1989428 SEAL Caterpillar parts
305, 305.5, 306
Rating:
Alternative (cross code) number:
CA1989428
198-9428
1989428
CA1989428
198-9428
1989428
Weight: 0.01 pounds 0 kg.
MINI HYD EXCAVATOR,
Information:
+
Determine the location for the placement of the Product Link. Before you weld or before you drill, check that the location will not invalidate the structure certification for the following items: ROPS, FOPS and other protective structures. Refer to Special Instruction, SEHS6929, "Inspection, Maintenance and Repair of Rollover Protective Structures (ROPS) and Attachment Installation Guidelines" as well as any other published guidelines that are specific for a serial number.
Do NOT install the unit in the following locations:
Do not attach to the underside of the machine.
Do not attach in a location that obstructs the view of the operator.
Do not attach to the ROPS by drilling holes through the structure.
Do not attach to the ROPS by welding to the structure.
Do not attach to the roof, unless no other location is available.
Do not attach if there is any exposure to water.
Do not attach with connectors that point upward in order to avoid collecting water.
Do not attach to a location that is subject to abrasion by debris.
Do not attach in the engine compartment unless the factory is in approval.
Structural damage, an overturn, modification, alteration, or improper repair can impair this structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a Caterpillar dealer to determine this structure's limitations without voiding its certification.
When you select the location, remember the following consideration:
The Product Link Module will be connected to an antenna that is mounted on the roof. Keep the routing of the cable in mind. The length of the antenna cable is 6.07 m (20 ft) or 0.91 m (3 ft).
The antenna cable must not be routed near the exhaust system.
The antenna cable must not be bent sharply.
Determine if the shock mounting will be used. Shock mounting is required on all track-type vehicles. On all other machines, shock mounts are not required if the unit is being installed in a cab that has shock mounts. If the unit is being installed outside the cab or if the cab does not have shock mounts, the shock mounts must be used.
Illustration 1 g00695514
Installation with shock mounts (sample)
Illustration 2 g00695517
Sample installation location on shock-mounted cab
Illustration 3 g00658132
Dimensions For Attaching Weld Bosses For The Product Link
If the mounting location is thick metal or if drilling holes is not desired, attach the four 4E-8266 Bosses in the pattern that is shown in Illustration 3. Note the different measurements for non-shock mounted units. If the mounting location is not metal or if drilling holes is easy, drill four 6.35 mm (0.25 inch) holes through the mounting surface.
Illustration 4 g00656866
Shock Mounting (1) 8C-5607 Mount (2) 170-9198 Plate (3) 8C-5608 Spacer
Assemble the shock mounting components. Push a 8C-5607 Mount (1) into the 15 mm (0.59 inch) hole in each side of the 170-9198 Plate (2). Slide a 8C-5608 Spacer (3) inside the two mounts. Repeat this procedure for the remaining three holes.
Illustration 5 g00657475
Attach the mounting plates to the Product Link Module by using screws (4) .
Illustration 6 g00657481
Illustration 7 g00657485
Side View Of Properly Assembled
Determine the location for the placement of the Product Link. Before you weld or before you drill, check that the location will not invalidate the structure certification for the following items: ROPS, FOPS and other protective structures. Refer to Special Instruction, SEHS6929, "Inspection, Maintenance and Repair of Rollover Protective Structures (ROPS) and Attachment Installation Guidelines" as well as any other published guidelines that are specific for a serial number.
Do NOT install the unit in the following locations:
Do not attach to the underside of the machine.
Do not attach in a location that obstructs the view of the operator.
Do not attach to the ROPS by drilling holes through the structure.
Do not attach to the ROPS by welding to the structure.
Do not attach to the roof, unless no other location is available.
Do not attach if there is any exposure to water.
Do not attach with connectors that point upward in order to avoid collecting water.
Do not attach to a location that is subject to abrasion by debris.
Do not attach in the engine compartment unless the factory is in approval.
Structural damage, an overturn, modification, alteration, or improper repair can impair this structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a Caterpillar dealer to determine this structure's limitations without voiding its certification.
When you select the location, remember the following consideration:
The Product Link Module will be connected to an antenna that is mounted on the roof. Keep the routing of the cable in mind. The length of the antenna cable is 6.07 m (20 ft) or 0.91 m (3 ft).
The antenna cable must not be routed near the exhaust system.
The antenna cable must not be bent sharply.
Determine if the shock mounting will be used. Shock mounting is required on all track-type vehicles. On all other machines, shock mounts are not required if the unit is being installed in a cab that has shock mounts. If the unit is being installed outside the cab or if the cab does not have shock mounts, the shock mounts must be used.
Illustration 1 g00695514
Installation with shock mounts (sample)
Illustration 2 g00695517
Sample installation location on shock-mounted cab
Illustration 3 g00658132
Dimensions For Attaching Weld Bosses For The Product Link
If the mounting location is thick metal or if drilling holes is not desired, attach the four 4E-8266 Bosses in the pattern that is shown in Illustration 3. Note the different measurements for non-shock mounted units. If the mounting location is not metal or if drilling holes is easy, drill four 6.35 mm (0.25 inch) holes through the mounting surface.
Illustration 4 g00656866
Shock Mounting (1) 8C-5607 Mount (2) 170-9198 Plate (3) 8C-5608 Spacer
Assemble the shock mounting components. Push a 8C-5607 Mount (1) into the 15 mm (0.59 inch) hole in each side of the 170-9198 Plate (2). Slide a 8C-5608 Spacer (3) inside the two mounts. Repeat this procedure for the remaining three holes.
Illustration 5 g00657475
Attach the mounting plates to the Product Link Module by using screws (4) .
Illustration 6 g00657481
Illustration 7 g00657485
Side View Of Properly Assembled
Caterpillar parts catalog:
Parts seal Caterpillar catalog:
4J0520
SEAL-O-RING
153, 163, 1673C, 173B, 183B, 215, 216, 225, 225D, 228, 229, 229D, 231D, 235, 235B, 235C, 235D, 236, 245, 245B, 245D, 246C, 248, 256C, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 28...
153, 163, 1673C, 173B, 183B, 215, 216, 225, 225D, 228, 229, 229D, 231D, 235, 235B, 235C, 235D, 236, 245, 245B, 245D, 246C, 248, 256C, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 28...
6F4855
SEAL-O-RING
10 FT, 1090, 10B, 1140, 1145, 1150, 1160, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA...
10 FT, 1090, 10B, 1140, 1145, 1150, 1160, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA...
5P7814
SEAL-O-RING
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 135H, 135H NA, 140G, 140H, 140K, 140K 2, 140M, 143H, 14H, 160H, 160K, 163H, 16H, 216, 216B, 216B3, 226B, 226B3, 232B, 235, 236B, 236D, 242B, 242D, 245, 246D,...
120H, 120H ES, 120H NA, 120K, 120K 2, 12K, 135H, 135H NA, 140G, 140H, 140K, 140K 2, 140M, 143H, 14H, 160H, 160K, 163H, 16H, 216, 216B, 216B3, 226B, 226B3, 232B, 235, 236B, 236D, 242B, 242D, 245, 246D,...
2287089
SEAL-O-RING
120K, 120K 2, 120M 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 2290, 2384C, 2390, 2391, 2470C, 24...
120K, 120K 2, 120M 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 2290, 2384C, 2390, 2391, 2470C, 24...
3E6602
SEAL
303.5, 304.5, 305, 308E2 CR, 311D LRR, 568 FM LL, 621H, 795F AC, 795F XQ, 844, 844H, 854G, 854K, 933C, 939C, 950 GC, 950H, 950K, 962H, 962K, 966H, 966K, 966M, 966M XE, 972H, 972K, 972M, 972M XE, 980K,...
303.5, 304.5, 305, 308E2 CR, 311D LRR, 568 FM LL, 621H, 795F AC, 795F XQ, 844, 844H, 854G, 854K, 933C, 939C, 950 GC, 950H, 950K, 962H, 962K, 966H, 966K, 966M, 966M XE, 972H, 972K, 972M, 972M XE, 980K,...
0951586
SEAL-O-RING
1090, 1190, 1190T, 1290T, 1390, 2290, 2384C, 2390, 2391, 2484C, 2491, 2590, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D...
1090, 1190, 1190T, 1290T, 1390, 2290, 2384C, 2390, 2391, 2484C, 2491, 2590, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D...
0951592
SEAL-O-RING
2384C, 2484C, 301.5, 304, 304C CR, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 3...
2384C, 2484C, 301.5, 304, 304C CR, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 3...
0951591
SEAL-O-RING
305.5, 306, 307D, 308D, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LC...
305.5, 306, 307D, 308D, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LC...
0951579
SEAL-O-RING
2384C, 2484C, 302.5, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 307, 307B, 307C, 307D, 307E, 308...
2384C, 2484C, 302.5, 303, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304.5, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 307, 307B, 307C, 307D, 307E, 308...
0951709
SEAL-O-RING
2384C, 2484C, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304.5, 304C CR, 304D CR, 304E, 305, 305D CR, 305E, 308E, 308E CR, 308E SR, 311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 31...
2384C, 2484C, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304.5, 304C CR, 304D CR, 304E, 305, 305D CR, 305E, 308E, 308E CR, 308E SR, 311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 31...
1184808
SEAL-O-RING
303.5C, 304C CR, 304D CR, 305.5, 305C CR, 306, 307D, 315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
303.5C, 304C CR, 304D CR, 305.5, 305C CR, 306, 307D, 315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
1404743
SEAL-DUST
302.5, 303, 303.5, 304, 304.5, 305
302.5, 303, 303.5, 304, 304.5, 305
1989420
SEAL
305, 305.5, 306
305, 305.5, 306
2167246
SEAL
304, 305
304, 305
2167244
SEAL
303.5C, 304, 305
303.5C, 304, 305
2057956
SEAL AS
304, 305
304, 305
2057952
SEAL
304, 305
304, 305
2057950
SEAL
304, 305
304, 305
1990603
SEAL
304E, 305, 305.5, 306
304E, 305, 305.5, 306
1990598
SEAL
305, 305.5, 306
305, 305.5, 306
1990596
SEAL
305, 305.5, 306
305, 305.5, 306
1991147
SEAL
305, 305.5, 306
305, 305.5, 306
1991141
SEAL AS
305, 305.5, 306
305, 305.5, 306
1991139
SEAL
305, 305.5, 306
305, 305.5, 306