2H9524 GROMMET Caterpillar parts
12G, 14G, 245, 245B, 245D, 304, 5130, 5130B, 5230, 5230B, 621, 621B, 623, 627, 627B, 631C, 633C, 637, 637D, 641, 641B, 650B, 651, 657, 657B, 666, 666B, 69D, 768C, 769C, 769D, 771C, 771D, 772B, 777, 78...
Rating:
Alternative (cross code) number:
CA2H9524
2H-9524
2H9524
CA2H9524
2H-9524
2H9524
Weight: 0.03 pounds 0 kg.
Information:
GROOVE WIDTH
19.05
mm
ID/WIDTH
22.22
mm
LARGER OD
41.28
mm
RADIUSED CHAMFER
Y
SMALLER OD
31.75
mm
SPLIT
Y
THICKNESS
28.58
mm
COMPACT WHEEL LOADER, WHEEL TRACTOR,
Compatible equipment models: 2H9524:
COMPACT WHEEL LOADER
904B
INDUSTRIAL ENGINE
D398
MINI HYD EXCAVATOR
304
PNEUMATIC COMPACTOR
CW-34
TRUCK
69D
769C
769D
777
785
785B
785C
785D
789
789B
789C
789D
793
793B
793C
793D
793F
793F AC
793F CMD
793F OEM
795F AC
797F
Information:
Use only clean water to flush the cooling system when Extended Life Coolant (ELC) is drained and replaced.Drain the Cooling System
Stop the engine and allow the engine to cool. Close the water inlet for the separate circuit aftercooler. Ensure that the engine will not start when the cooling system is drained.
Loosen the radiator filler cap slowly in order to relieve any pressure. Remove the radiator filler cap.
Illustration 1 g03875342
The cooling system drain is located behind the rear doors.
(1) Coolant drain
Illustration 2 g03875237
Location of the cooling system drain plugs
(2) Engine oil cooler
(3) Jacket water pump
(4) Cylinder block
(5) SCAC pump and thermostat housing Note: If the engine has a jacket water heater, drain the coolant from the heater.
Open the coolant drain. Remove the cooling system drain plugs. Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Cat dealer or consult Caterpillar Service Technology Group:Outside U.S.A. (309) 675-6277
Inside U.S.A. 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
CSTG COSA Geneva, Switzerland 41-22-849 40 56
Clean the Cooling System
After the cooling system has been drained, flush the cooling system with clean water in order to remove any debris.
Close the coolant system drain. Clean the cooling system drain plugs and install the cooling system drain plugs.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Open the water inlet for the separate circuit aftercooler (if equipped). Fill the cooling system with clean water. Install the radiator filler cap. Operate the engine until the temperature reaches 66 °C (150 °F).
Stop the engine and allow the engine to cool. Close the water inlet for the separate circuit aftercooler (if equipped). Ensure that the engine will not start when the cooling system is drained. Loosen the radiator filler cap slowly in order to relieve any pressure. Remove the radiator filler cap.
Open the cooling system drain. Remove the cooling system drain plugs. Allow the coolant to drain. Flush the cooling system with clean water. Close the cooling system drain. Install the cooling system drain plugs.
Repeat Steps 3, 4, and 5. Fill the Cooling System
Note: For information about the proper coolant to use, see this Operation and Maintenance Manual, "Coolant Recommendations" (Maintenance Section). For the capacity of the cooling system, see this Operation and Maintenance Manual, "Refill Capacities" (Maintenance Section).
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with Extended Life Coolant (ELC). After filling the cooling system, do not install the radiator filler cap.
Open the water inlet for the separate circuit aftercooler (if equipped). Start the engine. Operate the engine in order to purge the air from the cavities of the engine block. Allow the ELC to warm and allow the coolant level to stabilize. Stop the engine.
Check the coolant
Stop the engine and allow the engine to cool. Close the water inlet for the separate circuit aftercooler. Ensure that the engine will not start when the cooling system is drained.
Loosen the radiator filler cap slowly in order to relieve any pressure. Remove the radiator filler cap.
Illustration 1 g03875342
The cooling system drain is located behind the rear doors.
(1) Coolant drain
Illustration 2 g03875237
Location of the cooling system drain plugs
(2) Engine oil cooler
(3) Jacket water pump
(4) Cylinder block
(5) SCAC pump and thermostat housing Note: If the engine has a jacket water heater, drain the coolant from the heater.
Open the coolant drain. Remove the cooling system drain plugs. Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Cat dealer or consult Caterpillar Service Technology Group:Outside U.S.A. (309) 675-6277
Inside U.S.A. 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
CSTG COSA Geneva, Switzerland 41-22-849 40 56
Clean the Cooling System
After the cooling system has been drained, flush the cooling system with clean water in order to remove any debris.
Close the coolant system drain. Clean the cooling system drain plugs and install the cooling system drain plugs.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Open the water inlet for the separate circuit aftercooler (if equipped). Fill the cooling system with clean water. Install the radiator filler cap. Operate the engine until the temperature reaches 66 °C (150 °F).
Stop the engine and allow the engine to cool. Close the water inlet for the separate circuit aftercooler (if equipped). Ensure that the engine will not start when the cooling system is drained. Loosen the radiator filler cap slowly in order to relieve any pressure. Remove the radiator filler cap.
Open the cooling system drain. Remove the cooling system drain plugs. Allow the coolant to drain. Flush the cooling system with clean water. Close the cooling system drain. Install the cooling system drain plugs.
Repeat Steps 3, 4, and 5. Fill the Cooling System
Note: For information about the proper coolant to use, see this Operation and Maintenance Manual, "Coolant Recommendations" (Maintenance Section). For the capacity of the cooling system, see this Operation and Maintenance Manual, "Refill Capacities" (Maintenance Section).
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with Extended Life Coolant (ELC). After filling the cooling system, do not install the radiator filler cap.
Open the water inlet for the separate circuit aftercooler (if equipped). Start the engine. Operate the engine in order to purge the air from the cavities of the engine block. Allow the ELC to warm and allow the coolant level to stabilize. Stop the engine.
Check the coolant
Cat SIS web machinery list:
Parts grommet Caterpillar catalog:
3G8047
GROMMET
16M, 2470C, 24H, 24M, 2570C, 2670C, 2864C, 307B, 307C, 308D, 308E, 308E2 CR, 312C, 316E L, 318E L, 320B FM LL, 320C, 322 FM L, 330D L, 336D L, 336E HVG, 345C L, 349E L HVG, 385B, 390D, 390D L, 416E, 4...
16M, 2470C, 24H, 24M, 2570C, 2670C, 2864C, 307B, 307C, 308D, 308E, 308E2 CR, 312C, 316E L, 318E L, 320B FM LL, 320C, 322 FM L, 330D L, 336D L, 336E HVG, 345C L, 349E L HVG, 385B, 390D, 390D L, 416E, 4...
6V1869
GROMMET
24H, 330D MH, 345C, 345C MH, 3508B, 3512B, 3516B, 365C, 365C L, 365C L MH, 374D L, 375, 416E, 420E, 430E, 432E, 434E, 5080, 5110B, 5130, 5130B, 5230, 5230B, 525C, 535C, 545C, 589, 735, 735B, 740, 740B...
24H, 330D MH, 345C, 345C MH, 3508B, 3512B, 3516B, 365C, 365C L, 365C L MH, 374D L, 375, 416E, 420E, 430E, 432E, 434E, 5080, 5110B, 5130, 5130B, 5230, 5230B, 525C, 535C, 545C, 589, 735, 735B, 740, 740B...
5B0131
GROMMET
120B, 12E, 140B, 16, 1673, 1673C, 3412, 621, 627, 641, 651, 657, 657B, 666, 814, 816, 824, 824B, 824C, 825B, 826B, 834, 936, 966C, 977H, 980, 980B, 980C, 980F, 980F II, 988, 992, D342, D346, D348, D34...
120B, 12E, 140B, 16, 1673, 1673C, 3412, 621, 627, 641, 651, 657, 657B, 666, 814, 816, 824, 824B, 824C, 825B, 826B, 834, 936, 966C, 977H, 980, 980B, 980C, 980F, 980F II, 988, 992, D342, D346, D348, D34...
3D2023
GROMMET
12E, 14E, 16, 3406, 3408, 824, 824B, 824S, 825B, 826B, 834, 920, 930, 950, 955H, 966C, 980, 988, 992, D333A, D379, D379A, D379B, D398, D398A, D398B, D399, D4D, D8H, D8K, D9G
12E, 14E, 16, 3406, 3408, 824, 824B, 824S, 825B, 826B, 834, 920, 930, 950, 955H, 966C, 980, 988, 992, D333A, D379, D379A, D379B, D398, D398A, D398B, D399, D4D, D8H, D8K, D9G
1003237
GROMMET
2864C, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390D, 39...
2864C, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390D, 39...
5B0494
GROMMET CLIP TO TUBE
120, 120B, 12E, 140, 140B, 14E, 1673, D326F, D337F, D342, D342C, D343, D353C, D379, D398, D9E, G342C, G379
120, 120B, 12E, 140, 140B, 14E, 1673, D326F, D337F, D342, D342C, D343, D353C, D379, D398, D9E, G342C, G379
9M5617
GROMMET
120G, 12G, 130G, 140G, 14G, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304C CR, 304D CR, 304E, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 3406B, 3406C, 3406E, 561B, 561C, 571G, 572G, 589, 824C, 825C, 826C...
120G, 12G, 130G, 140G, 14G, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304C CR, 304D CR, 304E, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 3406B, 3406C, 3406E, 561B, 561C, 571G, 572G, 589, 824C, 825C, 826C...
7K6416
GROMMET
130G, 235, 245, 508, 611, 613C II, 615C, 69D, 769D, 771D, 773D, 773E, 775D, 775E, 776D, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 793B, 793C, 793D, 797B, 814, 824G, 825G, 826G, 834B, 836, 906H, ...
130G, 235, 245, 508, 611, 613C II, 615C, 69D, 769D, 771D, 773D, 773E, 775D, 775E, 776D, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 793B, 793C, 793D, 797B, 814, 824G, 825G, 826G, 834B, 836, 906H, ...
6V0974
GROMMET
120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 225, 24H, 24M, 320D, 320D FM RR, 320D LRR, 320D RR, 322 FM L, 323D L, 323D LN, 323D SA, 3...
120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 225, 24H, 24M, 320D, 320D FM RR, 320D LRR, 320D RR, 322 FM L, 323D L, 323D LN, 323D SA, 3...
6T9807
GROMMET
572R, 572R II, 578, 583R, 583T, 587R, 587T, D11T, D6G2 LGP, D6G2 XL, D6H, D6H II, D6H XL, D6H XR, D6R, D7G, D7G2, D7H, D7R, D7R II, D7R XR, D8N, D8R, PL83, PL87, R2900
572R, 572R II, 578, 583R, 583T, 587R, 587T, D11T, D6G2 LGP, D6G2 XL, D6H, D6H II, D6H XL, D6H XR, D6R, D7G, D7G2, D7H, D7R, D7R II, D7R XR, D8N, D8R, PL83, PL87, R2900
6T5612
GROMMET
621E, 621F, 621G, 621H, 621K, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 657G, 69D, 769C, 769D, 770, 771C, 771D, 772, ...
621E, 621F, 621G, 621H, 621K, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 657G, 69D, 769C, 769D, 770, 771C, 771D, 772, ...
2D2508
GROMMET
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
8F2396
GROMMET
120, 12E, 140, 16, 1673, 1673B, 225, 3304, 3306, 583H, 630A, 641, 651, 657, 768B, 769, 772, 793, 793B, 793C, 793D, 920, 966C, 977L, 992, D330A, D342, D342C, D343, D353C, D398, D8H, D9E, D9G, G3304, G3...
120, 12E, 140, 16, 1673, 1673B, 225, 3304, 3306, 583H, 630A, 641, 651, 657, 768B, 769, 772, 793, 793B, 793C, 793D, 920, 966C, 977L, 992, D330A, D342, D342C, D343, D353C, D398, D8H, D9E, D9G, G3304, G3...
4N9521
GROMMET
3406
3406
0486029
GROMMET
D353C
D353C
7S5843
GROMMET
641B, 650B, 772, 773, 777, D10, D346, D348, D349, D379, D379B, D398, D398B, D399
641B, 650B, 772, 773, 777, D10, D346, D348, D349, D379, D379B, D398, D398B, D399
5B0648
GROMMET
12E, 1673, D315, D337, D337F, D342, D342C, D348, D349, D353C, D364, D399, D5B, G342C, G379, G398
12E, 1673, D315, D337, D337F, D342, D342C, D348, D349, D353C, D364, D399, D5B, G342C, G379, G398
3K8785
GROMMET
120, 120G, 12F, 12G, 130G, 140, 140G, 14E, 16, 16G, 301.6C, 302.5C, 307, 613B, 621E, 623E, 627E, 631E, 637E, 651E, 657E, 814F, 814F II, 815F, 815F II, 816F, 816F II, 906H, 907H, 908H, 910K, 914K, 918F...
120, 120G, 12F, 12G, 130G, 140, 140G, 14E, 16, 16G, 301.6C, 302.5C, 307, 613B, 621E, 623E, 627E, 631E, 637E, 651E, 657E, 814F, 814F II, 815F, 815F II, 816F, 816F II, 906H, 907H, 908H, 910K, 914K, 918F...
2H5002
GROMMET
D337
D337
6F9133
GROMMET
D364, D375D, D397D
D364, D375D, D397D
5B1344
GROMMET
16, 814, 815, 920, 930, 950, 966C, 980, 980B, D315, D364, D375D, D397D, D9E
16, 814, 815, 920, 930, 950, 966C, 980, 980B, D315, D364, D375D, D397D, D9E
6F9090
GROMMET
D364, D375D, D397D
D364, D375D, D397D
6F9087
GROMMET
D364
D364
1F0082
GROMMET
12E, 16, 657, 955C, 955H, 977H, D315, D320A, D326F, D330A, D333A, D337, D337F, D342, D342C, D353C, D364, D379, D379A, D397D, D8H
12E, 16, 657, 955C, 955H, 977H, D315, D320A, D326F, D330A, D333A, D337, D337F, D342, D342C, D353C, D364, D379, D379A, D397D, D8H