4E3645 NUT-ADJUSTMENT Caterpillar parts
2470C, 2570C, 2670C, 2864C, 525B, 525C, 533, 535B, 535C, 543, 545, 545C, 553C, 563C, 573C, 586C, 814F, 814F II, 815F, 815F II, 816F, 816F II, 966F, 966F II, 970F, HA770, HA771, HA870, HA871, R1600, R1...
Rating:
Alternative (cross code) number:
CA4E3645
4E-3645
4E3645
CA4E3645
4E-3645
4E3645
Weight: 3 pounds 1 kg.
INDUSTRIAL TRACTOR, WHEEL SKIDDER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$87.87
12 May 2022
Amazon.com
CTP 4E3645 Hex Head Nut for Heavy Equipment
CTP Hex Head Type of Nut || Sold in each || Easy in-and-out fit
CTP Hex Head Type of Nut || Sold in each || Easy in-and-out fit
$83.65
10 Feb 2019
401 Hundredths Pounds
CTP: CTP
4E3645 Nut Fits Caterpillar
Warranty
Warranty
Number on catalog scheme:
17
For full view, you need register
Compatible equipment models: 4E3645:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 0V-0375 Bolt 1
5P-8245 Hard Washer 1 Start By:
Install the lifting brackets on the engine. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00921920Note: Mark the positions of supports (4) and shims (5). The engine supports on the right side are attached to plates (6) on the generator base by dowels (1). Dowels (1) must be removed before the mounting supports can be removed.
Use Tooling (A) to remove dowels (1).
Attach a suitable lifting device to the lifting brackets. The weight of the six cylinder engine is approximately 15 650 kg (34,500 lb). The weight of the eight cylinder engine is approximately 20 412 kg (45,000 lb). Note: The weight is ONLY for the engine.
Loosen bolt (2).
Remove bolts (3) that hold the engine supports to the base.
Lift the engine enough in order to place a nylon strap around the support. The weight of each support is approximately 64 kg (141 lb).
Illustration 2 g00921919
Remove bolts (8) that hold the support (4) to the cylinder block.
Tap support (4) with a large plastic hammer in order to disengage dowels (7) from the cylinder block.
Remove support (4) from the side of the cylinder block.
If necessary, remove dowels (7) from engine support (4). Installation Procedure
Illustration 3 g00921919
If dowels (7) were removed from support (4), install dowels (7). Dowels (7) should extend 20.0 1.0 mm (0.79 0.04 inch) above the surface of support (4).
Put the support in the correct position on the cylinder block. Install the bolts (8). Tighten the bolts to a torque of 1125 100 N m (830 75 lb ft).
Illustration 4 g00921920
Install shims (5) in the regular location.
Lower the engine onto plates (6). Install bolts (3).
Install dowels (1) through engine support (4) and into plate (6) on the right side of the engine.
Check the alignment between the engine and the driven equipment. End By:
Remove the lifting brackets from the engine. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 0V-0375 Bolt 1
5P-8245 Hard Washer 1 Start By:
Install the lifting brackets on the engine. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00921920Note: Mark the positions of supports (4) and shims (5). The engine supports on the right side are attached to plates (6) on the generator base by dowels (1). Dowels (1) must be removed before the mounting supports can be removed.
Use Tooling (A) to remove dowels (1).
Attach a suitable lifting device to the lifting brackets. The weight of the six cylinder engine is approximately 15 650 kg (34,500 lb). The weight of the eight cylinder engine is approximately 20 412 kg (45,000 lb). Note: The weight is ONLY for the engine.
Loosen bolt (2).
Remove bolts (3) that hold the engine supports to the base.
Lift the engine enough in order to place a nylon strap around the support. The weight of each support is approximately 64 kg (141 lb).
Illustration 2 g00921919
Remove bolts (8) that hold the support (4) to the cylinder block.
Tap support (4) with a large plastic hammer in order to disengage dowels (7) from the cylinder block.
Remove support (4) from the side of the cylinder block.
If necessary, remove dowels (7) from engine support (4). Installation Procedure
Illustration 3 g00921919
If dowels (7) were removed from support (4), install dowels (7). Dowels (7) should extend 20.0 1.0 mm (0.79 0.04 inch) above the surface of support (4).
Put the support in the correct position on the cylinder block. Install the bolts (8). Tighten the bolts to a torque of 1125 100 N m (830 75 lb ft).
Illustration 4 g00921920
Install shims (5) in the regular location.
Lower the engine onto plates (6). Install bolts (3).
Install dowels (1) through engine support (4) and into plate (6) on the right side of the engine.
Check the alignment between the engine and the driven equipment. End By:
Remove the lifting brackets from the engine. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".
Cat SIS web machinery list:
Parts nut Caterpillar catalog:
44, 46, 525B, 535B, 6A, 7A, 8 SR, 8A, 955K, 955L, 977L, D6D, D6E, D6E SR, D6F SR, D6G, D6G SR, D6G2 LGP, D6G2 XL
2470C, 2570C, 2670C, 2864C, 515, 518C, 525, 525B, 525C, 533, 535B, 535C, 543, 545, 545C, 553C, 563C, 573C, 586C, 936F, 938F, 938G, 938G II, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G I...
515, 518C, 525, 525B, 525C, 533, 936F, 938F, 938G, 938G II, HA770, HA771, IT38F, IT38G, IT38G II, TK370, TK371
16, 525B, 525C, 535B, 535C, 545, 545C, 611, 613G, 615, 615C, 772, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G ...
518, 518C, 528, 528B, 530B, 611, 613B, 613C, 613C II, 615, 615C, 621B, 621E, 621F, 623E, 623F, 627E, 627F, 631C, 631E, 633E II, 637E, 639D, 651E, 657E, 769D, 771D, 773D, 773E, 775D, 775E, 776D, 777D, ...
528, 528B, 530B, 613, 613B, 613C, 613C II, 613G, 814B, 815B, 816B, 950B, 950B/950E, 966D, 966F, 966G, D25C, D25D, D300E, D30C, D350C, D350E, D35C, D35HP, D400, D400E, D40D
528, 528B, 530B, 613C, 613C II, 621, 621B, 621E, 621F, 621G, 623E, 623F, 623G, 627E, 627F, 627G, 814, 814B, 815B, 824C, 826C, 926, 936, 936F, 950, 950B, 950F, 950F II, 966C, 966D, 966F, 966F II, 966R,...
814F, 814F II, 815F, 815F II, 816F, 816F II, 928F, 928G, 928H, 928HZ, 930G, 966F, 966F II, 970F, IT18F, IT28F, IT28G, R1600, R1600G, R1600H
2470C, 2570C, 2670C, 2864C, 525B, 525C, 525D, 533, 535B, 535C, 535D, 543, 545, 545C, 545D, 553C, 555D, 563C, 573C, 586C, 938H, 950 GC, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 96...
545, 545C, 545D, 555D, 814F, 814F II, 815F, 815F II, 816F, 816F II, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G, 972G II, 972H, 972K, 972M, 972M XE, IT38G II
545, 545C, 545D, 555D, 814F, 814F II, 815F, 815F II, 816F, 816F II, 966F, 966F II, 970F, R1600, R1600G, R1600H
814B, 815B, 816B, 966D, 966F, 966G, D25D, D350E, D400E, D40D
545, 545C, 545D, 555D, 814F, 814F II, 815F, 815F II, 816F, 816F II, 966F, 966F II, 970F, R1600, R1600G, R1600H
8R2583
NUT AS
994
994
1017371
NUT
994
994
1019620
NUT
994
994
793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 993K, 994, 994D, 994F, 994H
2731867
NUT AS
993K, 994, 994D, 994F, 994H
993K, 994, 994D, 994F, 994H
8T4589
NUT
854K, 992K, 993K
854K, 992K, 993K
2542162
NUT
834G, 836G, 988G, 988H, 992G
834G, 836G, 988G, 988H, 992G
950G, 950G II, 962G, 962G II
3E1812
NUT-RETAINER
834G, 836G, 854G, 988G, 992G, 994D
834G, 836G, 854G, 988G, 992G, 994D
12M 2, 140M, 14M, 160M, 16M, 24M, 950H, 950K, 962H, 962K, 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE, 980G, 980G II, 980H, 980K, 980K HLG, SNOW WING
1491421
NUT-CASTLE
950F II, 960F, 966F, 966F II, 970F
950F II, 960F, 966F, 966F II, 970F