2460674 ENGINE AR-CORE Caterpillar parts
C-10
Rating:
Alternative (cross code) number:
CA2460674
246-0674
2460674
CA2460674
246-0674
2460674
INDUSTRIAL ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$139.48
04 Dec 2023
US: lee's autostore
VHNROFE Built Starter 3.2 196 L4 12V 68 69 70 91013706 1108373 2460674
VHNROFE Perfect Fitment:Before Placing The Order, Please Check Your Car Model in The Amazon Fitment Filter System in the top left corner || Number Of Holes: 2 || Number Of Teeth: 9 || Part Type: Starter Motor W/ Solenoid || Part_Number:2460674,1108373
VHNROFE Perfect Fitment:Before Placing The Order, Please Check Your Car Model in The Amazon Fitment Filter System in the top left corner || Number Of Holes: 2 || Number Of Teeth: 9 || Part Type: Starter Motor W/ Solenoid || Part_Number:2460674,1108373
For full view, you need register
Compatible equipment models: 2460674:
Information:
Start By:
Separate the track. Refer to Disassembly and Assembly, "Track - Separate".
Remove the steering motor. Refer to Disassembly and Assembly, "Steering Motor - Remove".
Remove the drive axles. Refer to Disassembly and Assembly, "Axle - Remove and Install".
Drain the oil from the transmission system. Refer to Operation and Maintenance Manual, "Transmission System Oil and Screens - Change/Clean".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01127146
Remove bolts (1) from adapter (2) .
Install Tooling (D) in Holes (X). Remove adapter (2) .
Illustration 2 g01127151
Remove O-ring seal (3) from adapter (2) .
Illustration 3 g01127160
Illustration 4 g01127169
Insert Tooling (A) 940 mm (37.0 inch) in the final drive housing. Use Tooling (A) in order to slide the sliding carrier off the bevel gear shaft.
Rotate Tooling (A) by 180 degrees.
Pull Tooling (A) until the sliding carrier stops.
Rotate Tooling (A) by 180 degrees and remove Tooling (A) .
Illustration 5 g01127173
Illustration 6 g01127177
Adjust Tooling (B) as Tooling (B) is shown in Illustration 5. Remove two bolts (4). Install Tooling (B) and a suitable lifting device. The weight of the final drive, the differential, and the brake is approximately 850 kg (1875 lb).
Remove seven bolts (5). Install Tooling (C) .
Illustration 7 g01127323
Remove remaining bolts (5) and remove bolts (7). Do not remove bolts (6) .
Illustration 8 g01127327
Pull outward on final drive (9), steering differential (10), and brake (11) by approximately 25 mm (1.0 inch). Final drive (9), steering differential (10), and brake (11) should move freely.
Use Tooling (C) in order to rotate final drive (9), steering differential (10), and brake (11) by 45 to 60 degrees counterclockwise.
Remove final drive (9), steering differential (10), and brake (11) .
Remove O-ring seals (8) .
Separate the track. Refer to Disassembly and Assembly, "Track - Separate".
Remove the steering motor. Refer to Disassembly and Assembly, "Steering Motor - Remove".
Remove the drive axles. Refer to Disassembly and Assembly, "Axle - Remove and Install".
Drain the oil from the transmission system. Refer to Operation and Maintenance Manual, "Transmission System Oil and Screens - Change/Clean".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01127146
Remove bolts (1) from adapter (2) .
Install Tooling (D) in Holes (X). Remove adapter (2) .
Illustration 2 g01127151
Remove O-ring seal (3) from adapter (2) .
Illustration 3 g01127160
Illustration 4 g01127169
Insert Tooling (A) 940 mm (37.0 inch) in the final drive housing. Use Tooling (A) in order to slide the sliding carrier off the bevel gear shaft.
Rotate Tooling (A) by 180 degrees.
Pull Tooling (A) until the sliding carrier stops.
Rotate Tooling (A) by 180 degrees and remove Tooling (A) .
Illustration 5 g01127173
Illustration 6 g01127177
Adjust Tooling (B) as Tooling (B) is shown in Illustration 5. Remove two bolts (4). Install Tooling (B) and a suitable lifting device. The weight of the final drive, the differential, and the brake is approximately 850 kg (1875 lb).
Remove seven bolts (5). Install Tooling (C) .
Illustration 7 g01127323
Remove remaining bolts (5) and remove bolts (7). Do not remove bolts (6) .
Illustration 8 g01127327
Pull outward on final drive (9), steering differential (10), and brake (11) by approximately 25 mm (1.0 inch). Final drive (9), steering differential (10), and brake (11) should move freely.
Use Tooling (C) in order to rotate final drive (9), steering differential (10), and brake (11) by 45 to 60 degrees counterclockwise.
Remove final drive (9), steering differential (10), and brake (11) .
Remove O-ring seals (8) .