1232020 BUSHING Caterpillar parts
320B, 320B U, 321B, 322B, 322B L, 322B LN, 325B, 325B L, 330, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 345B, 345B II, 345B II MH, 345B L, W330B, W345B II
Rating:
Alternative (cross code) number:
CA1232020
123-2020
1232020
CA1232020
123-2020
1232020
Weight: 0.01 pounds 0 kg.
Information:
ID
3
mm
MATERIAL THICKNESS
11.5
mm
OD
8
mm
EXCAVATOR, WHEELED EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$41.53
19 Jul 2018
185 Hundredths Pounds
GMB: GMB
GMB 123-2020 OE Replacement Water Pump with Gasket
Factory sealed, precision ground, one piece bearing assembly || High-flow design for long-lasting, efficient cooling || Designed for Original Equipment (OE) fit and performance || Precision-ground shaft and hub accept OE fan clutches perfectly || Unique no-sealant required gasket makes installation fast, easy and leak-free || Designed for OE fit and performance || Unique no-sealant required, gasket makes installation fast, easy and leak-free
Factory sealed, precision ground, one piece bearing assembly || High-flow design for long-lasting, efficient cooling || Designed for Original Equipment (OE) fit and performance || Precision-ground shaft and hub accept OE fan clutches perfectly || Unique no-sealant required gasket makes installation fast, easy and leak-free || Designed for OE fit and performance || Unique no-sealant required, gasket makes installation fast, easy and leak-free
Number on catalog scheme:
20
For full view, you need register
Compatible equipment models: 1232020:
Information:
Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00955826
Typical example
Inspect the fuel injection lines (1) for wear and for damage. Replace any fuel injection line (1) that is worn or any fuel injection line that is damaged.
Loosely install the clamps for the fuel injection lines (1).
Remove the dust caps from the fuel injection pump (3) and from the fuel injectors (2). Remove the dust caps from the fuel injection lines (1).
Loosely connect the nuts at both ends of the fuel injection lines (1).
Ensure that each fuel injection line (1) does not contact any other fuel injection line or any other engine component. Tighten the fasteners for the clamps for the fuel injection lines (1). Check that the fuel injection lines (1) are still clear of other components.
Tighten the fuel injection lines (1) at the fuel injectors (2) to a torque of 30 N m (22 lb ft).
Tighten the fuel injection lines (1) at the fuel injection pump (3) to 30 N m (22 lb ft).
Remove the air from the fuel system. Refer to the Operations and Maintenance Manual, "Fuel System - Prime". End By:
If equipped, install the cover for the fuel injectors. Refer to this Disassembly and Assembly Manual, "Fuel Injector Cover - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00955826
Typical example
Inspect the fuel injection lines (1) for wear and for damage. Replace any fuel injection line (1) that is worn or any fuel injection line that is damaged.
Loosely install the clamps for the fuel injection lines (1).
Remove the dust caps from the fuel injection pump (3) and from the fuel injectors (2). Remove the dust caps from the fuel injection lines (1).
Loosely connect the nuts at both ends of the fuel injection lines (1).
Ensure that each fuel injection line (1) does not contact any other fuel injection line or any other engine component. Tighten the fasteners for the clamps for the fuel injection lines (1). Check that the fuel injection lines (1) are still clear of other components.
Tighten the fuel injection lines (1) at the fuel injectors (2) to a torque of 30 N m (22 lb ft).
Tighten the fuel injection lines (1) at the fuel injection pump (3) to 30 N m (22 lb ft).
Remove the air from the fuel system. Refer to the Operations and Maintenance Manual, "Fuel System - Prime". End By:
If equipped, install the cover for the fuel injectors. Refer to this Disassembly and Assembly Manual, "Fuel Injector Cover - Remove and Install".
Caterpillar parts catalog:
Parts bushing Caterpillar catalog:
324D, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345B II, 345B II MH, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 34...
330, 330 FM L, 330 L, 350, E300B, OEMS
345B II, 345B L, P115, S115, VPC-30, VPS-35
325C, 330C, 330C FM, 330C L, 330D L
330C, 330C FM, 330C L
345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 350, 365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L, 385C
330, 330 FM L, 330 L, 330B L
330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L
325C FM, 325D FM, 325D FM LL, 330 L, 330B, 330B L, M325C MH, M325D L MH
345B II, 345B II MH, 345B L, 345C, 365B, W345B II
330C, 330C L, 345B II, 345B L
330C, 330C L
320B, 320N, 322B, 322B L, 322B LN, 322C, 322C FM, 325, 325 L, 325 LN, 325B, 325B L, 325C, 330, 330B, 330B L, 385B, 385C, 385C L, 390D, 390D L, 390F L, G107B, TK1051
6Y0849
BUSHING-TRACK
320B, 322 FM L, 322B L, 325, 325 L, 325 LN, 325B, 325B L, OEMS
320B, 322 FM L, 322B L, 325, 325 L, 325 LN, 325B, 325B L, OEMS
6Y0848
BUSHING-MASTER
320B, 322 FM L, 322B L, 325, 325 L, 325 LN, 325B, 325B L, OEMS
320B, 322 FM L, 322B L, 325, 325 L, 325 LN, 325B, 325B L, OEMS
1305674
BUSHING
515
515
1305675
BUSHING
515
515
1343894
BUSHING
525, 525B
525, 525B
1807576
BUSHING
322B LN, 322C, 325C, 325C FM, 325C L
322B LN, 322C, 325C, 325C FM, 325C L
322B LN, 322C, 324D, 325B L, 325C, 325D L, 330C, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336E L, 340D L, 385C L
320 L, 322, 322 LN, 322B, 322B L, 322B LN, 322C, 325, 325 L, 325 LN, 325B, 325B L, 325C, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 385B
1190T, 1290T, 2391, 2491, 320 L, 320B, 320C, 320N, 322, 322 L, 322 LN, 322B, 322B L, 322C, 322C FM, 325, 325 L, 325 LN, 325B L, 325C, 325C L, 330, 330 FM L, 330 L, 330B, 522, 522B, 532, 552, 552 2, TK...
322B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 330, 330B L, M325B
1262069
BUSHING
320B, 320B L, 321B, 322B L, 322B LN, 325B, 325B L
320B, 320B L, 321B, 322B L, 322B LN, 325B, 325B L