2444036 PLATE-WEAR Caterpillar parts
315C, 315D L
Rating:
Alternative (cross code) number:
CA2444036
244-4036
2444036
CA2444036
244-4036
2444036
EXCAVATOR,
Number on catalog scheme:
4
For full view, you need register
Information:
Worm Drive Band Type Clamps
Illustration 1 g00910017
Table 1
Width (A) of Clamp Torque for New Hose
7.5 mm (0.3 inch) or greater 1.4 0.3 N m (12 3 lb in)
12 mm (0.5 inch) or greater 4.5 0.7 N m (40 6 lb in)
14 mm (0.6 inch) or greater 7.5 1 N m (66 9 lb in)
Width (A) of Clamp Torque for Reused Hose(1)
7.5 mm (0.3 inch) or greater 0.8 0.3 N m (7 3 lb in)
12 mm (0.5 inch) or greater 3.0 0.5 N m (27 4 lb in)
14 mm (0.6 inch) or greater 4.5 0.7 N m (40 6 lb in)
(1) Use this value when the hose is reused. The clamp may be new or reused.Constant Torque Hose Clamps
Use a constant torque hose clamp in place of any worm drive band type clamp. Ensure that the constant torque hose clamp is the same size as the worm drive band type clamp. Due to extreme temperature changes, the hose will heat set. Heat setting can cause worm drive band type clamps to loosen. Loose hose clamps can result in leaks. There have been reports of component failures that have been caused by worm drive band type clamps that have loosened. The constant torque hose clamp will help prevent these failures.
Illustration 2 g03076961
(1) Constant Torque Hose Clamp (Belleville Washer)
(2) Constant Torque Hose Clamp (Tee bolt and Spring)Use a torque wrench for proper installation of all constant torque hose clamps. There are two types of constant torque hose clamps: Belleville washer (1) and Tee bolt and spring (2)When the constant torque hose clamp (Belleville washer) (1) is assembled correctly, the Belleville washers (1A) are nearly collapsed flat. The proper torque for screw (1B) is based on the diameter (B) of the clamp. Refer to the following table for the correct torque.
Table 2
Constant Torque Hose Clamps
Clamp Type Diameter (B) Standard Torque
Constant Torque Hose Clamp (Belleville Washer) (1) Up to 50.8 mm (2 inch) 7.5 1 N m (65 10 lb in)
Greater than 50.8 mm (2 inch) 11 1 N m (95 10 lb in)
Constant Torque Hose Clamp (Tee bolt and Spring) (2) N/A 7.5 1 N m (65 10 lb in) Wave Liner Clamps
The wave liner worm drive clamp is a clamp with a special liner. this liner has a "v grove" that causes greater pressure points on the hose. This greater compression will offer better sealing capability at the hose connection.
Illustration 3 g03869499
Table 3
Width (A) of Clamp Torque for New Hose
14 mm (0.6 inch) or greater 7.5 1 N m (66.4 8.9 lb in)
Illustration 1 g00910017
Table 1
Width (A) of Clamp Torque for New Hose
7.5 mm (0.3 inch) or greater 1.4 0.3 N m (12 3 lb in)
12 mm (0.5 inch) or greater 4.5 0.7 N m (40 6 lb in)
14 mm (0.6 inch) or greater 7.5 1 N m (66 9 lb in)
Width (A) of Clamp Torque for Reused Hose(1)
7.5 mm (0.3 inch) or greater 0.8 0.3 N m (7 3 lb in)
12 mm (0.5 inch) or greater 3.0 0.5 N m (27 4 lb in)
14 mm (0.6 inch) or greater 4.5 0.7 N m (40 6 lb in)
(1) Use this value when the hose is reused. The clamp may be new or reused.Constant Torque Hose Clamps
Use a constant torque hose clamp in place of any worm drive band type clamp. Ensure that the constant torque hose clamp is the same size as the worm drive band type clamp. Due to extreme temperature changes, the hose will heat set. Heat setting can cause worm drive band type clamps to loosen. Loose hose clamps can result in leaks. There have been reports of component failures that have been caused by worm drive band type clamps that have loosened. The constant torque hose clamp will help prevent these failures.
Illustration 2 g03076961
(1) Constant Torque Hose Clamp (Belleville Washer)
(2) Constant Torque Hose Clamp (Tee bolt and Spring)Use a torque wrench for proper installation of all constant torque hose clamps. There are two types of constant torque hose clamps: Belleville washer (1) and Tee bolt and spring (2)When the constant torque hose clamp (Belleville washer) (1) is assembled correctly, the Belleville washers (1A) are nearly collapsed flat. The proper torque for screw (1B) is based on the diameter (B) of the clamp. Refer to the following table for the correct torque.
Table 2
Constant Torque Hose Clamps
Clamp Type Diameter (B) Standard Torque
Constant Torque Hose Clamp (Belleville Washer) (1) Up to 50.8 mm (2 inch) 7.5 1 N m (65 10 lb in)
Greater than 50.8 mm (2 inch) 11 1 N m (95 10 lb in)
Constant Torque Hose Clamp (Tee bolt and Spring) (2) N/A 7.5 1 N m (65 10 lb in) Wave Liner Clamps
The wave liner worm drive clamp is a clamp with a special liner. this liner has a "v grove" that causes greater pressure points on the hose. This greater compression will offer better sealing capability at the hose connection.
Illustration 3 g03869499
Table 3
Width (A) of Clamp Torque for New Hose
14 mm (0.6 inch) or greater 7.5 1 N m (66.4 8.9 lb in)
Caterpillar parts catalog:
Parts plate Caterpillar catalog:
14G, 215, 215B, 215C, 215D, 225, 225D, 229, 229D, 231D, 235, 235B, 235C, 235D, 245, 245B, 24H, 24M, 307C, 311C, 311D LRR, 311F LRR, 312, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 3...
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 315, 315B, 315C, 317B LN, 318B, 906, 90...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 307, 307B, 307D, 307E, 308E, 311, 311B, 311C, 312, 312B, 312B L, 312C L, 313B, 314C, 315, 315B, 315B FM L, 315C, 317, 318B, 318C, 319C, 320 L, 320B, 3...
115, 312, 315, 315C, 317, 318B, 318C, 319C, 319D, 319D LN, 320 L, 320B, 320C, 320C L, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321C...
315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM ...
311C, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 32...
1290T, 1390, 2491, 2590, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311D LRR, 311F LRR, 312C, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR...
311C, 313D2 LGP, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 3...
311C, 313D2 LGP, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 3...
315C, 315D L, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 3...
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L...
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L...
2444045
PLATE-WEAR
315C, 315D L
315C, 315D L
2444026
PLATE-REINFORCEMENT
315C, 315D L
315C, 315D L
2444044
PLATE-WEAR
315C, 315D L
315C, 315D L
2442745
PLATE-WEAR
315C, 315D L
315C, 315D L
1934773
PLATE
315C
315C
1934772
PLATE
315C
315C
2444043
PLATE-WEAR
315C, 315D L
315C, 315D L
2444048
PLATE-WEAR
315C, 315D L
315C, 315D L
2444042
PLATE-REINFORCEMENT
315C, 315D L
315C, 315D L
2444047
PLATE-WEAR
315C, 315D L
315C, 315D L
2444041
PLATE-REINFORCEMENT
315C, 315D L
315C, 315D L
2444046
PLATE-WEAR
315C, 315D L
315C, 315D L