AVSPARE.COM
parts catalog

PLATE 9V9263 - Caterpillar



9V9263 PLATE Caterpillar parts 508 PLATE
Rating:
54
Alternative (cross code) number:
CA9V9263
9V-9263
9V9263
Caterpillar 9V9263 PLATE
Weight: 0.25 pounds 0 kg.

Buy PLATE 9V9263 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SKIDDER,

Compatible equipment models: 9V9263:

WHEEL SKIDDER  508   Caterpillar
Number on catalog scheme: 12
 
  For full view, you need register

Information:

Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     8S-7640     Stand     2    
8S-7611 Tube     2    
8S-7615 Pin     2    
B     5W-5332     Lug     2    
C     8S-9906     Ratchet Puller     1    
D     5W-1400     Washer     2    
5W-4650 Nut     2    
Follow the recommended procedure for removal and installation of tires and or wheel assemblies.Ensure that the machine and tire and or wheel assembly are properly supported at all times.Improper procedures that are used to remove and install tires and or wheel assemblies can result in personal injury or death.
Note: Tires must be inflated inside a protective cage prior to mounting on the machine.
Make sure that the tires, the wheel hub, the rim, the lug nuts, and the washers are thoroughly clean prior to installation.
Illustration 1 g00637061
Check the condition of lug bolts (7) . Check the condition of spacer rings (6) . If any of the parts are worn or damaged, use new parts for replacement.
Install a spacer ring (6) on each lug bolt (7) , as shown.
Install Tooling (B) on two of the lug bolts in the positions that are shown.
Illustration 2 g00637052
Fasten a lifting strap to inner tire and rim (5) , as shown. Fasten an appropriate lifting device to the lifting strap. Install the inner tire and rim on the front axle, as shown. The weight of the inner tire and rim is approximately 93 kg (205 lb).
Make sure that inner tire and rim (5) is against the hub of the axle. Remove the lifting strap.
Illustration 3 g00637050
Fasten a lifting strap to tire ring (3) . Fasten an appropriate lifting device to the lifting strap. Position the tire ring against the inner tire and rim. The weight of the tire ring is approximately 32 kg (70 lb).
Make sure that the tire ring is centered on the tire.Note: Align the bolt holes for two screws (2) on the outer tire and rim with the bolt holes for two screws (2) on the inner tire and rim.
Illustration 4 g00637303
Position the forks of a lift truck beneath outer tire and rim (4) . Use Tooling (C) to secure the outer tire and rim to the lift truck. The weight of the outer tire and rim is approximately 93 kg (205 lb).
Install outer tire and rim (4) on the front axle.
Make sure that tire ring (3) is centered. Make sure that the tire ring is against the inner tire and rim. Make sure that the outer tire and rim is against the tire ring.
Illustration 5 g00637352
Install Tooling (D) , as shown. Remove Tooling (B) .
Illustration 6 g00637361
Install two screws (2) .
Install eight lug nuts (1) . Remove Tooling (D) . Install remaining two lug nuts (1) . Tighten the lug nuts to a torque of 350 3 N m (258 2 lb ft).
Remove the lifting strap from tire ring (3) .
Illustration

Caterpillar parts catalog:

Caterpillar parts catalog
508 SKIDDER AND GRAPPLE SKIDDER 2HD00001-UP (MACHINE) POWERED BY 3204 ENGINE


Parts plate Caterpillar catalog:

3N3790 PLATE-SERIAL NUMBER- INSTALL IN CAST PAD
1140, 1145, 1150, 1160, 120G, 120H NA, 12G, 12H, 12H ES, 12H NA, 12M 3, 12M 3 AWD, 130G, 140G, 140H, 140H ES, 140H NA, 140M 3, 140M 3 AWD, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 16...
3G5980 PLATE
153, 416, 416B, 426B, 428, 428B, 438B, 446, 446B, 446D, 508, 515, 518, 518C, 525, 525B, 525C, 528, 535B, 535C, 539, 545, 545C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 824C, 826C, 916,...
6H5139 PLATE-PRESSURE
120G, 12F, 12G, 130G, 140, 141, 14E, 14G, 153, 16, 163, 16G, 172, 173B, 183, 183B, 184, 191, 193, 30/30, 416, 416B, 426B, 428, 428B, 438B, 446, 46, 508, 515, 517, 518, 525, 525D, 527, 528, 535D, 545D,...
6Y5631 PLATE-CLUTCH
446, 446B, 508, 517, 910E, 918F, 924F, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, D4HTSK II, D4HTSK III, IT12B, IT14B, IT14F, IT18F, IT24F, IT28G, RT100
4V0612 PLATE
10-20B, 140M, 160M, 215, 236D, 242B3, 242D, 246C, 246D, 256C, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 272C, 272D, 272D XHP, 277C, 277C2, 277D, 279C, 279C2, 279D, 287C, 287C2, 287D, 289C, 289C2, 2...
5P8197 PLATE-WARNING
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H, 16H NA, 215, 215B, 2...
2K0714 PLATE
508, 814, 815, 816, 936, 950, 950B, 950B/950E, 966C, 966D, 966F, 966G, 966R, G936
3T7322 PLATE
508, 517, D4HTSK II, D4HTSK III
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.