RING-SEAL 1421739 - Caterpillar

Illustration 3 g03269576
Tooling (G)
418-3611 Track Block
Table 2
Required Tools
Tool Item Qty Part
Number Description
A 198-4240 Digital Pressure Indicator Gp
A1 1 198-4234 Indicator
A2 1 198-4237 Pressure Sensor
3447 kPa (500 psi)
A2 1 198-4239 Pressure Sensor
41,368 kPa (6,000 psi)
A3 2 198-4236 Extension Cable
D D1 1 6V-7788 Flow Meter
5 to 60 L/min (2 to 15 US gpm)
D2 1 8C-6874 Reducer
D3 1 6V-9746 O-Ring Seal
D4 1 124-1901 Permanent Coupling
D5 3 ft 122-6870 Bulk Hydraulic Hose
D6 1 124-2147 Permanent Coupling
D7 1 6V-8942 O-Ring Reducer
D8 1 6V-8556 Nut
D9 1 6V-8398 O-Ring Seal
F 1 311-1362 Vacuum Cap
G 1 418-3611 Track Block Machine Preparation
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Position the machine on level ground.
Illustration 4 g03267696
Sprocket (left travel)
(G) Track block
(1) Sprocket
Place track block (G) in sprocket (1) in order to block forward left travel. Refer to Illustration 4.
Stop the engine.
Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "Hydraulic System Pressure - Release".
Attach 311-1362 Vacuum Cap onto the hydraulic tank. Attach an air supply hose onto the assembly. Apply 276 to 414 kPa (40 to 60 psi). This procedure will pull a vacuum on the hydraulic system.
Illustration 5 g02240294
Flow Meter Tool Layout
Tooling (D)
( 2) Case drain hose
(3) Connector
(4) Travel motor
Install the following tools in accordance with the flow meter tool layout. Refer to Illustration 5.
Disconnect case drain hose (2) from connector (3).
Connect the flow meter assembly (D) between connector (3) and case drain hose (2). Note: Correct orientation of the flow meter is necessary. The oil flows from travel motor (4) to case drain hose (2).
Remove 311-1362 Vacuum Cap and install the filler plug for the hydraulic tank. Test Procedure
Start the engine.
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Move the left travel lever to full FORWARD position and check the flow of oil through the flow meter.
Remove track block (G) from sprocket (1).
Move the left travel lever in order to reposition the travel motor.
Place track block (G) in sprocket (1) in order to block forward left travel.
Repeat Steps 4 through 7 in order to obtain three measurements of case drain oil. The following values specify the maximum acceptable flow of case drain oil when the travel crossover relief valves are set at 37000 500 kPa (5366 73 psi). New travel motor ... 15 L/min (4.0 US gpm)Rebuilt travel motor ...