196-8719 CONVERSION GP-MACHINE -CUSTOM S/N BAB1-UP; AYL1-UP PART OF 198-4586, 233-7349 PROTECTION AR-CORROSION 950G II

196-8719: CONVERSION GP-MACHINE

196-8719 CONVERSION GP-MACHINE -CUSTOM
S/N BAB1-UP; AYL1-UP
PART OF 198-4586, 233-7349 PROTECTION AR-CORROSION

Parts for your 950G II WHEEL LOADER:

Part No	Qty	Parts name
		THE FOLLOWING ARE PART OF THE STANDARD CONTROL GP-BUCKET
163-2138	[2]	PIN AS
163-2140	[2]	PIN AS
163-2141	[2]	PIN AS
163-2142	[1]	PIN AS
163-2143	[1]	PIN AS
163-2145	[4]	PIN AS
163-2146	[1]	PIN AS

		THE FOLLOWING ARE PART OF THE STANDARD DOOR GP-BATTERY
163-5185	[1]	PLATE
163-5186	[1]	ROD AS

		THE FOLLOWING IS PART OF THE STANDARD LINES GP-FUEL
196-8724	[1]	BRACKET AS

		THE FOLLOWING ARE PART OF THE STANDARD SHIELD GP- ENGINE COMPARTMENT
185-4227	[1]	PLATE AS
196-8728	[1]	PLATE AS

		THE FOLLOWING ARE PART OF THE STANDARD WIRING GP-ENGINE
185-4217	[1]	BRACKET AS
196-8812	[1]	BRACKET AS

		THE FOLLOWING ARE PART OF THE STANDARD WIRING GP-AXLE MONITORING-OIL TEMPERATURE
223-5157	[2]	BRACKET
223-5158	[1]	BRACKET AS

		THE FOLLOWING IS PART OF THE STANDARD KICKOUT & POSITIONER GP
196-9089	[2]	PLATE
196-9090	[1]	PLATE

		THE FOLLOWING IS PART OF THE STANDARD CYLINDER & MTG GP-STEERING
178-4819	[4]	PIN AS

		THE FOLLOWING ARE PART OF THE STANDARD COUNTERWEIGHT GP
163-5202	[1]	PIN
219-3095	[1]	PIN

		THE FOLLOWING ARE PART OF THE STANDARD TILT GP-HOOD
229-2453	[1]	ACTUATOR AS

		THE FOLLOWING ARE PART OF THE STANDARD LINES GP-STEERING
163-8204	[1]	TUBE AS
196-8798	[1]	ANGLE AS
196-9103	[1]	BRACKET AS
196-9106	[1]	TUBE AS
196-9108		TUBE AS
223-5798	[2]	BRACKET AS

		THE FOLLOWING IS PART OF STANDARD HORN GP-ELECTRIC
205-5152	[1]	BRACKET

		THE FOLLOWING ARE PART OF THE FILLER GP-POWER TRAIN OIL
163-5268	[1]	TUBE AS
163-5269	[1]	TUBE AS

		THE FOLLOWING ARE PART OF THE STANDARD CONTROL GP-SERVICE BRAKE
165-3515	[2]	CLIP
196-8794	[1]	BRACKET AS
196-8798	[1]	ANGLE AS
196-9097	[1]	BRACKET AS
213-7101	[1]	BRACKET AS
223-4650	[1]	BRACKET AS

		THE FOLLOWING ARE PART OF THE STANDARD BATTERY & WIRING GP
223-4652	[1]	BRACKET AS
223-4653	[1]	BRACKET AS

		THE FOLLOWING IS PART OF THE STANDARD LINES GP-HYDRAULIC
163-8206	[1]	TUBE AS

		THE FOLLOWING ARE PART OF THE STANDARD LINES GP-TORQUE CONVERTER COOLER
196-9076	[1]	TUBE AS
196-9078	[1]	BRACKET AS
196-9079	[2]	BRACKET AS
		(EACH INCLUDES)
191-2449	[1]	PLATE AS
8T-3490 M	[1]	NUT-WELD (M10X1.5 THD)
196-9081	[1]	BRACKET AS

		THE FOLLOWING IS PART OF THE STANDARD PUMP & MOUNTING GP
233-1450	[1]	BRACKET AS

		THE FOLLOWING IS PART OF THE STANDARD PUMP & MOUNTING GP- HYDRAULIC FAN
196-9082	[1]	BRACKET AS

		THE FOLLOWING ARE A PART OF THE STANDARD PROTECTION GP-VANDALISM
195-1875	[1]	COVER GP-PROTECTIVE
1L-5072	[2]	DOWEL
2J-7761	[2]	RING-RETAINING
195-1871	[2]	LEVER
195-1873	[1]	CAP AS-FILLER
195-1874	[1]	CAP AS-FILLER

		THE FOLLOWING IS PART OF THE STANDARD TANK GP-FUEL
	[1]	CAP AS-FUEL

		THE FOLLOWING IS PART TO THE STANDARD FUMES DISPOSAL GP
163-5194	[1]	BRACKET

		THE FOLLOWING ARE PART OF THE STANDARD LINES GP-HYDRAULIC OIL COOLER
	[1]	ANGLE
209-2285	[1]	BRACKET
230-9363	[1]	BRACKET

		THE FOLLOWING IS PART OF THE STANDARD ACTUATOR GP-PARKING BRAKE
223-5604	[1]	BRACKET AS

		THE FOLLOWING ARE PART OF THE STANDARD LINES GP-PILOT
185-4263	[2]	PLATE
196-9093	[1]	BRACKET AS
196-9096	[1]	BRACKET AS
196-9099	[1]	BRACKET AS


		***ATTACHMENT REMOVAL***

		THE FOLLOWING IS PART OF THE STANDARD PROTECTION GP-VANDALISM
7K-5636	[1]	COVER GP-TMSN OIL FILLER CAP

		***STANDARD REMOVAL***

		THE FOLLOWING ARE PART OF THE STANDARD CONTROL GP-BUCKET
4E-3196	[2]	PIN AS
5V-1508	[2]	PIN AS
5V-1511	[2]	PIN AS
5V-1882	[1]	PIN AS
9C-0093	[1]	PIN AS
136-9371	[4]	PIN AS
136-9380	[1]	PIN AS

		THE FOLLOWING IS PART OF STANDARD PUMP & MOUNTING GP-HYDRAULIC
144-7913	[1]	BRACKET AS

		THE FOLLOWING ARE PART OF THE STANDARD DOOR GP-BATTERY
153-0150	[1]	PLATE
	[1]	ROD AS

		THE FOLLOWING IS PART OF THE STANDARD LINES GP-FUEL
191-2345	[1]	BRACKET AS

		THE FOLLOWING ARE PART OF THE STANDARD SHIELD GP-ENGINE COMPARTMENT
121-7885	[1]	PLATE AS
193-0211	[1]	PLATE AS

		THE FOLLOWING ARE PART OF THE STANDARD WIRING GP-ENGINE
116-4491	[1]	BRACKET AS
118-6878	[1]	BRACKET AS

		THE FOLLOWING ARE PART OF THE STANDARD WIRING GP-AXLE MONITORING, OIL TEMPERATURE
156-5892	[2]	BRACKET
214-3319	[1]	BRACKET AS

		THE FOLLOWING IS PART OF THE STANDARD TILT GP-HOOD
210-2613	[1]	ACTUATOR GP-HOOD TILT

		THE FOLLOWING IS PART OF THE STANDARD CYLINDER & MOUNTING GP-STEERING
136-1711	[4]	PIN AS

		THE FOLLOWING ARE PART OF THE STANDARD COUNTERWEIGHT GP-
103-5796	[1]	PIN-KEEPER
219-0017	[1]	PIN-HITCH

		THE FOLLOWING ARE PART OF THE STANDARD KICKOUT & POSITIONER GP
5V-6439	[2]	PLATE
087-5421	[1]	PLATE

		THE FOLLOWING ARE PART OF THE LINES GP-STEERING
128-1602	[1]	BRACKET AS
128-1605	[1]	TUBE AS
140-3681	[1]	TUBE AS
147-3150	[1]	ANGLE AS
170-9151	[1]	TUBE AS
211-3678	[2]	BRACKET AS

		THE FOLLOWING IS PART OF THE STANDARD HORN GP-ELECTRIC
209-8071	[1]	BRACKET

		THE FOLLOWING ARE PART OF THE STANDARD FILLER GP-POWER TRAIN OIL
131-8031	[1]	TUBE AS
138-5763	[1]	TUBE AS

		THE FOLLOWING ARE PART OF THE STANDARD CONTROL GP-SERVICE BRAKE
5I-3883	[1]	BRACKET AS
6D-8305	[2]	CLAMP
144-4422	[1]	BRACKET AS
144-6694	[1]	BRACKET AS
147-3150	[1]	ANGLE AS
218-2330	[1]	BRACKET AS

		THE FOLLOWING ARE PART OF THE STANDARD BATTERY & WIRING GP
212-3413	[1]	BRACKET AS
212-3415	[1]	BRACKET AS

		THE FOLLOWING IS PART OF THE STANDARD LINES GP-HYDRAULIC
129-4349	[1]	TUBE AS

		THE FOLLOWING ARE PART OF THE STANDARD LINES GP-TORQUE CONVERTER COOLER
190-5489	[1]	TUBE AS
190-7651	[1]	BRACKET AS
191-2449	[2]	PLATE AS
192-9704	[1]	BRACKET AS

		THE FOLLOWING IS PART OF THE STANDARD PUMP & MOUNTING GP-HYDRAULIC FAN
191-3679	[1]	BRACKET AS

		THE FOLLOWING IS PART OF THE STANDARD TANK GP-FUEL
7X-7700	[1]	CAP AS-FUEL TANK (VENTED LOCKING)

		THE FOLLOWING IS PART OF THE STANDARD FUMES DISPOSAL GP
3V-0778	[1]	BRACKET

		THE FOLLOWING ARE PART OF THE STANDARD LINES GP-HYDRAULIC OIL COOLER
8R-9137	[1]	ANGLE
146-3204	[1]	BRACKET
224-6670	[1]	BRACKET

		THE FOLLOWING ARE PART OF THE STANDARD LINES GP-PILOT
8V-8388	[2]	TUBE AS
130-8284	[1]	BRACKET AS
140-0873	[1]	BRACKET AS
148-7221	[1]	BRACKET AS

		THE FOLLOWING IS PART OF THE STANDARD ACTUATOR GP-PARKING BRAKE
126-7730	[1]	BRACKET AS
M		METRIC PART

198-4586: PROTECTION AR-CORROSION

PROTECTION AR-CORROSION

198-4586 PROTECTION AR-CORROSION -CUSTOM
S/N AYL1-UP
HMU/PILOT MODELS
CANNOT BE USED WITH 197-0343 LUBRICATION AR-AUTOMATIC, 192-4676 HYDRAULIC AR-3 VALVE, 226-6501 CONVERSION AR-RIDE CONTROL, 197-0345 LUBRICATION AR-AUTOMATIC, 197-0869 LUBRICATION AR-AUTOMATIC, 197-0346 LUBRICATION AR-AUTOMATIC, 209-2427 LIFT AR-HIGH, 209-2429 LIFT AR-HIGH, 226-3769 CONDENSER & MTG GP-REFRIGERANT, 200-7137 PRECLEANER GP, 188-0098 HYDRAULIC AR-HIGH LIFT, 217-0954 LOGGING AR

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Part No	Qty	Parts name
200-7502 Y	[1]	AIR CONDITIONER AR (WITH ANTI-CORROSION PROTECTION)
198-4588 Y	[1]	ALTERNATOR GP-CHARGING
175-9073	[1]	BAFFLE
196-8719 Y	[1]	CONVERSION GP-MACHINE (CORROSION PROTECTION)
223-6201 Y	[1]	RADIATOR & FAN GP
197-1525 OY	[1]	PROTECTION AR-HARDWARE (LOADER & REAR FRAME)
202-7408 Y	[1]	LINES GP-AIR
229-1941 Y	[1]	LINES GP-HYDRAULIC
199-8518 Y	[1]	LINES GP-SERVICE BRAKE
229-1450 Y	[1]	PANEL & MTG GP-CIRCUIT BREAKER
195-9833 Y	[1]	PIN GP-HOOD (W/LUBRICATION FITTINGS)
197-9986 Y	[1]	PLATE & FILM GP
200-7137 Y	[1]	PRECLEANER GP
230-0867 Y	[1]	STEERING AR-SECONDARY
229-1939 Y	[1]	SWITCH GP-DISCONNECT
229-1940 Y	[1]	TRANSMISSION AR (FREE WHEEL STATOR TORQUE CONV)
229-1974 Y	[1]	CONTROL GP-RIDE
		***STANDARD REMOVAL***
189-6650 L		RADIATOR & FAN GP
190-3776 N	[1]	TRANSMISSION AR (FREE WHEEL STATOR TORQUE CONV)
L		PART OF STANDARD CHASSIS AR
N		PART OF STANDARD POWER TRAIN AR
O		TO PROVIDE STAINLESS STEEL HARDWARE
Y		SEPARATE ILLUSTRATION

224-2989: PROTECTION AR-CORROSION

PROTECTION AR-CORROSION

224-2989 PROTECTION AR-CORROSION -CUSTOM
S/N BAB1-UP; AYL1-UP
PART OF 230-0867 STEERING AR-SECONDARY

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Part No	Qty	Parts name
185-4266	[1]	BRACKET AS
224-2992	[1]	BRACKET AS
223-3267	[1]	PLATE AS
		***ATTACHMENT REMOVAL***
127-9323 J	[1]	BRACKET AS
189-5604 J	[1]	PLATE AS
204-8428 J	[1]	HOSE AS
J		PART OF STANDARD WIRING GP-SECONDARY STEERING

233-7349: PROTECTION AR-CORROSION

PROTECTION AR-CORROSION

233-7349 PROTECTION AR-CORROSION -CUSTOM
S/N BAB1-UP
HMU/PILOT MODELS
CANNOT BE USED WITH 192-4676 HYDRAULIC AR-3 VALVE, 226-6501 CONVERSION AR-RIDE CONTROL, 197-0343 LUBRICATION AR-AUTOMATIC, 197-0345 LUBRICATION AR-AUTOMATIC, 197-0869 LUBRICATION AR-AUTOMATIC, 209-2427 LIFT AR-HIGH, 209-2429 LIFT AR-HIGH

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Part No	Qty	Parts name
200-7502 Y	[1]	AIR CONDITIONER AR (WITH ANTI-CORROSION PROTECTION)
198-4588 Y	[1]	ALTERNATOR GP-CHARGING
175-9073	[1]	BAFFLE
196-8719 Y	[1]	CONVERSION GP-MACHINE (CORROSION PROTECTION)
223-6201 Y	[1]	RADIATOR & FAN GP
197-1525 NY	[1]	PROTECTION AR-HARDWARE (LOADER & REAR FRAME)
202-7408 Y	[1]	LINES GP-AIR
229-1941 Y	[1]	LINES GP-HYDRAULIC
199-8518 Y	[1]	LINES GP-SERVICE BRAKE
229-1450 Y	[1]	PANEL & MTG GP-CIRCUIT BREAKER
195-9833 Y	[1]	PIN GP-HOOD (W/LUBRICATION FITTINGS)
197-9986 Y	[1]	PLATE & FILM GP
200-7137 Y	[1]	PRECLEANER GP
230-0867 Y	[1]	STEERING AR-SECONDARY
229-1939 Y	[1]	SWITCH GP-DISCONNECT
233-7856 Y	[1]	TRANSMISSION AR
229-1974 Y	[1]	CONTROL GP-RIDE
		***STANDARD REMOVAL***
189-6650 J	[1]	RADIATOR & FAN GP
191-2351 L	[1]	TRANSMISSION AR (FREE WHEEL STATOR TORQUE CONV)
J		PART OF STANDARD CHASSIS AR
L		PART OF STANDARD POWER TRAIN AR
N		TO PROVIDE STAINLESS STEEL HARDWARE
Y		SEPARATE ILLUSTRATION

223-6201: RADIATOR & FAN GP

RADIATOR & FAN GP

223-6201 RADIATOR & FAN GP -CUSTOM
S/N BAB1-UP; AYL1-UP
PART OF 198-4586, 233-7349 PROTECTION AR-CORROSION

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3R-8530	[4]	BOSS (31.75MM THK)
2.	4E-1384	[2]	BUMPER-CONICAL
3.	5V-8780	[1]	KNOB
4.	8F-8151	[1]	VALVE-SHUTOFF
5.	8T-2893	[2]	LOCK AS-CYLINDER
			(EACH INCLUDES)
	7F-9223	[1]	LOCKWASHER
	8T-5004	[1]	SCREW-MACHINE (1/4-28X0.375 IN)
6.	9L-8781	[3]	WASHER (0.406X1.5X0.188 IN THK)
7.	121-3307	[2]	MOUNT AS-RUBBER
			(EACH INCLUDES)
	8T-4226	[1]	WASHER-PLATED (10.5X45X3MM THK)
8.	137-4238	[1]	ADAPTER
9.	160-4076	[6]	BOLT
10.	160-4079	[9]	BOLT
11.	164-4413	[3]	MOUNT
12.	186-0116	[1]	SPIDER AS-FAN
13.	186-4718	[15]	WASHER
14.	188-5039	[1]	BAFFLE AS
	174-5807	[7]	RIVET-POP
15.	188-5040	[1]	BAFFLE AS
	174-5807	[6]	RIVET-POP
16.	188-5041	[1]	BAFFLE AS
	174-5807	[6]	RIVET-POP
17.	189-6653	[1]	BRACKET AS
	8T-3490 M	[4]	NUT-WELD (M10X1.5 THD)
	9R-8151	[2]	BLOCK
18.	189-6654	[1]	ANGLE AS
	8T-3490 M	[6]	NUT-WELD (M10X1.5 THD)
19.	189-6656	[1]	SUPPORT AS
	8T-3490 M	[2]	NUT-WELD (M10X1.5 THD)
20.	189-6657	[1]	ANGLE AS
	8T-3490 M	[4]	NUT-WELD (M10X1.5 THD)
21.	189-6658	[1]	SUPPORT AS (LH)
	6V-9632 M	[2]	NUT-WELD (M6X1 THD)
	8T-3490 M	[11]	NUT-WELD (M10X1.5 THD)
	8T-3612 M	[2]	NUT-WELD (M8X1.25 THD)
	192-7979 M	[1]	STUD-WELD
22.	189-6659	[1]	SUPPORT AS (RH)
	6V-9632 M	[2]	NUT-WELD (M6X1 THD)
	8T-3490 M	[13]	NUT-WELD (M10X1.5 THD)
23.	190-1125	[1]	GROMMET
24.	190-5004	[1]	TANK AS-RADIATOR (TRANSMISSION OIL COOLER CORE)
25.	190-5106	[2]	BRACKET AS
26.	191-2943 Y	[1]	MOTOR GP-GEAR (HYDRAULIC FAN)
27.	195-0349	[1]	SHROUD AS
28.	195-1891	[1]	BRACKET AS
29.	199-3755	[1]	HANDLE
30.	201-7944	[1]	BAFFLE AS
	174-5807	[5]	RIVET-POP
31.	201-7947	[1]	BAFFLE
32.	204-7961	[1]	PLATE
33.	204-9877	[2]	BAFFLE
34.	209-5373	[1]	BRACKET AS
	6V-9632 M	[4]	NUT-WELD (M6X1 THD)
	8T-3490 M	[1]	NUT-WELD (M10X1.5 THD)
35.	209-5789	[1]	BRACKET
36.	209-5790	[1]	BRACKET AS
37.	223-4273	[1]	GUARD GP-FAN
	7X-7729	[12]	WASHER (11X25X3MM THK)
	8T-4195 M	[12]	BOLT (M10X1.5X30MM)
	188-3091	[6]	BRACKET AS
	188-3092	[6]	PLATE
	223-4271	[1]	GUARD AS
	8T-3597 M	[10]	NUT-WELD (M12X1.75 THD)
38.	228-1033	[1]	AFTERCOOLER AS
39.	228-1026	[1]	CORE AS-RADIATOR
40.	228-1027	[1]	CORE AS-HYDRAULIC OIL COOLER
41.	228-1028	[1]	CONDENSER AS-REFRIGERANT
42.	228-6908	[2]	COVER AS
43.	228-7207	[2]	PLATE AS
44.	228-7208	[2]	HINGE AS
			(EACH INCLUDES)
	3B-8489	[1]	FITTING-GREASE (1/8-27 THD)
45.	228-7268	[2]	HINGE AS
46.	228-7292	[1]	LATCH AS
47.	5C-7261 M	[2]	NUT (M8X1.25 THD)
48.	5C-9553 M	[4]	BOLT (M6X1X16MM)
49.	5I-3878	[1]	GROMMET
50.	5P-1076	[10]	WASHER-HARD (13.5X30X4MM THK)
51.	6V-5210 M	[4]	SCREW-MACHINE (M4X0.7X10MM)
52.	7X-0515	[1]	WASHER-HARD (17X35X5MM THK)
53.	7X-2553 M	[2]	BOLT (M16X2X40MM)
54.	7X-2554 M	[4]	BOLT (M16X2X70MM)
55.	7X-7729	[70]	WASHER (11X25X3MM THK)
56.	8T-0337 M	[4]	SCREW-MACHINE (M4X0.7X12MM)
57.	8T-4132 M	[1]	NUT (M16X2 THD)
58.	8T-4133 M	[8]	NUT (M10X1.5 THD)
59.	8T-4136 M	[6]	BOLT (M10X1.5X25MM)
60.	8T-4137 M	[10]	BOLT (M10X1.5X20MM)
61.	8T-4139 M	[8]	BOLT (M12X1.75X30MM)
62.	8T-4195 M	[37]	BOLT (M10X1.5X30MM)
63.	8T-4196 M	[7]	BOLT (M10X1.5X35MM)
64.	8T-4226	[2]	WASHER-PLATED (10.5X45X3MM THK)
65.	8T-4956 M	[2]	BOLT (M12X1.75X35MM)
66.	8T-4971 M	[8]	BOLT (M6X1X30MM)
67.	8T-6466 M	[2]	BOLT (M10X1.50X60MM)
68.	9X-8256	[12]	WASHER (6.6X12X2MM THK)
69.	9X-8257	[6]	WASHER (17.5X30X3.5MM THK)
70.	5P-7483 D		SEAL (.9M)
71.	3E-8349 E		SEAL (90CM)
	D		ORDER BY THE METER
	E		ORDER BY THE CENTIMETER
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

202-7408: LINES GP-AIR

LINES GP-AIR

202-7408 LINES GP-AIR -CUSTOM
S/N BAB1-UP; AYL1-UP
PART OF 198-4586, 233-7349 PROTECTION AR-CORROSION

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	161-6874	[4]	WASHER
2.	199-6960	[1]	TUBE
3.	199-6961	[1]	TUBE
4.	202-7849	[4]	NUT
5.	202-9244	[1]	BRACKET AS
6.	202-9245	[1]	BRACKET AS
7.	202-9247	[1]	BRACKET AS
	8T-3490 M	[2]	NUT-WELD (M10X1.5 THD)
8.	203-4526	[2]	U-BOLT
9.	8T-4121	[2]	WASHER-HARD (11X21X2.5MM THK)
10.	8T-4137 M	[2]	BOLT (M10X1.5X20MM)
11.	8T-4185 M	[1]	BOLT (M10X1.5X50MM)
12.	8T-4196 M	[1]	BOLT (M10X1.5X35MM)
			***STANDARD REMOVAL***
	8T-4192 JM	[1]	BOLT (M12X1.75X25MM)
	8T-4195 JM	[1]	BOLT (M10X1.5X30MM)
	190-5339 L	[1]	BRACKET AS
	190-4993 N	[1]	TUBE
	190-4994 N	[1]	TUBE
	J		PART OF STANDARD PUMP & MOUNTING GP-HYDRAULIC FAN
	L		PART OF STANDARD LINES GP-FUEL FILTER
	M		METRIC PART
	N		PART OF STANDARD LINES GP-AIR

200-7137: PRECLEANER GP

PRECLEANER GP

200-7137 PRECLEANER GP
S/N BAB1-UP; AYL1-UP
PART OF 198-4586, 233-7349 PROTECTION AR-CORROSION

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	200-7138	[1]	PRECLEANER AS
			***STANDARD REMOVAL***
	124-3237 J	[1]	PRECLEANER GP
	J		PART OF STANDARD CLEANER GP-AIR

3E-7577: ALTERNATOR GP-CHARGING

ALTERNATOR GP-CHARGING

3E-7577 ALTERNATOR GP-CHARGING
S/N BAB1-UP; AYL1-UP
24 VOLT, 75 AMPERE
PART OF 198-4588 ALTERNATOR GP-CHARGING

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	9S-2011	[1]	SCREW-MACHINE (1/4-20 X .500 IN)
2.	1H-3244	[1]	LOCKWASHER
3.	2K-4821	[1]	LOCKNUT (5/8-18 THD)
4.	7F-7621	[1]	WASHER (0.635X1.25X0.09 IN THK)
5.	9S-2260	[1]	PLATE-COVER
6.	9S-2255	[1]	COVER
7.	9S-2262	[1]	GASKET
8.	9S-2544	[6]	SCREW-HEX HEAD (8-32X11.13MM)
9.	9B-7233	[10]	LOCKWASHER
10.	9S-2437	[5]	SCREW-TAPPING (10-24X19.05MM)
11.	8F-1434	[5]	LOCKWASHER
12.	5P-3418	[1]	BEARING-ROLLER
13.	5P-3419	[1]	RACE-BEARING INNER
14.	9S-2396	[1]	BUSHING-TERMINAL
15.	9S-2393	[3]	DIODE-NEGATIVE
16.	9N-0943	[1]	PLUG-BEARING WELL
17.	9F-2247	[1]	PLUG-PIPE
18.	9S-2292	[1]	HEAT SINK AS
19.	100-6656	[1]	DIODE AS-ALTERNATOR
20.	9S-9830	[4]	SCREW-FORMING (#8-32 X 19.05MM)
21.	8C-9660	[4]	WASHER (4.6X7.9X0.8MM THK)
22.	9S-2300	[4]	INSULATOR
23.	9S-2301	[1]	INSULATION
24.	9S-2248	[1]	COIL & SUPPORT AS
25.	9N-3388	[3]	BOLT (10-24X.75 IN)
26.	3T-6354	[1]	REGULATOR AS (24 VOLT)
27.	7N-9023	[1]	SCREW AS (8-32 X 26.9MM)
28.	6N-1872	[2]	SCREW AS (8-32 X 1.25 IN)
29.	4B-2043	[4]	NUT (8-32 THD)
30.	100-6657	[1]	PLATE-ALTERNATOR
31.	9S-2302	[1]	ROTOR AS
32.	9S-2005	[1]	GROMMET
33.	2L-8075	[3]	TERMINAL
34.	9S-2013	[1]	KIT-RELAY TERMINAL
35.	100-6658	[1]	WIRE AS-ALTERNATOR
36.	9S-2012	[1]	KIT-OUTPUT TERMINAL (ALTERNATOR)
37.	9S-2389	[1]	STUD AS
38.	9L-6770	[1]	CAP
39.	2P-5616	[1]	FRAME-DRIVE END
40.	9S-2390	[1]	RETAINER
41.	9X-2500	[4]	SCREW-HEX FLANGE (10-24 X 38.1MM)
42.	9S-2009	[4]	SCREW-HEAD (10-24 X 3.625 IN)
43.	100-6532	[1]	COLLAR-ALTERNATOR
44.	5P-7807	[1]	BALL BEARING
45.	100-6531	[1]	FAN-ALTERNATOR
46.	9S-3451	[1]	STATOR AS
	9S-2006	[1]	INSULATOR
	9S-2005	[1]	GROMMET
	9S-2014	[3]	CLIP

198-4588: ALTERNATOR GP-CHARGING

ALTERNATOR GP-CHARGING

198-4588 ALTERNATOR GP-CHARGING -CUSTOM
S/N BAB1-UP; AYL1-UP
PART OF 198-4586, 233-7349 PROTECTION AR-CORROSION

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3E-7577 Y	[1]	ALTERNATOR GP-CHARGING
2.	206-6834	[1]	SHIELD AS
3.	222-1808	[1]	BRACKET AS
	8T-3490 M	[1]	NUT-WELD (M10X1.5 THD)
	8T-3597 M	[1]	NUT-WELD (M12X1.75 THD)
4.	225-1929	[1]	HARNESS AS-ENGINE
	102-8802	[2]	KIT-RECEPTACLE (2 PIN)
	102-8803	[1]	KIT-RECEPTACLE (3 PIN)
	102-8805	[1]	KIT-RECEPTACLE (6 PIN)
			(EACH KIT INCLUDES RECEPTACLE AS AND WEDGE)
	7G-7917	[11]	PLUG-SEAL
	7G-7918	[4]	PLUG-SEAL
	8N-1518	[1]	PLUG AS-CONNECTOR (25 PIN)
	8N-1521	[1]	BELL AS-END
	8T-8737	[78]	PLUG-SEAL
	9X-6772	[3]	STRAP-CABLE
	155-2270	[5]	KIT-CONNECTING PLUG (2 PIN)
	155-2274	[1]	KIT-CONNECTING PLUG (6 PIN)
			(EACH KIT INCLUDES PLUG AS AND WEDGE)
	160-7689	[1]	PLUG AS-CONNECTOR (70 PIN)
	159-9322	[1]	SEAL-O-RING
5.	8T-4121	[1]	WASHER-HARD (11X21X2.5MM THK)
6.	8T-6466 M	[1]	BOLT (M10X1.50X60MM)

			***STANDARD REMOVAL***
	185-5294 FJ	[1]	ALTERNATOR GP-CHARGING
	222-4866 FJ	[1]	BRACKET
	216-9825 FJ	[1]	SHIELD AS
	8T-4223 FJ	[1]	WASHER-HARD (13.5X25.5X3MM THK)
	8T-8919 FJ	[1]	BOLT (1/2-13X1.75 IN)
	216-4955 FL	[1]	HARNESS AS-ENGINE
	F		NOT SHOWN
	J		PART OF STANDARD ALTERNATOR GP-CHARGING
	L		PART OF STANDARD WIRING GP-ENGINE
	M		METRIC PART
	R		REMFG PART MAY BE AVAILABLE
	Y		SEPARATE ILLUSTRATION

Information:

MACHINE ARRANGEMENT

MACHINE AR

Truck Engine News

Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Changes to the Way Serial Numbers are Displayed in Truck Engine News {0374, 1000, 7000}
Changes to the Way Serial Numbers are Displayed in Truck Engine News {0374, 1000, 7000}

Engine News

Improved Registration Process for Retrofit Products {1000, 7000}
2011/04/15

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Changes to the Way Serial Numbers are Displayed in Engine News {0374, 1000, 7000}
Changes to the Way Serial Numbers are Displayed in Engine News {0374, 1000, 7000}

Special Instruction

PreDelivery Inspection of Medium Wheel Loaders{7000}
PreDelivery Inspection of Medium Wheel Loaders{7000}

General Welding Procedures {0679, 7000}
General Welding Procedures {0679, 7000}

Smart Access Quarry Package{7000, 7254, 7319}
Smart Access Quarry Package{7000, 7254, 7319}

Storage Procedure for Caterpillar Products {0355, 1000, 7000}
Storage Procedure for Caterpillar Products {0355, 1000, 7000}

Instructions to Register the Retrofit and Submit Service Reporting {1000, 3000, 7000, 7570}
Instructions to Register the Retrofit and Submit Service Reporting {1000, 3000, 7000, 7570}

Installation of G610 Hardware for Cat® Terrain for Motor Graders, Wheel Dozers, and Wheel Loaders {7605}
Installation of G610 Hardware for Cat^® Terrain for Motor Graders, Wheel Dozers, and Wheel Loaders {7605}

Installation Guide for the Tire Monitoring System on Cat® and Non-Cat Equipment {4203, 7490}
Installation Guide for the Tire Monitoring System on Cat^® and Non-Cat Equipment {4203, 7490}

Installation of Remote Disable Module (RDM) Kit on Cat® and Non-Cat Equipment {7606}
Installation of Remote Disable Module (RDM) Kit on Cat^® and Non-Cat Equipment {7606}

Installation Of Operator ID System on Cat® and Non-Cat Products {7600, 7610, 7620}
Installation Of Operator ID System on Cat^® and Non-Cat Products {7600, 7610, 7620}

Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000}
Introduction to Visualization Service Procedure (VSP) {0374, 1000, 7000}

Service Letter-NACD

PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS
PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS

PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS
PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS

Service Letter-Australia

PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS
PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS

PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS
PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS

Service Letter-CFEL

PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS
PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS

PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS
PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS

Service Letter-CSARL

PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS
PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS

PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS
PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS

Service Letter-Americas

PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS
PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS

PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS
PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS

Technical Information Bulletin

A Recommendation for Initial Parts Stock Quantities Will Now Be Included in Service Letters{1000, 7000, 7751, 7752}
A Recommendation for Initial Parts Stock Quantities Will Now Be Included in Service Letters{1000, 7000, 7751, 7752}

Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490}
Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490}

Tool Operating Manual

439-3938, 439-3939, 439-3940, 439-3941, 439-3942, 439-3943 Link Bracket Assemblies {0374, 0599, 0632, 0700, 7000}
439-3938, 439-3939, 439-3940, 439-3941, 439-3942, 439-3943 Link Bracket Assemblies {0374, 0599, 0632, 0700, 7000}

142-6893 Adjustable Lifting Bracket Group{0599, 0629, 0632, 0701, 0717, 1000, 4000, 7000}
142-6893 Adjustable Lifting Bracket Group{0599, 0629, 0632, 0701, 0717, 1000, 4000, 7000}

General Usage for all Shackle Types{0374, 0599, 0629, 0632, 1122, 6459, 7000}
General Usage for all Shackle Types{0374, 0599, 0629, 0632, 1122, 6459, 7000}

Zip-Tie Installation Guide{0374, 0599, 7000}
Zip-Tie Installation Guide{0374, 0599, 7000}

NEHS1259: 469-7632 Swing Gearbox Lifting Tool for 6015-6090 Hydraulic Mining Shovel {0629, 7000}
NEHS1259: 469-7632 Swing Gearbox Lifting Tool for 6015-6090 Hydraulic Mining Shovel {0629, 7000}

M0074040: 509-5085 Lifting Tool Assembly {0374, 0599, 0629, 0632, 3023, 3159, 3160, 5363, 7000}
M0074040: 509-5085 Lifting Tool Assembly {0374, 0599, 0629, 0632, 3023, 3159, 3160, 5363, 7000}

Service Letter-China

PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS
PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS

PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS
PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS

Service Letter-Asia

PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS
PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS

PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS
PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS

Systems Operation

Service Intervals
Air Conditioning and Heating R134a for All Caterpillar Machines

Reuse And Salvage Guidelines

HVOF Identification and Polishing (Superfinishing){0674, 0679, 1000, 7000, 7562}
HVOF Identification and Polishing (Superfinishing){0674, 0679, 1000, 7000, 7562}

Cleaning Components with Carbon Dioxide (CO2) {0680, 1000, 7000}
Cleaning Components with Carbon Dioxide (CO₂) {0680, 1000, 7000}

Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}
Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}

Custom Service Information

Smart Access Quarry Package{7000, 7254, 7319}
Smart Access Quarry Package{7000, 7254, 7319}

Service Letter-APD

PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS
PRODUCT SUPPORT PROGRAM FOR UPDATING PRODUCT LINK PL121 SATELLITE RADIO SOFTWARE ON CERTAIN INTEGRATED TOOLCARRIERS AND WHEEL LOADERS

PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS
PRODUCT SUPPORT PROGRAM FOR REPLACING PRODUCT LINK PL121 SATELLITE RADIOS ON CERTAIN CATERPILLAR PRODUCTS

Technical Analysis

950G Series II Wheel Loader TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}
950G Series II Wheel Loader TA2 Technical Inspection {0372, 1000, 7000, 753T, 7565}

Technical Analysis 1 (TA1) Visual Inspection for Wheel Loaders {0372, 1000, 7000, 753S, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Wheel Loaders {0372, 1000, 7000, 753S, 7565}

Service Magazine

Special Instruction, REHS1332, "Predelivery Inspection of Medium Wheel Loaders" is Available {7000}
2002/10/07

Welding On Fuel And Hydraulic Tanks {0353, 0679, 1273, 5056, 7000}
2005/12/19

Proper Long Term Storage of Caterpillar Products {0355, 1000, 7000}
2009/04/27

Improvements to the Fuel Sender Group {1273, 1408, 6201, 7481, 7857}
2009/07/27

Changes To Caterpillar Incident Reporting Field Use Form And DSN Incident Report Entry Screens {1000, 7000}
2013/04/17

Redesigned Fluid Sampling Valves Are Now Available for All Cat Products {7542}
2011/02/11

Improved Registration Process for Retrofit Products {1000, 3000, 7000, 7570}
2011/02/17

An Improved 5P-8500 Key Is Now Available {1416, 1416, 7000, 7000}
2011/12/01

TA2 (Technical Analysis) Inspections are Now Available on SIS {0372, 1000, 7000, 753T, 7565}
2013/01/10

A New Tool Operating Manual for Proper Zip-Tie Installation Is Now Available for All Caterpillar Products {0374, 0599, 7000}
2015/08/10

Service Magazines, Engine News, and Truck Engine News Articles Moved from Dealer.cat.com to SISweb {0374, 1000, 7000}
2015/09/24

A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}
A New Visualization Service Procedure (VSP) is Now Used for Certain Publications {0374, 1000, 7000}

Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}
Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}

Process to Print Collage Schematics {0374, 1000, 7000}
Process to Print Collage Schematics {0374, 1000, 7000}

Changes to the Way Serial Numbers are Displayed on Service Magazines {0374, 1000, 7000}
Changes to the Way Serial Numbers are Displayed on Service Magazines {0374, 1000, 7000}

New Service Information Content Is Now Available in Channel 1 {0374, 7000}
New Service Information Content Is Now Available in Channel 1 {0374, 7000}

A New Process Is Available to Request Service Animations for Certain Service Information Procedures {1000, 7000}
A New Process Is Available to Request Service Animations for Certain Service Information Procedures {1000, 7000}

Caterpillar Parts SIS Catalog 950G II :

Truck sale:

Caterpillar 950G II
- Wheel Loaders
FINANZAUTO S.A.

79,420

Caterpillar 950G II, Wheel Loaders, Construction
- Wheel Loaders
FINNING CANADA

Caterpillar 950GII
- Wheel Loaders
WESTERN STATES EQUIPMENT

Caterpillar 950G II
- Wheel Loaders
GREGORY POOLE EQUIPMENT CO.

Caterpillar 950GII
- Wheel Loaders
WAGNER EQUIPMENT CO