0000127 PIN Caterpillar parts
Rating:
Alternative (cross code) number:
CA0000127
000-0127
0000127
CA0000127
000-0127
0000127
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$6.50
07 Mar 2024
US: StickyThings
Daddy's Lil' Monster - Superhero Films - Vinyl Vehicle Sticker
Sticky Things These are the same sticker designs that we have sold at countless comic con events throughout the western US. || Our vinyl vehicle stickers are made from the best high-performance materials available. Unlike many suppliers, our products are rated for 7-10 years in any weather, either heat or cold, dry or damp. They will not shrink, peel, crack, fade or discolor. || These are the same materials we use for professional installation of vehicle graphics on work trucks and trailers, big-rigs, police and fire vehicles, food trucks, etc. || Your sticker will come with complete instructions for application, with a reference to a guide video that we have posted online. PLEASE BE ADVISED that we accept returns or refunds ONLY for obvious defects in workmanship or materials. They failure of the buyer to properly apply this sticker is not the responsibility of the seller. || The actual sizes of the designs vary, but they are approximately 4.25x6 inches.
Sticky Things These are the same sticker designs that we have sold at countless comic con events throughout the western US. || Our vinyl vehicle stickers are made from the best high-performance materials available. Unlike many suppliers, our products are rated for 7-10 years in any weather, either heat or cold, dry or damp. They will not shrink, peel, crack, fade or discolor. || These are the same materials we use for professional installation of vehicle graphics on work trucks and trailers, big-rigs, police and fire vehicles, food trucks, etc. || Your sticker will come with complete instructions for application, with a reference to a guide video that we have posted online. PLEASE BE ADVISED that we accept returns or refunds ONLY for obvious defects in workmanship or materials. They failure of the buyer to properly apply this sticker is not the responsibility of the seller. || The actual sizes of the designs vary, but they are approximately 4.25x6 inches.
For full view, you need register
Information:
Introduction
This instruction gives the procedure for installing the double lip wiper seal in the head of hydraulic cylinders.Installation of the Seal
Illustration 1 g00997424
Use sandpaper or emery cloth to scuff the surfaces of the counterbore in the cylinder head and the outside diameter (1A) of the wiper seal's metal shell.
Clean the counterbore in head (2) and the outside diameter (1A) of the wiper seal's metal shell with 8T-9011 Component Cleaner or 6V-1541 Quick Cure Primer . Clean the counterbore and the metal shell until neither of the components discolor a clean white towel.Note: The metal shell of the wiper seal is coated with a corrosion inhibitor. This may prevent proper bonding of the wiper seal to the cylinder head if the inhibitor is not removed. After cleaning, do not touch the counterbore or the metal shell because the oil from your fingers may prevent a good bond. Handle the seal by the lip only.
Apply 6V-1541 Quick Cure Primer on the counterbore and the metal shell. Allow the primer to dry. The primer will dry in approximately 30 seconds.
Apply 7M-7456 Bearing Mount Compound evenly but do not apply the compound excessively. Apply the compound to the counterbore and to the metal shell. Do NOT allow the compound to contact the sealing lip.
Install double lip wiper seal (1) into the cylinder head. Surface (1B) must face the rod end. There are no raised markings on the seal. Refer to Illustration 1 for the correct assembly position. The seal should be firmly seated against the bottom of the counterbore. Wipe away any excess bearing mount compound. Allow the compound to dry for 15 minutes before assembling the hydraulic cylinder.
Lightly lubricate the seals with clean hydraulic fluid before installing the head on the cylinder rod.
This instruction gives the procedure for installing the double lip wiper seal in the head of hydraulic cylinders.Installation of the Seal
Illustration 1 g00997424
Use sandpaper or emery cloth to scuff the surfaces of the counterbore in the cylinder head and the outside diameter (1A) of the wiper seal's metal shell.
Clean the counterbore in head (2) and the outside diameter (1A) of the wiper seal's metal shell with 8T-9011 Component Cleaner or 6V-1541 Quick Cure Primer . Clean the counterbore and the metal shell until neither of the components discolor a clean white towel.Note: The metal shell of the wiper seal is coated with a corrosion inhibitor. This may prevent proper bonding of the wiper seal to the cylinder head if the inhibitor is not removed. After cleaning, do not touch the counterbore or the metal shell because the oil from your fingers may prevent a good bond. Handle the seal by the lip only.
Apply 6V-1541 Quick Cure Primer on the counterbore and the metal shell. Allow the primer to dry. The primer will dry in approximately 30 seconds.
Apply 7M-7456 Bearing Mount Compound evenly but do not apply the compound excessively. Apply the compound to the counterbore and to the metal shell. Do NOT allow the compound to contact the sealing lip.
Install double lip wiper seal (1) into the cylinder head. Surface (1B) must face the rod end. There are no raised markings on the seal. Refer to Illustration 1 for the correct assembly position. The seal should be firmly seated against the bottom of the counterbore. Wipe away any excess bearing mount compound. Allow the compound to dry for 15 minutes before assembling the hydraulic cylinder.
Lightly lubricate the seals with clean hydraulic fluid before installing the head on the cylinder rod.
Parts pin Caterpillar catalog:
2412547
PIN-YM
Caterpillar
Caterpillar
2412542
PIN AS-YM
Caterpillar
Caterpillar
2412539
PIN AS-YM
Caterpillar
Caterpillar
Caterpillar
Caterpillar
2412531
PIN AS-YM
Caterpillar
Caterpillar
0000497
PIN-DOWEL
Caterpillar
Caterpillar
0000296
PIN
Caterpillar
Caterpillar
0000212
PIN
Caterpillar
Caterpillar
0000211
PIN
Caterpillar
Caterpillar
0000208
PIN-ROD END
Caterpillar
Caterpillar
0000136
PIN
Caterpillar
Caterpillar