AVSPARE.COM
parts catalog

COVER 9V9057 - Caterpillar



9V9057 COVER Caterpillar parts 508 COVER
Rating:
76
Alternative (cross code) number:
CA9V9057
9V-9057
9V9057
Caterpillar 9V9057 COVER
Weight: 1 pounds 0 kg.

Buy COVER 9V9057 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SKIDDER,

Compatible equipment models: 9V9057:

WHEEL SKIDDER  508   Caterpillar
Number on catalog scheme: 5
 
  For full view, you need register

Information:

Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1P-1855     Retaining Ring Pliers     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If any of the parts on the engine oil pump are worn or damaged, the entire pump must be replaced.
Note: If the No. 1 crankshaft main bearing cap was removed, install the No. 1 crankshaft main bearing cap with the engine oil pump. Tighten the bolts for the No. 1 crankshaft main bearing cap to a torque of 265 N m (195 lb ft).
If the shaft for the idler gear on the engine oil pump was removed, remove the excess Loctite 603. Apply a new layer of Loctite 603 to the bore in the main bearing cap and install the shaft.
Illustration 1 g00545972
Fill engine oil pump (7) with clean engine oil. Install engine oil pump (7) on the engine.
Install three bolts (6). Tighten the bolts to a torque of 22 N m (16 lb ft).
Illustration 2 g00545971
Install idler gear (5) .
Use Tool (A) to install retaining ring (4) .Note: After you install the engine oil pump and the idler gear, ensure that there is a minimum of 0.08 mm (.003 inch) backlash between the gear on the engine oil pump and the idler gear.
Install the engine oil relief valve. Refer to Disassembly and Assembly, "Engine Oil Relief Valve - Install".
Illustration 3 g00552238
Install the strainer, suction pipe (3), and the gasket.
Install bolt (2). Tighten the bolt to a torque of 22 N m (16 lb ft).
Install two bolts (1). Tighten the bolts to a torque of 22 N m (16 lb ft).End By: Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".

Caterpillar parts catalog:

Caterpillar parts catalog
508 SKIDDER AND GRAPPLE SKIDDER 2HD00001-UP (MACHINE) POWERED BY 3204 ENGINE


Parts cover Caterpillar catalog:

9G0004 COVER AS-TERMINAL
120G, 120H, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12K, 12M, 130G, 135H, 1390, 140G, 140H, 140K, 140K 2, 143H, 14H, 160G, 160H, 160K, 163H, 16H, 215, 215B, 2384C, 2484C, 24H, 24M, 2590, 30/30, 305.5, 3...
8N1725 COVER AS-TERMINAL
1090, 1190, 1190T, 120B, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140B, 140G, 140H, 140H ES, 1...
9M9439 COVER AS
120B, 12F, 16, 215, 215B, 225, 3114, 3116, 311C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2, 312E, 312E L, 315D L, 316E L, 318D2 L, 318E L, 319D L, 319D LN, 3208, 3304, 416B, 428B, 438B, 446B, 446D, ...
3G3718 COVER
508, 613C, 613C II, 65, 931, 931B, D3, D3B
4V5099 COVER
2470C, 2570C, 2670C, 2864C, 508, 533, 543, 553C, 563C, 573C, 586C, 814F, 814F II, 815B, 815F, 815F II, 816B, 816F, 816F II, 924K, 930K, 936, 936F, 938F, 938G, 938G II, 950B, 950B/950E, 950F, 950F II, ...
5V6180 COVER AS
508, 518, 936, D250B, D250E, D300B, D300D, G936
5V9360 COVER AS.
508, 926, G926, IT28, IT28B
7T4192 COVER
508, 517, D4HTSK II, D4HTSK III
3T7220 COVER
508, 517, D4HTSK II, D4HTSK III
7T4192 COVER
508, 517, D4HTSK II, D4HTSK III
3T7329 COVER AS
508, 517, D4HTSK II, D4HTSK III
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.