AVSPARE.COM
parts catalog

BRACKET AS 9V9264 - Caterpillar



9V9264 BRACKET AS Caterpillar parts 508 BRACKET
Rating:
45
Alternative (cross code) number:
CA9V9264
9V-9264
9V9264
Caterpillar 9V9264 BRACKET AS
Weight: 1 pounds 0 kg.

Buy BRACKET AS 9V9264 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SKIDDER,

Compatible equipment models: 9V9264:

WHEEL SKIDDER  508   Caterpillar
Number on catalog scheme: 17
 
  For full view, you need register

Information:

Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-5518 Bearing Tool 1
B 8T-5096 Dial Indicator Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Place clean engine oil on the crankshaft main bearings prior to assembly. Ensure that the tabs on the back side of the crankshaft main bearings fit in the grooves of the crankshaft main bearing caps and the cylinder block.
Illustration 1 g01153704
Use Tooling (A) and install the upper halves of the crankshaft main bearings in the cylinder block. Do not put oil on the back of the crankshaft main bearing.
Install the lower halves of the crankshaft main bearings in crankshaft main bearing caps (2). Do not put oil on the back of the crankshaft main bearing.
Crankshaft main bearing caps should be installed with the part number toward the front of the engine. Crankshaft main bearing caps are to be identified by stamped numbers 1 through 7 that are located on the bottom surface of the bearing cap. The thrust plate is used on the number 6 main bearing.
Place crankshaft main bearing caps (2) in position on the cylinder block. Place clean engine oil or Molylube on the bolt threads and the washer face. Install bolts (1).
Tighten each bolt (1) to a torque of 95 5 N m (70 4 lb ft). Tighten each bolt (1) for an additional 90 5 degrees (1/4 turn).
Check the end play of the crankshaft with Tooling (B). The end play must be 0.21 - 0.60 mm (0.008 - 0.024 inch). End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".

Caterpillar parts catalog:

Caterpillar parts catalog
508 SKIDDER AND GRAPPLE SKIDDER 2HD00001-UP (MACHINE) POWERED BY 3204 ENGINE


Parts bracket Caterpillar catalog:

9K0974 BRACKET
1090, 1190, 1190T, 1290T, 508, 515, 525, 525B, 525C, 525D, 528, 528B, 530B, 533, 535B, 535C, 535D, 543, 545, 545C, 545D, 555D, 943, HA770, HA771, HA870, HA871, TK1051, TK370, TK371, TK380, TK381, TK71...
2T1098 BRACKET
508, 613C, 613C II, 773D, 773E, 775E, 776D, 777D, 793F
4I4767 BRACKET AS
325, 325 L, 325 LN
4I6835 BRACKET AS
325, 325 L, 325 LN
4I4766 BRACKET AS
325, 325 L, 325 LN
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.