BRACKET AS 4308202 - Caterpillar

Illustration 35 g03735257
Notice that the "Return to Dig" feature is not installed. In the configuration screen, double-click on the "Return to Dig Feature Installation Status" link, as shown in Illustration 35.
In the Pop-up window, change the New Value field from "Not Installed" to "Installed" on the drop-down menu. Click "OK".
Access the CAT Factory Password System (FPS) at https://fps.cat.com on the pop-up window that appears to obtain the required passwords. Refer to "Machine Configuration" Illustration 32.
Enter the passwords into the fields labeled "Factory Password #1" and "Factory Password #2".
Turn the start key to the OFF position and wait at least 30 seconds. Turn the start key back to the ON position. The new feature will be activated on the next power cycle.
Repeat Step 3 and ensure that all the Self-Level features are installed.Appendix A: Assembly Procedure for the 422-3183 Sensor and Mounting Gp.
Illustration 36 g03735280
(17) 422-3182 Sensor Link As.
(18) 421-0128 Bracket As.
(4) 8T-4224 Hard Washer
(19) 5C-7261 Nut
Insert either end of 422-3182 Sensor Link As. (17) onto the shorter bent side of the 421-0128 Bracket As. (18) and secure using one 8T-4224 Hard Washer (4) and one 5C-7261 Nut (19). Tighten the Nut to 15 3 N m (11 2.2 lb ft). Refer to Illustration 36.
Illustration 37 g03735289
(18) 421-0128 Bracket As.
(20) 266-2337 Position Sensor Gp
(21) 5H-3182 Spring Pin
Applying excessive force to the Position Sensor shaft while inserting the Pin can cause the shaft to be damaged. Care must be taken to support the bracket assembly while inserting the pin. Pin may also be driven with a mallet, but driving the pin is not recommended
Insert the other end of 421-0128 Bracket As. (18) onto the shaft on the 266-2337 Position Sensor Gp (20) as shown in Illustration 37. Insert 5H-3182 Spring Pin (21) into the driver on the Bracket As (18) and through the shaft of the Position Sensor (20).
Illustration 38 g03735309
(17) 422-3182 Sensor Link As.
(4) 8T-4224 Hard Washer
(19) 5C-7261 Nut
(22) 422-3175 Bracket
Insert 422-3175 Bracket (22) to the free end of 422-3182 Sensor Link As. (17) as shown in Illustration 38. Secure using one 8T-4224 Hard Washer (4) and one 5C-7261 Nut (19). Tighten the Nut to 15 3 N m (11 3 lb ft).
Illustration 39 g03735316
(4) 8T-4224 Hard Washers
(19) 5C-7261 Nuts
(20) 266-2337 Position Sensor Gp
(14) 421-0131 Bracket
(23) 8T-4197 Bolts
Install 421-0131 Bracket (14) onto the back of 266-2337 Position Sensor Gp (20) with the flange of Bracket (14) oriented as shown in Illustration 39. Secure the Bracket using five 8T-4197 Bolts (23) and five 8T-4224 Hard Washers (4) on one side, and five 5C-7261 Nuts (19) and five 8T-4224 Hard Washers (4) on the opposite side. Insert the Bolts in the direction shown in Illustration 39.