ADAPTER-TEE 3089568 - Caterpillar

Do not use rectangular seals in hoses or tubes when the wall thickness around the O.D. (outside diameter) of the groove is less than 3.2 mm (.13 inch).
Hydraulic Filters
Oil mixed with water/glycol fluid causes a sludge (increase viscosity) that will not flow through the filter elements. To adapt to this condition, a plastic filter element is used in the implement circuit in place of paper filter elements. Refer to the following chart. With the new elements, filter change interval is extended to 500 service hours. Refer to the Operation, Lubrication and Maintenance of Fire Resistant Fluid Hydraulic System, SEBU5204.
Use standard element assemblies in all steering and pilot system filter housings (except on the 992). Change all paper oil filter elements every 50 service hours or after one week. Check the condition of removed filter elements and make the filter change interval shorter if the elements get too dirty during the interval used.
Table 6
Filter Element Part Numbers
Standard (For Petroleum Oil) Fire Resistant Fluid (Water/Glycol)
4J816 4T3130
9M9740 4T3131
4J6064 4T3132
7J670 4T3133
9J5461 4T3134
4T0522 1R0735 104-6931
Modification of the 910, 931, 941, 951 hydraulic filter retainer, adapter, and spacer is necessary before the new type element can be installed. 910, 931 Filter Modification
Illustration 2 g00546274
(1) 9J-1307 Retainer
(2) Adapter
(3) Filter element
(A) 45 mm 0.25 mm (1.75 inch .01 inch)
(B) 79 mm (3.12 inch)
(C) 68 mm (2.69 inch)
(D) 51 mm (2.0 inch)
(E) 71 mm (2.80 inch)
(F) 52 mm (2.03 inch)
(G) 38 mm (1.25 inch)
(H) 9.6 mm (.38 inch)
(I) 60 mm (2.38 inch)
(J) 67 mm (2.63 inch)
Make modification of former 9J-1307 Retainer (1) to the dimension shown. Make a new adapter (2), as shown from a mild (medium) type steel. Install retainer (1), new filter element (3) and new adapter (2) into the filter housing, as shown. 941, 951 Filter Modification
Illustration 3 g00546273
(1) Spacer
(2) Adapter
(3) Filter element
(4) 11 mm (.422 inch) Hole
(A) 57 mm (12.25 inch)
(B) 44 mm (1.75 inch)
(C) 4 mm (.156 inch)
(D) 1.5 mm (.06 inch)
(E) 17 mm (.87 inch)
(F) 31 mm (1.22 inch)
(G) 44 mm (1.75 inch)
(H) 41 mm (1.62 inch)
(I) 47 mm (1.88 inch)
(J) 57 mm (2.26 inch)
(K) 41 mm (1.62 inch)
(L) 44 mm (1.75 inch)
(M) 4 mm (.156 inch)
Make one spacer (1) and drill eight 11 mm (.422 inch) holes (4) evenly spaced, as shown. Make two adapters (2), as shown. Install adapters (2) and two new filter elements (3) into the filter housing, as shown. Brake Slack Adjuster (If equipped)
Illustration 4 g00546275
(1) 5H-5672 Seal
(2) 4F-7387 Seal
(3) 8S-5790 Seal
(4) Brake slack adjuster
Remove seals (1), (2), and (3) from brake slack adjuster (4). Install a new 5H-5672 Seal at location (1), 4F-7387 Seal at location (2) and a 8S-5790 Seal at location (3), as shown.