1807459 RING-BACKUP Caterpillar parts
330C, 330D L, 330D MH, 345B II, 345B II MH, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, W345B II, W345C MH
Rating:
Alternative (cross code) number:
CA1807459
180-7459
1807459
CA1807459
180-7459
1807459
Weight: 0.01 pounds 0 kg.
Information:
AXIAL WIDTH
.6
mm
ID
26.2
mm
MATERIAL
(PTFE) Plastic - Glass filled
OD
30
mm
RADIAL HEIGHT
1.9
mm
RING TYPE
OD
EXCAVATOR, WHEELED EXCAVATOR,
Compatible equipment models: 1807459:
Number on catalog scheme:
2
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description QTY
A 5P-0332 Crowfoot Wrench 1
B 129-1966 Multipurpose Grease 1 Start By:
Remove the exhaust sensor lines.
Contact with high pressure fuel may cause personal injury or death. Wait 60 seconds after the engine has stopped to allow fuel pressure to purge before any service or repair is performed on the engine fuel lines.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Turn the fuel supply to the OFF position.
Disconnect the battery. Refer to Operation and Maintenance Manual, "Battery or Battery Cable - Disconnect".
Remove all components in order to access to the harness assembly.
Illustration 1 g02796524
Loosen clamp assemblies (1) and remove hose (2).
Illustration 2 g02140852
Disconnect fittings (3) and (7).
Remove bolts (5), (6), and (8) and remove tube assembly (4).
Remove bolt (9).
Illustration 3 g02796529
Remove nuts (10) and remove bracket (11).
Disconnect harness assemblies (12).
Illustration 4 g02141940
Typical Example
Illustration 5 g02141948
Illustration 6 g02156903
Position harness assembly (13) out of the way with cable straps.
Disconnect tube assembly (16) and remove fitting (15). Note: Relief valve (14) is a two-piece valve which should not be disassembled.Note: Do not use Tooling (A) at Location (X).
Use Tooling (A) to remove relief valve (14) and remove the O-ring seal. Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Install relief valve (14) in the reverse order of removal.
Apply Tooling (B) to the threads of relief valve (14). Use Tooling (A) to tighten relief valve (14) to a torque of 60 5 N m (44 4 lb ft).
Loosen relief valve (14) to a torque of 5 3 N m (44 27 lb in).
Again, tighten relief valve (14) to a torque of 20 2 N m (177 18 lb in).
Tighten relief valve (14) an additional 18° turn. Again, Tighten relief valve (14) to a torque of 90 20 N m (66 15 lb ft).
Table 1
Required Tools
Tool Part Number Part Description QTY
A 5P-0332 Crowfoot Wrench 1
B 129-1966 Multipurpose Grease 1 Start By:
Remove the exhaust sensor lines.
Contact with high pressure fuel may cause personal injury or death. Wait 60 seconds after the engine has stopped to allow fuel pressure to purge before any service or repair is performed on the engine fuel lines.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Turn the fuel supply to the OFF position.
Disconnect the battery. Refer to Operation and Maintenance Manual, "Battery or Battery Cable - Disconnect".
Remove all components in order to access to the harness assembly.
Illustration 1 g02796524
Loosen clamp assemblies (1) and remove hose (2).
Illustration 2 g02140852
Disconnect fittings (3) and (7).
Remove bolts (5), (6), and (8) and remove tube assembly (4).
Remove bolt (9).
Illustration 3 g02796529
Remove nuts (10) and remove bracket (11).
Disconnect harness assemblies (12).
Illustration 4 g02141940
Typical Example
Illustration 5 g02141948
Illustration 6 g02156903
Position harness assembly (13) out of the way with cable straps.
Disconnect tube assembly (16) and remove fitting (15). Note: Relief valve (14) is a two-piece valve which should not be disassembled.Note: Do not use Tooling (A) at Location (X).
Use Tooling (A) to remove relief valve (14) and remove the O-ring seal. Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Install relief valve (14) in the reverse order of removal.
Apply Tooling (B) to the threads of relief valve (14). Use Tooling (A) to tighten relief valve (14) to a torque of 60 5 N m (44 4 lb ft).
Loosen relief valve (14) to a torque of 5 3 N m (44 27 lb in).
Again, tighten relief valve (14) to a torque of 20 2 N m (177 18 lb in).
Tighten relief valve (14) an additional 18° turn. Again, Tighten relief valve (14) to a torque of 90 20 N m (66 15 lb ft).
Cat SIS web machinery list:
Parts ring Caterpillar catalog:
320C, 325B L, 325C, 325C L, 325D MH, 330C, M325B
323D L, 323D LN, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D, 325D FM, 325D L, 329D L, 329D LN, 329E L, 329E LN, 330D L
323D L, 323D LN, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D, 325D FM, 325D L, 329D L, 329D LN, 329E L, 329E LN, 330D L
323D L, 323D LN, 324D, 324D FM, 324D L, 324D LN, 324E L, 324E LN, 325D, 325D FM, 325D L, 329D L, 329D LN, 329E L, 329E LN, 330D L
323D L, 323D2 L, 324D, 324D L, 324D LN, 324E LN, 325C, 325D, 325D L, 329D L, 329D LN, 329E L, 329E LN, 330B L, 330C, 330C L, 330D L, 330D LN, 336D L, 336D LN, 336D2 L, 336E LN, 345B II, 345C, 345C L, ...
325 L, 325C, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 345B II, 345C, 345C L, 365B, 365B II, 365B L, 365C, 36...
321C, 325C, 328D LCR, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, ...
345C, 345C L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, D10, D9G, D9H
325C, 328D LCR, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN
330, 345B, 345B II, 345B L, 345C, 345C L, 350, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH
325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C FM, 330D FM, 345B II, 345B L, 345C, 350, 350 L, 365B, 365B II, M325B, M325C MH, M325D L MH
345B II, 345B L, 345C, 365B
345B II, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E L, 349E L VG, 349F L, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390...
345B II, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E L, 349E L VG, 349F L, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C L, 390D, 390D L, 390...
330C, 330D L, 330D MH, 345B II, 345B II MH, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 374D L, 374F L
330C, 330D L, 330D MH, 345B II, 345B II MH, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 374D L, 374F L
2059024
RING-TORIC
330C, 330D L, 330D MH, 345B II, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L
330C, 330D L, 330D MH, 345B II, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L
2197828
RING AS
330C
330C
365C, 365C L, 365C L MH, 374D L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L
2478785
RING
365C, 365C L, 365C L MH, 374D L
365C, 365C L, 365C L MH, 374D L
2453808
RING-THRUST
345C, 345C L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L
345C, 345C L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L
1362943
RING-RETAINING
345B II, 345C, 345C L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L
345B II, 345C, 345C L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L
2147879
RING-TORIC
345B II, 345C, 345C L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L
345B II, 345C, 345C L, 365B, 365B II, 365C, 365C L, 365C L MH, 374D L, 374F L
330, 345B, 345B II, 345B L, 345C, 345C L, 350, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH