2964700 BODY AS Caterpillar parts
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318D L, 319D, 319D L, 319D LN
Rating:
Alternative (cross code) number:
CA2964700
296-4700
2964700
CA2964700
296-4700
2964700
Weight: 48 pounds 21 kg.
EXCAVATOR,
Compatible equipment models: 2964700:
Number on catalog scheme:
27
For full view, you need register
Information:
Walk-Around Inspection
For any type of leak, clean up the fluid. If leaking is observed, find the source and correct the leak. If leaking is suspected, check the fluid levels more often than recommended until the leak is found or fixed, or until the suspicion of a leak is proved to be unwarranted.
To obtain maximum service life for your engine, make a thorough inspection before starting the engine. Make a walk-around inspection of the installation. Look for items such as oil or coolant leaks, loose bolts, and trash buildup. Remove any trash. Make repairs, if necessary.
The guards must be in the proper place. Repair damaged guards or replace missing guards.
Ensure that the areas around the rotating parts are clear.Air Inlet System
Unburned gas in the air inlet and exhaust system may ignite when the engine is started. Personal injury and/or property damage may result.Before starting an engine that may contain unburned gas, purge the unburned gas from the air inlet and exhaust system. Refer to the topic on purging unburned gas in the "Starting the Engine" section.
Ensure that the air inlet piping and the air filters are in place and clean.
Ensure that all clamps and connections are secure.
Inspect the air cleaner service indicator (if equipped). Service the air cleaner filter element when the yellow diaphragm enters the red zone, or the red piston locks in the visible position.Cooling System
Inspect the cooling system for leaks or loose connections. Inspect the condition of all the hoses and pipes for the cooling system. Ensure that the connections are properly clamped.
Inspect the water pumps for evidence of leaks.
Check the coolant level. Add coolant, if necessary. For information on the proper coolant to use, see this Operation and Maintenance Manual, "Fluid Recommendations" (Maintenance Section). For information on the amount of coolant to use, see this Operation and Maintenance Manual, "Refill Capacities" (Maintenance Section).Driven Equipment
If necessary, check the oil levels of the driven equipment. Perform any maintenance that is required for the driven equipment. Refer to the literature that is provided by the OEM of the driven equipment.
If the engine is equipped with a clutch, ensure that the clutch is disengaged.
For generator set engines, ensure that the main circuit breaker is open.Electrical System
Inspect the wiring for the following conditions:
Loose connections
Wiring that is worn or frayedInspect the gauge panel and the control panel for good condition. Reset any shutoff or alarm components.Fuel System
NEVER use a flame to check for gas leaks. Use a gas detector.An open flame can ignite mixtures of air and fuel. This will cause explosion and/or fire which could result in severe personal injury or death.
Check the fuel lines for leaks with a gas detector.
Inspect the fuel lines for loose fittings and leaks. Ensure that the fuel lines are properly clamped.
Ensure that the fuel is supplied to the engine at the correct pressure for the engine.Lubrication System
Illustration 1 g00760044
Oil level gauge (dipstick) (1) "ADD" mark (2) "FULL" mark
Excessive engine oil will increase oil consumption and result in excessive deposits in the combustion chamber. Do not
For any type of leak, clean up the fluid. If leaking is observed, find the source and correct the leak. If leaking is suspected, check the fluid levels more often than recommended until the leak is found or fixed, or until the suspicion of a leak is proved to be unwarranted.
To obtain maximum service life for your engine, make a thorough inspection before starting the engine. Make a walk-around inspection of the installation. Look for items such as oil or coolant leaks, loose bolts, and trash buildup. Remove any trash. Make repairs, if necessary.
The guards must be in the proper place. Repair damaged guards or replace missing guards.
Ensure that the areas around the rotating parts are clear.Air Inlet System
Unburned gas in the air inlet and exhaust system may ignite when the engine is started. Personal injury and/or property damage may result.Before starting an engine that may contain unburned gas, purge the unburned gas from the air inlet and exhaust system. Refer to the topic on purging unburned gas in the "Starting the Engine" section.
Ensure that the air inlet piping and the air filters are in place and clean.
Ensure that all clamps and connections are secure.
Inspect the air cleaner service indicator (if equipped). Service the air cleaner filter element when the yellow diaphragm enters the red zone, or the red piston locks in the visible position.Cooling System
Inspect the cooling system for leaks or loose connections. Inspect the condition of all the hoses and pipes for the cooling system. Ensure that the connections are properly clamped.
Inspect the water pumps for evidence of leaks.
Check the coolant level. Add coolant, if necessary. For information on the proper coolant to use, see this Operation and Maintenance Manual, "Fluid Recommendations" (Maintenance Section). For information on the amount of coolant to use, see this Operation and Maintenance Manual, "Refill Capacities" (Maintenance Section).Driven Equipment
If necessary, check the oil levels of the driven equipment. Perform any maintenance that is required for the driven equipment. Refer to the literature that is provided by the OEM of the driven equipment.
If the engine is equipped with a clutch, ensure that the clutch is disengaged.
For generator set engines, ensure that the main circuit breaker is open.Electrical System
Inspect the wiring for the following conditions:
Loose connections
Wiring that is worn or frayedInspect the gauge panel and the control panel for good condition. Reset any shutoff or alarm components.Fuel System
NEVER use a flame to check for gas leaks. Use a gas detector.An open flame can ignite mixtures of air and fuel. This will cause explosion and/or fire which could result in severe personal injury or death.
Check the fuel lines for leaks with a gas detector.
Inspect the fuel lines for loose fittings and leaks. Ensure that the fuel lines are properly clamped.
Ensure that the fuel is supplied to the engine at the correct pressure for the engine.Lubrication System
Illustration 1 g00760044
Oil level gauge (dipstick) (1) "ADD" mark (2) "FULL" mark
Excessive engine oil will increase oil consumption and result in excessive deposits in the combustion chamber. Do not
Caterpillar parts catalog:
Parts body Caterpillar catalog:
2178580
BODY-VALVE
315C, 315D L, 318C, 319C, 319D, 319D LN
315C, 315D L, 318C, 319C, 319D, 319D LN
2178582
BODY-VALVE
315C, 315D L, 318C, 319C, 319D, 319D L, 319D LN
315C, 315D L, 318C, 319C, 319D, 319D L, 319D LN
3640980
BODY
315D L, 316E L, 318D L
315D L, 316E L, 318D L
2821541
BODY AS-VALVE
319D, 319D LN
319D, 319D LN
6I6905
BODY
319D, 319D L, 319D LN, 320 L, 320B, 320C, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 323D L, 323D LN, 323D SA, 324D, 324D L, 324D LN, 325, 325B, 325B L, 325C, 325D, 325D L, 329D L, 329D LN, 3...
319D, 319D L, 319D LN, 320 L, 320B, 320C, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 323D L, 323D LN, 323D SA, 324D, 324D L, 324D LN, 325, 325B, 325B L, 325C, 325D, 325D L, 329D L, 329D LN, 3...
2983255
BODY
312D, 323D L, 323D LN
312D, 323D L, 323D LN
3727596
BODY AS
311D LRR
311D LRR
3727597
BODY AS
311D LRR
311D LRR
3783459
BODY
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312E, 312E L, 313D, 314D CR, 314D LCR, 314E CR, 314E LCR
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312E, 312E L, 313D, 314D CR, 314D LCR, 314E CR, 314E LCR
3077912
BODY AS
311D LRR
311D LRR
2S5011
BODY-FUSE HOLDER
120, 120G, 12E, 12F, 12G, 130G, 140, 14E, 14G, 16, 16G, 235, 315D L, 561D, 571G, 572G, 583K, 594H, 613, 621, 621B, 623, 627, 627B, 631C, 633C, 637D, 641B, 650B, 657B, 666B, 776, 777, 777G, 785D, 834, ...
120, 120G, 12E, 12F, 12G, 130G, 140, 14E, 14G, 16, 16G, 235, 315D L, 561D, 571G, 572G, 583K, 594H, 613, 621, 621B, 623, 627, 627B, 631C, 633C, 637D, 641B, 650B, 657B, 666B, 776, 777, 777G, 785D, 834, ...
7K0615
BODY-COUPLING
115, 315D L, 63, H140CS
115, 315D L, 63, H140CS
3502895
BODY-CASING
307D, 308D, 308E, 308E CR, 308E SR
307D, 308D, 308E, 308E CR, 308E SR
3099248
BODY AS
304C CR, 305D CR, 305E
304C CR, 305D CR, 305E
1988171
BODY
303.5C, 303C CR, 304C CR, 305C CR
303.5C, 303C CR, 304C CR, 305C CR
2637015
BODY AS
305.5
305.5
2400124
BODY AS
301.6C, 302.5C, D3K XL, D3K2 LGP, D4K XL, D4K2 XL, D5K LGP, D5K2 XL
301.6C, 302.5C, D3K XL, D3K2 LGP, D4K XL, D4K2 XL, D5K LGP, D5K2 XL
2528985
BODY
M313C, M313D, M315D 2
M313C, M313D, M315D 2
3727596
BODY AS
311D LRR
311D LRR
2983255
BODY
312D, 323D L, 323D LN
312D, 323D L, 323D LN
3065883
BODY-VALVE
M313D, M315D, M316D, M318D, M318D MH, M322D, M322D MH
M313D, M315D, M316D, M318D, M318D MH, M322D, M322D MH
6I6905
BODY
319D, 319D L, 319D LN, 320 L, 320B, 320C, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 323D L, 323D LN, 323D SA, 324D, 324D L, 324D LN, 325, 325B, 325B L, 325C, 325D, 325D L, 329D L, 329D LN, 3...
319D, 319D L, 319D LN, 320 L, 320B, 320C, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 323D L, 323D LN, 323D SA, 324D, 324D L, 324D LN, 325, 325B, 325B L, 325C, 325D, 325D L, 329D L, 329D LN, 3...
2821541
BODY AS-VALVE
319D, 319D LN
319D, 319D LN
3640980
BODY
315D L, 316E L, 318D L
315D L, 316E L, 318D L