9C6016 PINION-DIFFERENTIAL BEVEL Caterpillar parts
2470C, 2570C, 2670C, 2864C, 525B, 525C, 525D, 533, 535B, 535C, 535D, 543, 545, 545C, 545D, 553C, 555D, 563C, 573C, 586C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 950G, 950G II, 950H, 9...
Rating:
Alternative (cross code) number:
CA9C6016
9C-6016
9C6016
CA9C6016
9C-6016
9C6016
Weight: 2 pounds 1 kg.
INDUSTRIAL TRACTOR, WHEEL SKIDDER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 9C6016:
Information:
Remove Oil Pump
start by: a) remove fuel transfer pump 1. Remove six bolts (1) and adapter (2). 2. Remove oil pump drive gear (3) from the accessory drive housing. 3. Remove two bolts and clamp (8). Remove bolts (4), (5) and (10). Remove tee (7), tube (6) and oil pressure regulator (9). 4. Fasten a hoist to the oil pump. Remove bolt (12). Remove six bolts (11) that fasten the oil pump to the accessory drive housing. Remove the oil pump. The weight of the oil pump is 110 lb. (49.5 kg). 5. Remove bearing (13) from adapter (2).Install Oil Pump
1. Install a new gasket between oil pump (1) and accessory drive housing. Inspect and make a replacement of O-ring seal (2) if necessary. Fasten a hoist to the oil pump and install it. Install the six bolts which fasten the pump to the accessory drive. The weight of oil pump is 110 lb. (49.5 kg). 2. Install bolt (3) and remove hoist. 3. Inspect and make a replacement of O-ring seals on the tube, tee and oil pressure regulator. Install tube (5), tee (4) and oil pressure regulator (7). Install clamp (6) with two bolts. 4. Install oil pump drive gear (8) in the accessory drive housing. 5. Use a press and tooling (A) to install the bearing in adapter (9). 6. Install a new gasket between the accessory drive housing and adapter (9). Install the adapter with six bolts.end by: a) install fuel transfer pumpDisassemble Oil Pump
start by: a) remove oil pump 1. Remove bolts (1) and plate (2). 2. Remove bolts (3) and cover (4). 3. Remove nine bolts (5). 4. Make a separation of housing (6), manifold (7) and manifold (8). 5. Remove lip type seal (10) and bearing (9) from housing (6). 6. Remove shaft assembly (13), gears (12) and retainer (11) from manifold (8). 7. Remove two shafts (14) from the manifold with tooling (A) as shown. Remove bearing (15) from the manifold. 8. Use a press and tooling (B) to remove the bearing from retainer (11). 9. Use a press to remove gear (16) from shaft (13). 10. Use a press and tooling (B) to remove the bearings from gears (12).Assemble Oil Pump
1. Use tooling (A) and a press to install bearing (1) in retainer (2). 2. Install two bearings in each gear (3) with tooling (A) and press. Install the bearings until they are even with the surface of the gear. 3. Lower the temperature of shaft (4). Install the key in the shaft and install the shaft in gear (5) with a press until the gear makes contact with the shoulder on the shaft. 4. Lower the temperature of two shafts (6) and install in manifold (7). Install the bearing in the manifold with tooling (A). The installed bearing must be .030 in. (0.76 mm) below the machined surface of the manifold. 5. Install lip type seal in housing (8) with tooling (A). Install the seal with the
start by: a) remove fuel transfer pump 1. Remove six bolts (1) and adapter (2). 2. Remove oil pump drive gear (3) from the accessory drive housing. 3. Remove two bolts and clamp (8). Remove bolts (4), (5) and (10). Remove tee (7), tube (6) and oil pressure regulator (9). 4. Fasten a hoist to the oil pump. Remove bolt (12). Remove six bolts (11) that fasten the oil pump to the accessory drive housing. Remove the oil pump. The weight of the oil pump is 110 lb. (49.5 kg). 5. Remove bearing (13) from adapter (2).Install Oil Pump
1. Install a new gasket between oil pump (1) and accessory drive housing. Inspect and make a replacement of O-ring seal (2) if necessary. Fasten a hoist to the oil pump and install it. Install the six bolts which fasten the pump to the accessory drive. The weight of oil pump is 110 lb. (49.5 kg). 2. Install bolt (3) and remove hoist. 3. Inspect and make a replacement of O-ring seals on the tube, tee and oil pressure regulator. Install tube (5), tee (4) and oil pressure regulator (7). Install clamp (6) with two bolts. 4. Install oil pump drive gear (8) in the accessory drive housing. 5. Use a press and tooling (A) to install the bearing in adapter (9). 6. Install a new gasket between the accessory drive housing and adapter (9). Install the adapter with six bolts.end by: a) install fuel transfer pumpDisassemble Oil Pump
start by: a) remove oil pump 1. Remove bolts (1) and plate (2). 2. Remove bolts (3) and cover (4). 3. Remove nine bolts (5). 4. Make a separation of housing (6), manifold (7) and manifold (8). 5. Remove lip type seal (10) and bearing (9) from housing (6). 6. Remove shaft assembly (13), gears (12) and retainer (11) from manifold (8). 7. Remove two shafts (14) from the manifold with tooling (A) as shown. Remove bearing (15) from the manifold. 8. Use a press and tooling (B) to remove the bearing from retainer (11). 9. Use a press to remove gear (16) from shaft (13). 10. Use a press and tooling (B) to remove the bearings from gears (12).Assemble Oil Pump
1. Use tooling (A) and a press to install bearing (1) in retainer (2). 2. Install two bearings in each gear (3) with tooling (A) and press. Install the bearings until they are even with the surface of the gear. 3. Lower the temperature of shaft (4). Install the key in the shaft and install the shaft in gear (5) with a press until the gear makes contact with the shoulder on the shaft. 4. Lower the temperature of two shafts (6) and install in manifold (7). Install the bearing in the manifold with tooling (A). The installed bearing must be .030 in. (0.76 mm) below the machined surface of the manifold. 5. Install lip type seal in housing (8) with tooling (A). Install the seal with the
Cat SIS web machinery list:
Parts pinion Caterpillar catalog:
8R1703
PINION-DIFFERENTIAL BEVEL
515, 525, 918F, 924F, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 936F, 938F, 938G, 938G II, 950 GC, 950F, 950F II, 950G, 960F, 962G, IT18F, IT24F, IT28F, IT28G, IT38F, IT38G, IT38G II, R1300, ...
515, 525, 918F, 924F, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 936F, 938F, 938G, 938G II, 950 GC, 950F, 950F II, 950G, 960F, 962G, IT18F, IT24F, IT28F, IT28G, IT38F, IT38G, IT38G II, R1300, ...
5V5917
PINION-DIFFERENTIAL BEVEL
611, 615, 615C, 815B, 950B, 966D, D25C, D25D, D30C, D350C, D35C, D35HP, D400
611, 615, 615C, 815B, 950B, 966D, D25C, D25D, D30C, D350C, D35C, D35HP, D400
1043353
PINION-BEVEL
950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
1027510
PINION-DIFFERENTIAL BEVEL
966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K, IT38G II
966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K, IT38G II
8R8739
PINION-DIFFERENTIAL BEVEL
966F, 966F II, 970F
966F, 966F II, 970F
9C6023
PINION-DIFFERENTIAL BEVEL
545, 545C, 824C, 825C, 826C, 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE, 980C, 980F, R1700 II
545, 545C, 824C, 825C, 826C, 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE, 980C, 980F, R1700 II
2514250
PINION-BEVEL
545D, 555D, 966H, 972G II, 972H, 972K
545D, 555D, 966H, 972G II, 972H, 972K
4V5398
PINION
966D
966D
3622861
PINION-INPUT
2470C, 2570C, 2670C, 2864C, 553C, 563C, 573C, 586C
2470C, 2570C, 2670C, 2864C, 553C, 563C, 573C, 586C
9C6015
PINION-DIFFERENTIAL BEVEL
814B, 815B
814B, 815B
1350352
PINION AS
651E, 657E, 657G
651E, 657E, 657G
1122254
PINION AS
631E
631E
1046740
PINION
924K, 928F, 928G, 928HZ, 930G, 930K, IT28F, IT28G
924K, 928F, 928G, 928HZ, 930G, 930K, IT28F, IT28G
1094718
PINION-DIFFERENTIAL
910G, 914G, IT14G, IT14G2
910G, 914G, IT14G, IT14G2
1046749
PINION-DIFFERENTIAL BEVEL
924F, 924G, 924GZ, 924H, 924HZ, IT18F, IT24F
924F, 924G, 924GZ, 924H, 924HZ, IT18F, IT24F
1046732
PINION-DIFFERENTIAL BEVEL
936F, 938F, 938G, 938G II, IT38F, IT38G, IT38G II
936F, 938F, 938G, 938G II, IT38F, IT38G, IT38G II
2527932
PINION-DIFFERENTIAL
924H, 924HZ, 924K, 928HZ, 930K
924H, 924HZ, 924K, 928HZ, 930K
3853634
PINION
914G, IT14G, IT14G2
914G, IT14G, IT14G2
1027510
PINION-DIFFERENTIAL BEVEL
966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K, IT38G II
966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K, IT38G II
2087877
PINION-BEVEL
902, 906, 908, CP-433E, CS-323C, CS-423E, CS-44
902, 906, 908, CP-433E, CS-323C, CS-423E, CS-44
2206022
PINION-BEVEL
902, 906, 906H, 906H2, 907H, 907H2, 908, 908H, 908H2
902, 906, 906H, 906H2, 907H, 907H2, 908, 908H, 908H2
1043353
PINION-BEVEL
950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H