AVSPARE.COM
parts catalog

BUCKET AS-GENERAL PURPOSE 9V8959 - Caterpillar



9V8959 BUCKET AS-GENERAL PURPOSE Caterpillar parts IT12, IT12B, IT14B, IT14F, IT18, IT18B, IT18F, IT24F BUCKET
Rating:
57
Alternative (cross code) number:
CA9V8959
9V-8959
9V8959
Caterpillar 9V8959 BUCKET AS-GENERAL PURPOSE
Weight: 1365 pounds 619 kg.

Buy BUCKET AS-GENERAL PURPOSE 9V8959 Caterpillar genuine, new aftermarket tractor parts with delivery
INTEGRATED TOOLCARRIER,

Compatible equipment models: 9V8959:

INTEGRATED TOOLCARRIER  IT12   IT12B   IT14B   IT14F   IT18   IT18B   IT18F   IT24F   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

NOTE C: To verify overspeed shutdown system operation, push in for a moment the verify push button. The engine must shut down at 75% or more of overspeed setting.NOTE D: Input Voltage: Maximum 37 VDC Minimum 8 VDC.NOTE E: The engine overspeed setting rpm is 118% of rated engine rpm.NOTE F: The magnetic pick-up frequency (HZ) at the overspeed or cranking termination setting is calculated with the formula that follows: If the rated speed of the engine is other than shown in the chart, the magnetic pick-up frequency for the overspeed setting can be found according to NOTES E and F.If a 2301 Governor is used, only one magnetic pick-up is needed. Use the magnetic pick-up from the overspeed group. Connect the wires from the magnetic pick-up to the overspeed switch and then connect wires from the speed switch to the 2301 Governor. The overspeed switch can be installed close to the 2301 Governor if needed.To reset overspeed switch, push in reset button for a moment.Power Takeoff Clutches
Clutch Adjustment
CLUTCH ADJUSTMENT
1. Clutch lever.1. Fasten a spring scale to the clutch lever at the distance, from the shaft center, shown in the chart.2. Look at the spring scale. Keep the angle between the scale and the lever at 90°. Pull the lever with the spring scale until the clutch engages. The pull needed to engage the clutch must be within the range given in the chart. 3. If the pull needed to engage the clutch is not within the range given, make an adjustment as follows:4. Remove the inspection plate from the clutch housing.5. Turn the clutch until lock pin (1 or 2) can be seen.6. Release push type lock pin (1) or pull type lock pin (2). Turn the adjustment ring and check the pull needed to engage the clutch again. Turn the adjustment ring clockwise, as seen from the rear of the clutch, to increase the pull needed. Turn it counterclockwise to decrease the pull needed.
CLUTCH ADJUSTMENT
1. Lock pin (push type). 2. Lock pin (pull type).Assembly Adjustments
End Play For Shaft Bearings
1. With dry bearings installed on the shaft install the shaft in the housing.2. Install the retainer. Tighten the retainer (nut or shim type) until 60 lb. in. (7 N m) is needed to keep the shaft in rotation.3. With shim type retainer measure the space between the retainer and the carrier. Add .013 in. (0.33 mm) to this measurement. Install this amount of shims between the retainer and the carrier. With nut type retainers turn it out the number of notches shown on the chart.4. Hit the output end of the clutch shaft with a soft hammer. This will cause the front bearing cup to move against the retainer. 5. Check the shaft end play with a dial indicator. If necessary add or subtract shims; or turn nut to get the correct end play.Hub Nut Installation
1. Tighten the hub nut to a torque of 30 lb. ft. (40 N m)2. Tighten the nut more according to

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts bucket Caterpillar catalog:

1882716 BUCKET AS-DIRT
216, 216B, 226B, 228, 232B, 236, 236B, 242B, 246C, 247, 247B, 248, 252B, 256C, 257B, 262C, 267, 267B, 268B, 272C, 277C, 279C, 287, 287C, 289C, 299C
2322759 BUCKET AS-HOE
307D, 308D, 416E, 416F, 420D, 420E, 420F, 430D, 430E, 430F
4203372 BUCKET AS-HEAVY DUTY
336D, 336D2, 345D, 345D L
1283779 BUCKET GP-HOE
416B, 416C, 416D, 420D, 422E, 424D, 426C, 428C, 428D, 428E, 432D, 432E, 434E, 436C, 438C, 442D, 442E, 444E
3453185 BUCKET & ADJUSTER GP
336D L, 345C, 349E L, 349E L VG
2322761 BUCKET AS-HOE
307D, 308D, 416E, 416F, 420D, 420E, 420F, 430D, 430E, 430F
1422568 BUCKET & ADJUSTER GP
320C, 325B L, 325C, 330B L
7Y7552 BUCKET AS
231D, 325 L, 325 LN, 330, 330 L
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.