AVSPARE.COM
parts catalog

BRACKET AS 9V8974 - Caterpillar



9V8974 BRACKET AS Caterpillar parts 916, 936, 950F, 966F, IT18B, IT28 BRACKET
Rating:
23
Alternative (cross code) number:
CA9V8974
9V-8974
9V8974
Caterpillar 9V8974 BRACKET AS
Weight: 5 pounds 2 kg.

Buy BRACKET AS 9V8974 Caterpillar genuine, new aftermarket tractor parts with delivery
INTEGRATED TOOLCARRIER, WHEEL LOADER,

Compatible equipment models: 9V8974:

INTEGRATED TOOLCARRIER  IT18B   IT28  
WHEEL LOADER  916   936   950F   966F   Caterpillar
Number on catalog scheme: 21
 
  For full view, you need register

Information:

Start By:a. remove fuel filter & base
At operating temperature, the engine coolant is hot and under pressure. The radiator and all lines to heaters or the engine contain hot water or steam. Any contact can cause severe burns. Look at the sight gauge to check the coolant level. The coolant level should be in the green range. If necessary, remove the fill cap only after the engine has been stopped and the cap is cool enough to remove with your bare hand. Remove the cooling system fill cap slowly to relieve pressure. Cooling system condition contains alkali that can cause personal injury. Avoid contact with the skin and eyes and do not drink. Allow cooling system components to cool before draining.
1. Drain the coolant from the engine in a suitable container for storage or disposal. Put identification on all lines, hoses and tubes for installation purposes. Cap and plug all lines, hoses and tubes to prevent foreign material from entering the system. 2. Remove bolts (1), washers and nuts that hold turbocharger tube (2) to the aftercooler housing. 3. Loosen clamps (3) on both sides of turbocharger tube (2). 4. Rotate turbocharger tube (2) out of the way. 5. Remove three bolts (5), washers and clips that hold wire assembly (4) and set wire assembly (4) out of the way.6. Install Tooling (A), lifting straps and a hoist to the aftercooler.7. Remove 11 bolts (6) and washers that hold the aftercooler and remove the aftercooler housing from the engine. The following steps are for installing the aftercooler housing.8. Install new O-ring seals on the aftercooler water inlet and outlet pipes. Lubricate the O-ring seals with clean engine oil. Put new gaskets in position on the cylinder head assembly.9. Fasten Tooling (A) and a hoist to the aftercooler housing, and put the aftercooler housing in position on the water pipes and cylinder head assembly.10. Put 9S3263 Thread Lock on the threads of the bolts, and install the bolts that hold the aftercooler housing to the cylinder head assembly.11. Rotate the turbocharger tube in position. Place a gasket between the aftercooler housing and adapter, and install four bolts and nuts that hold it. Tighten the turbocharger clamp nut to a torque of 18 3 N m (13 2 lb ft). Lightly hit all around the clamp with a soft faced hammer, and tighten the clamp nut again to the same torque value. Refer to the Topic "Lubricant Viscosities and Refill Capacities" in the Operation and Maintenance Manual for the proper filling procedure and the proper levels for the hydraulic system and the cooling system.End By:a. install fuel filter & base

Caterpillar parts catalog:

Caterpillar parts catalog
IT28 INTEGRATED TOOLCARRIER 8JB00001-UP (MACHINE) POWERED BY 3204 ENGINE
926 WHEEL LOADER 4NB00001-02075 (MACHINE) POWERED BY 3204 ENGINE
IT28 INTEGRATED TOOLCARRIER 8JB00001-UP (MACHINE) POWERED BY 3204 ENGINE
926 WHEEL LOADER 4NB00001-02075 (MACHINE) POWERED BY 3204 ENGINE
IT28B INTEGRATED TOOLCARRIER 5SD00001-UP (MACHINE) POWERED BY 3204 ENGINE
926E WHEEL LOADER 4NB02076-UP (MACHINE) POWERED BY 3204 ENGINE
IT28 INTEGRATED TOOLCARRIER 8JB00001-UP (MACHINE) POWERED BY 3204 ENGINE
926 WHEEL LOADER 4NB00001-02075 (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT28 INTEGRATED TOOLCARRIER 8JB00001-UP (MACHINE) POWERED BY 3204 ENGINE
926 WHEEL LOADER 4NB00001-02075 (MACHINE) POWERED BY 3204 ENGINE
IT28B INTEGRATED TOOLCARRIER 5SD00001-UP (MACHINE) POWERED BY 3204 ENGINE
926E WHEEL LOADER 4NB02076-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
950F Wheel Loader 6YG00001-UP (MACHINE) POWERED BY 3116 Engine
966F WHEEL LOADER 3XJ00001-UP (MACHINE) POWERED BY 3306 Engine
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
936 WHEEL LOADER 45Z00001-03056 (MACHINE) POWERED BY 3304 ENGINE
936E WHEEL LOADER 45Z03057-UP (MACHINE) POWERED BY 3304 ENGINE
916 WHEEL LOADER 9WB00001-UP (MACHINE) POWERED BY 3204 ENGINE
1T18 INTEGRATED TOOLCARRIER 7ZB00001-UP (MACHINE) POWERED BY 3204 ENGINE
IT18B INTEGRATED TOOLCARRIER 1DF00001-UP (MACHINE) POWERED BY 3204 ENGINE
936E WHEEL LOADER 45Z03057-UP (MACHINE) POWERED BY 3304 ENGINE


Parts bracket Caterpillar catalog:

6C0895 BRACKET
926A, 936, G936
6C0891 BRACKET
926A, 936, G936
9V6430 BRACKET
IT18, IT18B, IT28, IT28B
9V5926 BRACKET AS.
IT18, IT18B, IT28, IT28B
9V4672 BRACKET AS
926A, 936F, IT28
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.