9V8482 BUMPER AS-RH Caterpillar parts
980C, 980F, 980F II
Rating:
Alternative (cross code) number:
CA9V8482
9V-8482
9V8482
CA9V8482
9V-8482
9V8482
Weight: 215 pounds 97 kg.
WHEEL LOADER,
This part in 2 request:
Show.
This information for suppliers only!
2018-02-19
2018-02-19
Number on catalog scheme:
32
For full view, you need register
Information:
Removal Procedure
Start By:
Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the correct procedure.
Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove" for the correct procedure.
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove" for the correct procedure.
If the engine has an accessory drive, remove the accessory drive. Refer to Disassembly and Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove" for the correct procedure.
Remove the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) - Remove and Install" for the correct procedure.
Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02490356
Slide locking tab (1) (not shown) into the unlocked position.
Disconnect harness assembly (2) from coolant temperature sensor (3).
Cut cable strap (4) and remove harness assembly (2) from bypass tube (5).
Remove bolts (6) that secure bypass tube (5) to front housing (7).
Remove bypass tube (5) from the cylinder head. Remove O-ring seal (8) and O-ring seal (9) from bypass tube (5).
Illustration 2 g02490357
Remove bolts (11), bolts (12) and bolts (13) from front housing (7). Note: The bolts are three different lengths. Note the positions of the bolts of different length.
Remove front housing (7) from the cylinder block.
Remove gasket (14).
If necessary, follow Step 9.a through Step 9.b in order to remove bearing (10) from housing (7).
Place housing (7) onto a suitable support.
Use a suitable tool in order to press bearing (10) out of housing (7).
Illustration 3 g02490358
Remove thrust washer (15) from cylinder block (16).
Start By:
Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the correct procedure.
Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove" for the correct procedure.
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove" for the correct procedure.
If the engine has an accessory drive, remove the accessory drive. Refer to Disassembly and Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove" for the correct procedure.
Remove the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) - Remove and Install" for the correct procedure.
Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02490356
Slide locking tab (1) (not shown) into the unlocked position.
Disconnect harness assembly (2) from coolant temperature sensor (3).
Cut cable strap (4) and remove harness assembly (2) from bypass tube (5).
Remove bolts (6) that secure bypass tube (5) to front housing (7).
Remove bypass tube (5) from the cylinder head. Remove O-ring seal (8) and O-ring seal (9) from bypass tube (5).
Illustration 2 g02490357
Remove bolts (11), bolts (12) and bolts (13) from front housing (7). Note: The bolts are three different lengths. Note the positions of the bolts of different length.
Remove front housing (7) from the cylinder block.
Remove gasket (14).
If necessary, follow Step 9.a through Step 9.b in order to remove bearing (10) from housing (7).
Place housing (7) onto a suitable support.
Use a suitable tool in order to press bearing (10) out of housing (7).
Illustration 3 g02490358
Remove thrust washer (15) from cylinder block (16).
Caterpillar parts catalog:
Parts bumper Caterpillar catalog:
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 242B, 242B3, 247, ...
0667948
BUMPER-RUBBER
3116, 3208, 3406, 3406B, 3406C, 3406E, 980C
3116, 3208, 3406, 3406B, 3406C, 3406E, 980C
5V3854
BUMPER
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 311C, 315B FM L, 320B FM LL, 322 FM L, 322 LN, 322B L, 324D L, 325, 325 L, 325B L, 330, 330 FM L, 330 L, 330B L, 330D, 330D FM, 330D L, 33...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 311C, 315B FM L, 320B FM LL, 322 FM L, 322 LN, 322B L, 324D L, 325, 325 L, 325B L, 330, 330 FM L, 330 L, 330B L, 330D, 330D FM, 330D L, 33...
4V8555
BUMPER
589, 768C, 785, 815B, 826C, 834B, 910, 916, 918F, 920, 936, 950B, 950F II, 955L, 963, 973, 980C, 988B, 992C, CP-433C, CP-563, CS-431C, CS-433C, CS-531C, CS-533C, CS-563C, CS-573C, CS-583C, D4HTSK III,...
589, 768C, 785, 815B, 826C, 834B, 910, 916, 918F, 920, 936, 950B, 950F II, 955L, 963, 973, 980C, 988B, 992C, CP-433C, CP-563, CS-431C, CS-433C, CS-531C, CS-533C, CS-563C, CS-573C, CS-583C, D4HTSK III,...
8V7010
BUMPER
554, 574, 574B, 814B, 815B, 824C, 826C, 844, 844H, 854G, 854K, 966D, 966F, 980C, 980F, 980F II, 990, 990 II, 990H, 992G, 992K, 994F
554, 574, 574B, 814B, 815B, 824C, 826C, 844, 844H, 854G, 854K, 966D, 966F, 980C, 980F, 980F II, 990, 990 II, 990H, 992G, 992K, 994F
9V8483
BUMPER AS-LH
980C, 980F, 980F II
980C, 980F, 980F II
3V6245
BUMPER ASSEM.
980C
980C
3V6246
BUMPER ASSEM.
980C
980C
5V6078
BUMPER AS-LH
980C
980C
5V6077
BUMPER AS-RH
980C
980C
6C2958
BUMPER AS-RH
980C, 980F
980C, 980F
6C2957
BUMPER AS-LH
980C, 980F
980C, 980F
9V8483
BUMPER AS-LH
980C, 980F, 980F II
980C, 980F, 980F II
8R0914
BUMPER AS
834B, 988B
834B, 988B
8V0123
BUMPER AS
834B, 988B
834B, 988B
7V5618
BUMPER AS
992C
992C
7V0616
BUMPER AS
992C
992C
9C2265
BUMPER AS
992C, 992D
992C, 992D
6C3994
BUMPER
950F
950F
1199027
BUMPER
960F, 966F, 966F II, 970F
960F, 966F, 966F II, 970F
5V8280
BUMPER AS
966D, 966F
966D, 966F
8X3150
BUMPER AS
994
994
1699071
BUMPER AS
994, 994D
994, 994D
8X8632
BUMPER AS
994
994