BL26000 Lafayette 3616 Engine Caterpillar parts
3616
Rating:
Alternative (cross code) number:
CABL26000
BL2-6000
BL26000
CABL26000
BL2-6000
BL26000
MARINE ENGINE,
Compatible equipment models: BL26000:
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4390 E12 Torx Socket 1
B FT-2806 Alignment Tool 1 Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02450219
Illustration 2 g02450222
Ensure that crankshaft flange (1) is clean, dry, and free from damage.
Ensure that the face of the cylinder block and the bridge piece are clean and dry.
A new crankshaft rear seal is supplied with a plastic sleeve (3). Ensure that the plastic sleeve is squarely installed within crankshaft rear seal (2). Note: The plastic sleeve is included in order to protect the lip of the seal as the seal is pushed over the crankshaft flange.Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The crankshaft rear seal must be installed dry.
Align plastic sleeve (3) with crankshaft flange (1). Ensure that the plastic sleeve is engaged onto the crankshaft flange. Push new crankshaft rear seal (2) squarely onto the crankshaft flange. During this process, the plastic sleeve will be forced out of the crankshaft rear seal. Discard the plastic sleeve.
Align the two molded locators on crankshaft rear seal (2) with the holes in the cylinder block. Ensure that the crankshaft rear seal is seated against the cylinder block.
Illustration 3 g02451996
Install torx screws (4) finger tight. Tightening sequence for the crankshaft rear sealNote: Do not install torx screws to Positions (X) at this stage.
Install Tooling (B) to crankshaft rear seal (2) and to crankshaft flange (1).
Use Tooling (A) in order to tighten torx screws (4) to a torque of 22 N m (16 lb ft). Tighten torx screws (4) in the sequence that is shown in Illustration 3.
Remove Tooling (B).
Install remaining torx screws (4) to Positions (X). Use Tooling (A) in order to tighten the torx screws to a torque of 22 N m (16 lb ft). Refer to Illustration 3. End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 227-4390 E12 Torx Socket 1
B FT-2806 Alignment Tool 1 Note: The crankshaft rear seal and the housing are manufactured as a one-piece assembly.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02450219
Illustration 2 g02450222
Ensure that crankshaft flange (1) is clean, dry, and free from damage.
Ensure that the face of the cylinder block and the bridge piece are clean and dry.
A new crankshaft rear seal is supplied with a plastic sleeve (3). Ensure that the plastic sleeve is squarely installed within crankshaft rear seal (2). Note: The plastic sleeve is included in order to protect the lip of the seal as the seal is pushed over the crankshaft flange.Note: Do not lubricate the crankshaft rear seal or the crankshaft flange. The crankshaft rear seal must be installed dry.
Align plastic sleeve (3) with crankshaft flange (1). Ensure that the plastic sleeve is engaged onto the crankshaft flange. Push new crankshaft rear seal (2) squarely onto the crankshaft flange. During this process, the plastic sleeve will be forced out of the crankshaft rear seal. Discard the plastic sleeve.
Align the two molded locators on crankshaft rear seal (2) with the holes in the cylinder block. Ensure that the crankshaft rear seal is seated against the cylinder block.
Illustration 3 g02451996
Install torx screws (4) finger tight. Tightening sequence for the crankshaft rear sealNote: Do not install torx screws to Positions (X) at this stage.
Install Tooling (B) to crankshaft rear seal (2) and to crankshaft flange (1).
Use Tooling (A) in order to tighten torx screws (4) to a torque of 22 N m (16 lb ft). Tighten torx screws (4) in the sequence that is shown in Illustration 3.
Remove Tooling (B).
Install remaining torx screws (4) to Positions (X). Use Tooling (A) in order to tighten the torx screws to a torque of 22 N m (16 lb ft). Refer to Illustration 3. End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct procedure.