AVSPARE.COM
parts catalog

SHEET-RH 9V9220 - Caterpillar



9V9220 SHEET-RH Caterpillar parts 824C, 980C, 980F, 980F II SHEET
Rating:
23
Alternative (cross code) number:
CA9V9220
9V-9220
9V9220
Caterpillar 9V9220 SHEET-RH
Weight: 5 pounds 2 kg.

Buy SHEET-RH 9V9220 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL DOZER, WHEEL LOADER,

Compatible models Caterpillar: 9V9220:

WHEEL DOZER  824C  
WHEEL LOADER  980C   980F   980F II   Caterpillar
Number on catalog scheme: 14
 
  For full view, you need register

Information:

Start By:
Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft - Remove" for the correct procedure.
Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove" for the correct procedure. Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorised personnel that have the correct training.Before begining ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Use a deep socket in order to remove the electrical connections from the electronic unit injectors. Use of incorrect tooling will result in damage to the electronic unit injectors.
Note: Put identification marks on all hoses, on all hose assemblies, on wires and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. That helps to prevent fluid loss and plugging helps to keep contaminants from entering the system.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Illustration 1 g02475251
Place a suitable container below tube assembly (1) in order to catch any fuel that might be spilled.
Use a suitable tool in Position (X) in order to hold tube assembly (1) as nut on hose assembly (2) is loosened.
Loosen the nut on hose assembly (2) in order to allow the fuel to drain from tube assembly (1).
Remove hose assembly (2) from tube assembly (1). Remove O-ring seal (3) (not shown).
Use Tooling (C) in order to cap the hose assembly immediately. Use Tooling (C) in order to plug the tube assembly immediately.
Illustration 2 g01971773
Make a temporary mark on valve bridges (5) in order to show the location and orientation. Note: Identification will ensure that the valve bridges can be reinstalled in the original location and the original orientation.
Remove seal (4) from the cylinder head and electronic unit injector (8).
Make a temporary mark on wiring harness assembly (6) in order to show the location and orientation.
Use a deep socket to remove connections (7) from electronic unit injector (8).
Use Tooling (A) in order to remove Torx screw (9) from clamp (10). Discard the Torx screw.
Illustration 3 g01971775
Illustration 4 g01972153
Use Tooling (B) to pry beneath clamp (10) and free electronic unit injector (8) from the cylinder

Caterpillar parts catalog:

Caterpillar parts catalog
824C TRACTOR 85X00001-01193 (MACHINE) POWERED BY 3406 ENGINE
824C TRACTOR 85X01194-UP (MACHINE) POWERED BY 3406 ENGINE
980C Wheel Loader 63X06575-UP (MACHINE) POWERED BY 3406 Engine
980F Wheel Loader 8CJ00001-UP (MACHINE) POWERED BY 3406 Engine


Parts sheet Caterpillar catalog:

8R4189 SHEET
980C, 980F, 980F II
6W8355 SHEET
824C, 824G, 824G II, 824H, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 980C, 980F, 980F II, 980G
6W5140 SHEET
824C, 826C, 980C, 980F
6W5225 SHEET
980C, 980F, 980F II
7V3612 SHEET AS
815B, 826C, 950B, 950F, 950F II, 966D, 966F, 966F II, 980C, 980F, 980F II
2V9350 SHEET AS
834B, 836, 988B
9V9225 SHEET-LH
824C, 980C, 980F, 980F II
9V9221 SHEET-RH
824C, 980C, 980F, 980F II
9V9226 SHEET-LH
824C, 980C, 980F, 980F II
9V9223 SHEET-RH
824C, 980C, 980F, 980F II
9V9227 SHEET-LH
824C, 980C, 980F, 980F II
7V2199 SHEET AS
824C, 825C, 826C, 980C, 980F, 980F II
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.