4E0448 PIN-CLEVIS Caterpillar parts
CB-614, CP-433B, IT12B, IT14G, IT18F, IT24F, IT28F
Rating:
Alternative (cross code) number:
CA4E0448
4E-0448
4E0448
CA4E0448
4E-0448
4E0448
Weight: 0.02 pounds 0 kg.
Information:
EFFECTIVE LENGTH
48
mm
HEAD OD
7.9
mm
OVERALL LENGTH
52.5
mm
PIN OD
4.65
mm
TRANSV HOLES
Y
DETENT BALL
N
END TYPE A
RADIUS
END TYPE B
CHAMFER
GROOVE
N
HAND RING
N
HEAD THICKNESS
1.5
KEEPER SLOT
N
LUBE OUTLETS
N
COATING/PLATING
1E0397B
INTEGRATED TOOLCARRIER, VIBRATORY COMPACTOR,
Compatible equipment models: 4E0448:
Number on catalog scheme:
27
For full view, you need register
Information:
TECHNICAL INFORMATION BULLETIN December 22, 2004
All Caterpillar Products
Component Code: 7606SUBJECT: New PC Service Tool Software Released for Cellular Based Product Link (PL102C)
PROBLEM
Unexpected Behavior in PL102C Product Watch functionality ? Product Watch is disabled when a registration parameter is changed.
SCOPE
Root cause of the problem is an issue with the PC Service Tool that was distributed on CD with PL102C service cables (100% of population). There were approximately 100 of these CD/Service Cable combinations shipped to about 35 dealers. This will only affect users that enable the Product Watch feature.
SOLUTION
Update the PC Service Tool software to the latest release found on the SIS website. Note: The original software must be removed before installing the updated software.
A new version of PC Service Tool software has been validated and is ready for distribution to address the problem. The new software, EERE5001 (ver. 1.0.2), can be downloaded from the SISweb Internet site. From the main page under the "Highlights" section, click on "Downloads" and scroll down to "Additional Downloads".
Illustration 1
Illustration 2
Record the folder location where the file was saved.
PROCEDURE
Install the new PL102C Service Tool software. Note: If you have previously installed an earlier version of the Product Link PL102C Service Tool, you must first uninstall the older version. To uninstall the software, click on "Start", "Settings", "Control Panel", and "Add/Remove Software".
Illustration 3
Scroll down the "Add/Remove Programs" list until you locate the Caterpillar Service Tool. Click on "Remove". Answer "Yes" to the pop-up, "are you sure you want to remove".
Illustration 4
Locate the previously saved compressed zip file. Extract the compressed files and double-click on "Setup.exe".
Illustration 5
An icon will be placed on your desktop that looks like this:
Illustration 6
Connect the serial service cable (249-6476) between the PC and the 4-pin harness connector near the PL-102 module. Start the PC Service Tool application.
Verify and/or reset the Product Watch parameters. Refer to RENR8115, Systems Operation, "Configure PL102C Module Property Parameters" for configuration information.
COPYRIGHT 2004 CATERPILLAR
ALL RIGHTS RESERVED
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
9V1570
PIN
IT18F, IT24F, IT28, IT28F
IT18F, IT24F, IT28, IT28F
918F, 924F, 928F, 928G, 928H, 928HZ, IT18F, IT24F, IT28F, IT28G
5V4999
PIN
5130B, 902, 906, 910E, 910G, 914G, 918F, 924F, 924G, 924GZ, 924H, 924HZ, 926, 928F, 928G, 928H, 928HZ, 930G, 936, 936F, 938F, 938G, 938G II, 938H, D10, G936, IT12B, IT14B, IT14F, IT14G, IT14G2, IT18F,...
5130B, 902, 906, 910E, 910G, 914G, 918F, 924F, 924G, 924GZ, 924H, 924HZ, 926, 928F, 928G, 928H, 928HZ, 930G, 936, 936F, 938F, 938G, 938G II, 938H, D10, G936, IT12B, IT14B, IT14F, IT14G, IT14G2, IT18F,...
928F, IT28F
924G, 924GZ, 924H, 924HZ, 924K, 928F, 928G, 928H, 928HZ, 930G, 930K, IT28F, IT28G
4E3087
PIN-LATCH
844, 918F, 924F, 928F, 990, 990 II, IT18F, IT24F, IT28F
844, 918F, 924F, 928F, 990, 990 II, IT18F, IT24F, IT28F
IT18, IT18B, IT18F, IT24F, IT28, IT28B, IT28F
515, 525, 926, 926A, 928F, IT18B, IT18F, IT24F, IT28, IT28B, IT28F
IT18F, IT24F, IT28F
IT18, IT18B, IT18F, IT24F, IT28, IT28B, IT28F
916, IT18, IT18B, IT18F, IT24F, IT28, IT28B, IT28F
IT18, IT18B, IT18F, IT24F, IT28, IT28B, IT28F