1877769 ENGINE AR-COMPLETE Caterpillar parts
C-10
Rating:
Alternative (cross code) number:
CA1877769
187-7769
1877769
CA1877769
187-7769
1877769
TRUCK ENGINE,
Compatible equipment models: 1877769:
For full view, you need register
Information:
GPS Warning Messages
Table 1 lists the GPS status messages.
Table 1
GPS Status Message Problem Solution
Check Machine Radio The system cannot communicate with the data radio on the machine. Check that power is being supplied to the radio. Check the cable to the radio.
Direction Unknown The machine orientation needs to be initialized. Drive the machine in a forward direction.
Invalid GPS Configuration There is a problem with a GPS receiver output configuration. The coordinate system may be missing from the GPS receiver configuration.
There is GPS data but the data is in the wrong format, or the baud rate is incorrect. Load a design. Doing so will send a valid GPS configuration file to the GPS receivers. Alternatively, contact your supervisor.
V.Low Accuracy (GPS) The AccuGrade System is receiving autonomous GPS positions from the receiver. Check the data radio and base station.
Low Accuracy (GPS) The GPS error estimate has exceeded the limit set by the GPS Accuracy Mode. Change the GPS Accuracy Mode.
Check the data radio and the radio cable.
Ask your site manager to adjust the accuracy limits.
Low Accuracy (Move) The machine has not travelled far enough in its current direction to determine machine slope. Drive the machine slowly in a forward direction.
No GPS Receiver Data There has been no GPS data coming from the GPS receiver for at least 1.5 seconds.
This could be caused by:
a problem with a GPS receiver configuration
a problem with the GPS receiver itself
a cabling fault Check the cable, power, and connections. Check the physical condition of the GPS receivers.
Turn off the Display and then turn the Display back on.
If problems continue, contact your supervisor.
Old Position A position is not being generated by the GPS receiver Check the GPS receivers and cables. General Warning Messages
Table 2 lists warning messages that relate to general AccuGrade System operation.
Table 2
General Warning Messages
Message Reason Solution
Avoid Zone Entered The machine has entered an Avoidance Zone. This is an area that has been designated as dangerous for machine operation. Use Plan View in order to guide the machine out of the Avoidance Zone.
Check Machine Dimensions The set of dimensions that has been entered is incorrect or incomplete. Restore a suitable machine settings file.
Ask the site manager to enter the correct measurements.
Loading Data The CD700 Display is loading the current design information or map information. Wait for the action to complete. The message will disappear when the design or map information has finished loading. Machine Messages
Table 3 lists the messages that relate to the AccuGrade System installed on compactors
Table 3
Compactor Status Messages
Message Indicates that ... Solution
Check Drum Slope Sensor No data is being received from the drum slope sensor. Automatic controls will be disabled and no vertical guidance
Table 1 lists the GPS status messages.
Table 1
GPS Status Message Problem Solution
Check Machine Radio The system cannot communicate with the data radio on the machine. Check that power is being supplied to the radio. Check the cable to the radio.
Direction Unknown The machine orientation needs to be initialized. Drive the machine in a forward direction.
Invalid GPS Configuration There is a problem with a GPS receiver output configuration. The coordinate system may be missing from the GPS receiver configuration.
There is GPS data but the data is in the wrong format, or the baud rate is incorrect. Load a design. Doing so will send a valid GPS configuration file to the GPS receivers. Alternatively, contact your supervisor.
V.Low Accuracy (GPS) The AccuGrade System is receiving autonomous GPS positions from the receiver. Check the data radio and base station.
Low Accuracy (GPS) The GPS error estimate has exceeded the limit set by the GPS Accuracy Mode. Change the GPS Accuracy Mode.
Check the data radio and the radio cable.
Ask your site manager to adjust the accuracy limits.
Low Accuracy (Move) The machine has not travelled far enough in its current direction to determine machine slope. Drive the machine slowly in a forward direction.
No GPS Receiver Data There has been no GPS data coming from the GPS receiver for at least 1.5 seconds.
This could be caused by:
a problem with a GPS receiver configuration
a problem with the GPS receiver itself
a cabling fault Check the cable, power, and connections. Check the physical condition of the GPS receivers.
Turn off the Display and then turn the Display back on.
If problems continue, contact your supervisor.
Old Position A position is not being generated by the GPS receiver Check the GPS receivers and cables. General Warning Messages
Table 2 lists warning messages that relate to general AccuGrade System operation.
Table 2
General Warning Messages
Message Reason Solution
Avoid Zone Entered The machine has entered an Avoidance Zone. This is an area that has been designated as dangerous for machine operation. Use Plan View in order to guide the machine out of the Avoidance Zone.
Check Machine Dimensions The set of dimensions that has been entered is incorrect or incomplete. Restore a suitable machine settings file.
Ask the site manager to enter the correct measurements.
Loading Data The CD700 Display is loading the current design information or map information. Wait for the action to complete. The message will disappear when the design or map information has finished loading. Machine Messages
Table 3 lists the messages that relate to the AccuGrade System installed on compactors
Table 3
Compactor Status Messages
Message Indicates that ... Solution
Check Drum Slope Sensor No data is being received from the drum slope sensor. Automatic controls will be disabled and no vertical guidance