1222739 HOSE AS Caterpillar parts
312B L, 315B L, 317B LN, 318B, 320B, 322 FM L, 322 LN, 322B L, 322B LN, 325, 325 FM L, 325B L, 325C FM, 330, 330 L, 330B L, 330C FM, 345B II, 345B L, 365B, 365B II, 385B
Rating:
Alternative (cross code) number:
CA1222739
122-2739
1222739
CA1222739
122-2739
1222739
Weight: 0.40 pounds 0 kg.
EXCAVATOR,
Compatible equipment models: 1222739:
Number on catalog scheme:
35
For full view, you need register
Information:
Removal Procedure
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Drain the engine oil into a suitable container for storage or disposal. Refer to the Operation and Maintenance Manual.
Illustration 1 g01519876Note: Do not pry or gouge the sealing surface of the engine oil pan. Use a rubber mallet to tap lightly on the engine oil pan, if it is necessary.
Remove bolts (2). Remove engine oil pan (1) and the gasket. Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Do not put liquid gasket material on the oil pan gasket or on the gasket surface of the engine oil pan.
Illustration 2 g01519876
Illustration 3 g00610574
Place a new gasket and engine oil pan (1) on the cylinder block.
Install bolts (2) for engine oil pan (1). Tighten Bolts (X). Tighten the bolts to a torque of 31 3 N m (23 2 lb ft).
Start at Position (Z) and tighten the remaining bolts in a counterclockwise direction. Tighten the remaining bolts to a torque of 31 3 N m (23 2 lb ft).
Start at Position (Z) and tighten the bolts again in a counterclockwise direction. Tighten the bolts to a torque of 31 3 N m (23 2 lb ft).
Fill the engine with oil to the correct level. Refer to the Operation and Maintenance Manual for the correct filling procedure.
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Drain the engine oil into a suitable container for storage or disposal. Refer to the Operation and Maintenance Manual.
Illustration 1 g01519876Note: Do not pry or gouge the sealing surface of the engine oil pan. Use a rubber mallet to tap lightly on the engine oil pan, if it is necessary.
Remove bolts (2). Remove engine oil pan (1) and the gasket. Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Do not put liquid gasket material on the oil pan gasket or on the gasket surface of the engine oil pan.
Illustration 2 g01519876
Illustration 3 g00610574
Place a new gasket and engine oil pan (1) on the cylinder block.
Install bolts (2) for engine oil pan (1). Tighten Bolts (X). Tighten the bolts to a torque of 31 3 N m (23 2 lb ft).
Start at Position (Z) and tighten the remaining bolts in a counterclockwise direction. Tighten the remaining bolts to a torque of 31 3 N m (23 2 lb ft).
Start at Position (Z) and tighten the bolts again in a counterclockwise direction. Tighten the bolts to a torque of 31 3 N m (23 2 lb ft).
Fill the engine with oil to the correct level. Refer to the Operation and Maintenance Manual for the correct filling procedure.
Caterpillar parts catalog:
Parts hose Caterpillar catalog:
330B, 330B L
330B, 330B L
330 FM L, 330 L, 330B, 330B L, W330B
330B, 330B L, 365C, 365C L, W330B
330B, 330B L, W330B
325B L, 330B, 330B L, W330B
330B, 330B L
330B, 330B L
328D LCR, 365B, 365B II, 365B L, 365C, 365C L
330C, 365B, 365B II, 365B L, 365C L MH
365B, 365B II, 365B L, 365C, 365C L
330 L
1460675
HOSE AS
312B L, 317B LN, 318B, 322B L, 322B LN
312B L, 317B LN, 318B, 322B L, 322B LN
1059488
HOSE AS
312B L, 375, 375 L, 5080
312B L, 375, 375 L, 5080
1272396
HOSE AS
307B, 312B L, 315B L, 317B LN, 318B, 320B, 320B FM LL, 322B L, 322B LN, 325B L, 330B L, 345B, 345B II, 345B II MH, 345B L, 385B, 5110B, M325B, W330B, W345B II
307B, 312B L, 315B L, 317B LN, 318B, 320B, 320B FM LL, 322B L, 322B LN, 325B L, 330B L, 345B, 345B II, 345B II MH, 345B L, 385B, 5110B, M325B, W330B, W345B II
1213374
HOSE
312B L, 315B L, 317B LN, 318B, 320B, 322 FM L, 322B L, 322B LN, 325B L, 330, 330B L, 345B II, 345B L, 350, 365B, 365B II, 375, 375 L, 385B, 5080, 5090B, 5110B
312B L, 315B L, 317B LN, 318B, 320B, 322 FM L, 322B L, 322B LN, 325B L, 330, 330B L, 345B II, 345B L, 350, 365B, 365B II, 375, 375 L, 385B, 5080, 5090B, 5110B
312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 325C, 325C FM, 325D, 325D FM, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN
1218659
HOSE AS
311B, 311C, 311D LRR, 311F LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
311B, 311C, 311D LRR, 311F LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
1478414
HOSE AS
M318, M320
M318, M320
2158239
HOSE AS
5110B, M318
5110B, M318
1245274
HOSE AS
M313C, M313D, M315C, M315D, M316C, M316D, M318, M318C, M318C MH, M320
M313C, M313D, M315C, M315D, M316C, M316D, M318, M318C, M318C MH, M320
312B L, 315B L, 317B LN, 318B
1135946
HOSE AS
312B L, 814F, 815F, 816F, 938F, 966F, 966F II, 970F
312B L, 814F, 815F, 816F, 938F, 966F, 966F II, 970F
1478437
HOSE AS
312B L
312B L