AVSPARE.COM
parts catalog

PLATE 5V3798 - Caterpillar



5V3798 PLATE Caterpillar parts 920, 930 PLATE
Rating:
81
Alternative (cross code) number:
CA5V3798
5V-3798
5V3798
Caterpillar 5V3798 PLATE
Weight: 5 pounds 2 kg.

Buy PLATE 5V3798 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 5V3798:

WHEEL LOADER  920   930   Caterpillar
Number on catalog scheme: 15
 
  For full view, you need register

Information:


Illustration 1. Deposits on prechamber.These compounds will usually redissolve in water. Follow the "Procedure to Dissolve Deposits".
Procedure To Dissolve Deposits
1. In order to dissolve these deposits, drain the coolant and fill the cooling system with clear water.2. Fasten cardboard or light plywood to the radiator on the opposite side of the fan.3. Start and run the engine at high idle rpm with no load. Allow the temperature of the coolant to increase, but do not exceed 93°C (200°F). The radiator cap is to be set loosely on the filler neck during this operation and load is not to be applied to the engine.4. After a one hour period, decrease engine speed to low idle. Remove the material blocking the radiator and continue to run the engine at low idle for five minutes.Illustration 2 shows the same prechamber after 30 minutes. Illustration 3 shows the same prechamber after 60 minutes.
Illustration 2. Prechamber after 30 minutes.5. Stop the engine, drain and discard this water.6. Replace the water conditioner filter and element if used. If a water conditioner filter and element are not used, add cooling system conditioner to obtain a 3 to 6% concentration after filling the system.7. Refill the cooling system to the full mark with a 50/50 mixture of clean antifreeze and water for coolant. Note: If bulk antifreeze or mix is used, obtain a sample in a clear sample bottle and let it stand for 30 minutes. If the antifreeze mix is discolored, has particles floating in it or has a layer of darkish material floating on the surface, the mix should be filtered through a filter media before pouring the mix into the cooling system. Start the engine and top off to the full mark once again.
Illustration 3. Prechamber after 60 minutes.
Excessive coolant conditioner (greater than the recommended 6% initial fill) together with concentrations of antifreeze greater than 65% cause a mud-like deposit to form and may result in radiator tube blockage and overheating.
Coolant mixtures in excess of 50% antifreeze should not be used unless temperatures below -34°C (-30°F) are expected. Increase to 60% antifreeze in this case but as the outside air temperatures start to be consistently above 0°C (32°F), switch back to the 50/50 mixture.
Antifreee concentrations in excess of 63% provide less rather than more freeze protection.
A good practice to follow after operating an engine is to return the engine speed to low idle for 5 minutes before shutting the engine down. This reduces the surface temperature of the prechambers, heads and liners minimizing localized boiling at these areas. This will also reduce the plating effect of the compounds in the coolant.

Caterpillar parts catalog:

Caterpillar parts catalog
930 WHEEL LOADER 41K05315-UP (MACHINE) POWERED BY 3304 ENGINE
920 WHEEL LOADER 62K07095-UP (MACHINE) POWERED BY 3304 ENGINE
920 WHEEL LOADER 41J04371-UP (MACHINE)
930 WHEEL LOADER 79J03733-UP (MACHINE) POWERED BY 3304 ENGINE
920 WHEEL LOADER 41J04371-UP (MACHINE)
930 WHEEL LOADER 79J03733-UP (MACHINE) POWERED BY 3304 ENGINE
920 WHEEL LOADER 75J03573-UP (MACHINE) POWERED BY 3304 ENGINE
930 WHEEL LOADER 73U01313-UP (MACHINE) POWERED BY 3304 ENGINE


Parts plate Caterpillar catalog:

7N7809 PLATE
120H, 120H NA, 12H, 12H NA, 135H, 135H NA, 140H, 140H NA, 140K, 14H NA, 160H, 160H NA, 160K, 215B, 235, 3116, 3126, 3126B, 3176B, 3176C, 3196, 3208, 3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3406E...
3T0862 PLATE AS-BRUSH
120G, 12G, 130G, 140G, 14G, 160G, 1673C, 16G, 215, 215B, 235, 245, 3176B, 3176C, 3196, 3208, 330 L, 3304, 3304B, 3306, 3306B, 3306C, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3412, 3412C, 3412E, ...
3G5980 PLATE
153, 416, 416B, 426B, 428, 428B, 438B, 446, 446B, 446D, 508, 515, 518, 518C, 525, 525B, 525C, 528, 535B, 535C, 539, 545, 545C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 824C, 826C, 916,...
6H5139 PLATE-PRESSURE
120G, 12F, 12G, 130G, 140, 141, 14E, 14G, 153, 16, 163, 16G, 172, 173B, 183, 183B, 184, 191, 193, 30/30, 416, 416B, 426B, 428, 428B, 438B, 446, 46, 508, 515, 517, 518, 525, 525D, 527, 528, 535D, 545D,...
4S6417 PLATE-THRUST
120G, 130G, 215B, 225, 3304, 3304B, 515, 517, 518C, 525, 527, 920, 936F, 941, 950, 951B, 955H, D320A, D330A, D4D, D4E, D4E SR, D4H, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, G3304, G3304B
4N4691 PLATE AS-BRUSH
120G, 3208, 3304, 3306, 3306B, 518, 613, 613B, 613C, 920, 930, 950B, 951B, 955L, 963, D4D, D4E, D5H, D6C, G936
7N1282 PLATE AS-BRUSH
1673C, 215, 225, 3304, 3306, 3306B, 518, 920, 943, 950B, 963, D250B, D25C, D300B, D30C, D350C, D35C, D4D, D4E, D5B, G936, IT28, IT28B
4S8704 PLATE
518, 518C, 528, 528B, 530B, 920, 930, 941, 951B, D4D, D4E
3P8393 PLATE
518C, 528, 528B, 530B, 920, 930, D4D, D4E
2R0694 PLATE-BRAKE VALVE
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 621E, ...
7K0251 PLATE
518, 910, 920
5V4877 PLATE
920, 930, 930R
4V3679 PLATE
920, 930, 930R
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.