WVB8100 Lafayette 3612 Engine Caterpillar parts
G3612
Rating:
Alternative (cross code) number:
CAWVB8100
WVB-8100
WVB8100
CAWVB8100
WVB-8100
WVB8100
GAS ENGINE,
Compatible equipment models: WVB8100:
For full view, you need register
Information:
Introduction
This Special Instruction is organized into modules. Caterpillar suggests installing one module at a time.Reference: Training Bulletin, GEGT0001, "Cat Pin Grabber Coupler". This guide contains an interactive 3D model in .pdf format that is available for free download at https://cmic.cat.com. Download the file. Open with Adobe Acrobat. Enable Content. Click on the image to activate. This guide is to be used as an installation and training aid. Refer to the Special Instructions for the latest parts information.Note: Drain the hydraulic fluid from the hydraulic tank before opening the hydraulic system. Remember to fill the hydraulic tank with hydraulic fluid once the installation is complete.Required Parts
Table 1
456-4103 Coupler Control Ar - 00
Part Number Description Media Number
238-2485 Toggle Switch Gp GEHS0787
456-4104 Front Lines Gp GEHS0806
342-3026 Quick Coupler Wiring Gp GEHS0789
343-8342 Hydraulic Lines Kit REHS3854
448-4756 Film Gp - Serial Number Identification
Caterpillar Work Tools hydraulic kits are identified with serial numbers. The serial number is printed on a film group (1). This film group should be placed on the right-hand window inside the cab.
Illustration 1 g01742203
448-4756 Film Gp
Illustration 2 g01743196Tuning Section
Note: The latest software must be flashed to the Machine and Monitor ECM prior to the Test and Adjust section.
Monitor setting: Go to "Service" page.
Next enter "Configurations" page, then "Machine Attachments".
Set "Quick Coupler" to: "Installed w/o Coupler Accelerator", then scroll down, find the item "QC constant Engagement Pressure System".
Finally, set it to "Installed".Reference: Systems Operation, KENR6595, "Testing and Adjusting Section", "Process for Setting Up the Work Tool"
This Special Instruction is organized into modules. Caterpillar suggests installing one module at a time.Reference: Training Bulletin, GEGT0001, "Cat Pin Grabber Coupler". This guide contains an interactive 3D model in .pdf format that is available for free download at https://cmic.cat.com. Download the file. Open with Adobe Acrobat. Enable Content. Click on the image to activate. This guide is to be used as an installation and training aid. Refer to the Special Instructions for the latest parts information.Note: Drain the hydraulic fluid from the hydraulic tank before opening the hydraulic system. Remember to fill the hydraulic tank with hydraulic fluid once the installation is complete.Required Parts
Table 1
456-4103 Coupler Control Ar - 00
Part Number Description Media Number
238-2485 Toggle Switch Gp GEHS0787
456-4104 Front Lines Gp GEHS0806
342-3026 Quick Coupler Wiring Gp GEHS0789
343-8342 Hydraulic Lines Kit REHS3854
448-4756 Film Gp - Serial Number Identification
Caterpillar Work Tools hydraulic kits are identified with serial numbers. The serial number is printed on a film group (1). This film group should be placed on the right-hand window inside the cab.
Illustration 1 g01742203
448-4756 Film Gp
Illustration 2 g01743196Tuning Section
Note: The latest software must be flashed to the Machine and Monitor ECM prior to the Test and Adjust section.
Monitor setting: Go to "Service" page.
Next enter "Configurations" page, then "Machine Attachments".
Set "Quick Coupler" to: "Installed w/o Coupler Accelerator", then scroll down, find the item "QC constant Engagement Pressure System".
Finally, set it to "Installed".Reference: Systems Operation, KENR6595, "Testing and Adjusting Section", "Process for Setting Up the Work Tool"