil filters are filled. Inspect the oil filter for oil leaks.
Stop the engine and allow the oil to drain back to the sump for a minimum of 10 minutes.
Remove the oil level gauge in order to check the oil level. Maintain the oil level between the "ADD" and "FULL" marks on the "ENGINE STOPPED" side of the oil level gauge.
Remove the "DO NOT OPERATE" tag from the ignition keyswitch. Adjustments to the Oil Change Intervals
Many conditions affect the selection of an oil change interval. Proper oil change intervals are important for maintaining engine service life and engine performance and fully utilizing the lubricant. The engine oil must be able to control the following items: corrosion, oxidation, soot and wear metals. The engine oil must be able to control the conditions during the time between oil changes. In some severe service applications, reducing the oil change interval may be necessary in order to maintain the integrity of the engine lubricant. Refer to this Operation and Maintenance Manual, "Severe Service Application" or consult with your Cat dealer in order to determine whether your engine is operating under severe service conditions.Fuel consumption and oil consumption are the most important factors that are used in order to calculate an oil change interval. All engines do not consume fuel and oil at the same rate due to several factors: manufacturing tolerances, maintenance variations and engine application.Extended Oil Change Intervals
Note: The following requirements must be met in order to use table 1. :
CatDEO-ULS is used or an oil that meets the requirements of the

Caterpillar parts catalog:

Caterpillar parts catalog
D6H Series II Track-Type Tractor Direct Drive 1FJ04000-UP (MACHINE) POWERED BY 3306 Engine
D6H Series II XL Track-Type Tractor Power Shift 8ZJ00001-UP (MACHINE) POWERED BY 3306 Engine


Parts lever Caterpillar catalog:

8G4331 LEVER
D6H, D6H XL, D7H
3T6756 LEVER
D6H, D6H XL, D7H
3T6750 LEVER
D6H, D6H XL, D7H
3T6751 LEVER
D6H, D6H XL, D7H
4D8924 LEVER
16, 633D, 637D, 657B, 920, 930, 930R, D10N, D10R, D6H, D6H XL, D6H XR, D9L
8M6773 LEVER-GOVERNOR CONTROL
561C, 561D, D4E, D4E SR, D5, D5B, D5E, D6C, D6D, D6E SR
1V0026 LEVER
561D, 941, 955L, D4D, D4E, D4E SR, D5, D5B, D5E, D6C, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D7G, D7G2
5K6079 LEVER
561D, 955K, 955L, D4E, D4E SR, D5B, D5E, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL, D7G, D7G2
6D5707 LEVER
14E, 571G, D4E, D4E SR, D5B, D5E, D6D, D6E SR, D7G
8M6770 LEVER-GOVERNOR CONTROL
561C, 561D, 814B, D4E, D4E SR, D5, D5B, D5E, D6C, D6D, D6E SR
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.