AVSPARE.COM
parts catalog

STRIP 5V3876 - Caterpillar



5V3876 STRIP Caterpillar parts D4D, D4E, D4E SR STRIP
Rating:
63
Alternative (cross code) number:
CA5V3876
5V-3876
5V3876
Caterpillar 5V3876 STRIP
Weight: 4 pounds 2 kg.

Buy STRIP 5V3876 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

You can buy parts: .

$26.63

25 Nov 2018
Caterpillar Strip 5V3876 New
$26.00

11 Mar 2019
461 Hundredths Pounds
Caterpillar STRIP (5V3876)
Number on catalog scheme: 3
 
  For full view, you need register

Compatible equipment models: 5V3876:

TRACK-TYPE TRACTOR  D4D   D4E   D4E SR   Caterpillar

Information:

Conditions Which Generate This Code:
Illustration 1 g01238171
Schematic of the transmission oil temperature sensorThis diagnostic trouble code is associated with the transmission oil temperature sensor. The FMI 3 means that the ECU has determined that the voltage of the circuit for the sensor is above normal.The possible causes of the diagnostic trouble code are listed:
The energize circuit of the sensor is open.
The sensor has failed.
The ECU has failed. The ECU failing is unlikely.Note: The following test procedure may create other diagnostic trouble codes. Ignore these created diagnostic trouble codes and clear these diagnostic trouble codes when the original diagnostic trouble code has been corrected. Ensure that the diagnostic trouble code of SPN 177 FMI 3 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. CHECK THE VOLTAGE AT THE SENSOR.
Turn the disconnect switch and the key start switch to the ON position.
Disconnect the sensor from the machine harness.
At the machine harness connector for the sensor, measure the voltage between contact 1 (wire 428-OR) and contact 2 (wire 202-BK).Expected Result:The voltage is approximately 5 VDC.Results:
OK - The voltage is approximately 5 VDC. Proceed to test step 5.
NOT OK - The voltage is not approximately 5 VDC. Repair: There is a problem with the machine harness or the ECU has failed. It is unlikely that the ECU has failed. Proceed to test step 2.Test Step 2. CHECK FOR AN OPEN IN THE SUPPLY CIRCUIT.
The key start switch and the disconnect switch remain in the ON position.
The sensor remains disconnected from the machine harness.
At the machine harness connector for the sensor, measure the voltage from contact 1 (wire 428-OR) to ground.Expected Result:The voltage is approximately 5 VDC.Results:
OK - The voltage measurement is approximately 5 VDC. Proceed to test step 3.
NOT OK - The voltage does not measure approximately 5 DC.Repair: The supply circuit is not correct. Repair the circuit or replace the circuit. Proceed to Test Step 5.Test Step 3. CHECK FOR AN OPEN IN THE RETURN CIRCUIT.
Turn the disconnect switch and the key start switch to the OFF position.
The sensor remains disconnected from the machine harness.
Disconnect the machine harness connector J1 from the ECU.
At the machine harness connector for the sensor, install a jumper wire from contact 2 (wire 202-BK) to ground.
At the machine harness connector for the ECU, measure the resistance from contact J1-21 (wire 202-BK) to ground.Expected Result:The resistance measurement is less than 5000 ohms.Results:
OK - The resistance measurement is less than 5000 ohms. The harness is correct.Repair: The sensor has failed. Replace the sensor. Proceed to Test Step 5.
NOT OK - The resistance that is measured is not correct.Repair: There is an open in the machine harness. The open is in the return circuit with the high resistance measurement. Repair the harness or replace the harness. Proceed to Test Step 5.Test Step 4. CHECK THE SENSOR.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Disconnect the sensor with the active diagnostic trouble

Caterpillar parts catalog:

Caterpillar parts catalog
D4E SR Track-Type Tractor Direct Drive 2DJ01400-UP (MACHINE) POWERED BY 3304 Engine


Parts strip Caterpillar catalog:

1H2629 STRIP-INSULATION
1090, 1190, 1190T, 120G, 120M, 120M 2, 1290T, 12E, 12G, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140G, 140H, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14E, 14G, 14H, 14M, 16, 160G, 160H, 160M, 160M 2, 160M ...
4K4780 STRIP ASSEM.
561C, 561D, 941, 951B, 955H, 955K, 955L, D4D, D5, D5B
7K1293 STRIP
561C, 561D, 941, 951B, 955K, 955L, D4D, D4E, D5, D5B
5V3875 STRIP
D4D, D4E, D4E SR
7K1294 STRIP AS-WEAR
941, D4D, D4E, D4E SR
4M3067 STRIP
941, 951B, 955H, 955K, 955L, D4D, D5
2V7221 STRIP
941, 955K, 955L, D4D
5S6415 STRIP
D4D, D4E, D4E SR
5S7996 STRIP
D4D, D4E, D4E SR
5S6138 STRIP
955K, 955L, D4D, D4E, D4E SR
1N4135 STRIP-TAPPING
926, 936, 936F, 963, 963B, G936, IT28
7K1294 STRIP AS-WEAR
941, D4D, D4E, D4E SR
5V3875 STRIP
D4D, D4E, D4E SR
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.