6Y6767 TIP GP-LONG AN ATTACHMENT 307 EXCAVATOR

Part No	Qty	Parts name




118-1189 Y	[1]	AIR CONDITIONER GP

118-6749 Y	[1]	COMPRESSOR GP

120-7454 Y	[1]	CONDENSER & MOUNTING GP

120-7455 Y	[1]	LINES GP-AIR CONDITIONER
Y		SEPARATE ILLUSTRATION

#SEBP23130322

118-1189: AIR CONDITIONER GP

AIR CONDITIONER GP

1181189 AIR CONDITIONER GP
PART OF 1155755 AIR CONDITIONER AR
AN ATTACHMENT

c684855 SEBP2313

For full view, you need register

Parts for your 307 EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	119-5812	[1]	HOUSING AS-UPPER
2.	119-5813	[1]	HOUSING AS-LOWER
3.	119-5814	[1]	PLATE AS
4.	119-5815	[1]	PLATE AS
5.	119-5816	[1]	PLATE
6.	119-5836	[1]	COIL
7.	119-5821	[1]	PLATE
8.	119-5820	[1]	PLATE
9.	119-5819	[1]	PLATE
10.	3E-5464	[1]	SWITCH AS-THERMOSTAT
11.	119-5823	[1]	COIL
12.	119-5824	[1]	VALVE
13.	100-3143	[2]	PLATE-ORIFICE
14.	112-9565	[1]	MOTOR AS
	3E-3365	[1]	WEDGE
	9G-0398	[1]	KIT-MOTOR BRUSH
	9W-0852	[2]	PIN-CONNECTOR
	102-8802	[1]	KIT-RECEPTACLE
15.	100-3426	[2]	WHEEL-BLOWER
16.	9G-1950	[1]	RESISTOR
17.	120-7448	[1]	FILTER
18.	119-5825	[1]	HARNESS AS
19.	108-8161	[1]	SWITCH AS-ROTARY
20.	118-6743	[1]	CONTROL-CABLE
21.	119-5826	[1]	CABLE-CONTROL
22.	2V-0099	[1]	KNOB
23.	118-6739	[1]	FILM
24.	119-5832	[1]	SEAL
25.	119-5831	[1]	SEAL
26.	119-5833	[1]	SEAL
27.	119-5835	[1]	SEAL
28.	119-5834	[1]	SEAL
29.	4M-6582	[1]	SEAL-O-RING (15.88MM ID)
30.	6V-1668	[2]	WASHER (3MM THK)
31.	8C-4586	[2]	CLAMP-MOTOR
32.	7X-0490 M	[1]	BOLT (M6X1X200MM)
33.	8T-4205	[33]	WASHER-HARD (2MM THK)
34.	119-5837	[1]	SWITCH
35.	9X-8117	[2]	TUBE AS
36.	3T-0851 M	[2]	LOCKNUT (M5X8 THD)
37.	5P-7070	[2]	INSULATION-STRIP
38.	7K-3262	[2]	SCREW
39.	2R-2376	[2]	WASHER (0.8MM THK)
40.	7K-4201	[2]	NUT-SPEED
41.	6V-6718	[6]	SCREW-WASHER HEAD
42.	8L-7905	[4]	RIVET-POP
43.	2P-4339	[3]	NUT-JAM (7/16-20 THD)
44.	5P-8440	[2]	GROMMET
45.	3S-2093	[6]	STRAP-CABLE (1.75IN DIA)
46.	8C-3756	[1]	FILM-IDENTIFICATION
47.	4B-4274	[4]	WASHER (1.2MM THK)
48.	3K-8785	[1]	GROMMET
49.	8T-0288 M	[2]	BOLT (M5X0.8X12MM)
50.	1P-2807	[2]	FILM-SYMBOL (LIFT)
51.	5C-9553 M	[28]	BOLT (M6X1.0X16MM)
52.	9X-2044 M	[18]	SCREW-TRUSS HEAD (M6X1X16MM)
53.	8C-8451 M	[1]	BOLT (M6X1.0X40MM)
54.	099-0492 M	[4]	LOCKNUT (M6X1.0 THD)
	M		METRIC PART

#SEBP23130323

111-7391: CAB GP

CAB GP

1117391 CAB GP
PART OF 1117610 OPERATOR AR

SEBP23130323 SEBP2313

For full view, you need register

Parts for your 307 EXCAVATOR:

CATERPILLAR SIS

Part No	Qty	Parts name




116-7800 Y	[1]	CAP GP

8T-4139	[7]	BOLT

8T-6868	[2]	BOLT

5P-1076	[9]	WASHER-HARD
Y		SEPARATE ILLUSTRATION

#SEBP23130324

116-7800: CAB GP

CAB GP

1167800 CAB GP
S/N 2WM225-UP
PART 1117391 CAB

SEBP23130324 SEBP2313

For full view, you need register

Parts for your 307 EXCAVATOR:

CATERPILLAR SIS

Part No	Qty	Parts name





121-9360 Y	[1]	CAB GP

120-7277 Y	[1]	DOOR GP

121-9358 Y	[1]	WINDSHIELD GP

117-3872 Y	[1]	WIPER GP-UPPER

112-3952	[1]	BONDING SLOW KIT
112-3953	[1]	BONDING SPEEDY
Y		SEPARATE ILLUSTRATION

#SEBP23130325

116-7800: CAB GP

CAB GP

1167800 CAB GP
S/N 2WM1-224
PART OF 1117391 CAB

SEBP23130325 SEBP2313

For full view, you need register

Parts for your 307 EXCAVATOR:

CATERPILLAR SIS

Part No	Qty	Parts name




120-7276 Y	[1]	CAB GP

120-7277 Y	[1]	DOOR GP

120-7279 Y	[1]	WINDSHIELD GP

120-7278 Y	[1]	WIPER GP-UPPER
Y		SEPARATE ILLUSTRATION

#SEBP23130326

120-7276: CAB GP

CAB GP

1207276 CAB GP-PART 1 OF 2
S/N 2WM1-224
REPLACED BY 1219360-PAGE 235.01
PART OF 1167800 CAB

SEBP23130326 SEBP2313

For full view, you need register

Parts for your 307 EXCAVATOR:

CATERPILLAR SIS

Part No	Qty	Parts name



8T-4189	[5]	BOLT (M8X1.25X20MM)
117-5645	[3]	BOLT (M6X1X20MM)
6V-7357	[4]	BOLT (M6X1.0X25MM)
6C-9241	[4]	BOLT
8T-1160	[2]	BOLT-SOCKET HEAD (M10X1.5X50MM)
117-5644	[3]	BOOT
6C-8985	[1]	BOX
5C-8310	[1]	BRACKET-RING
109-5008	[1]	BUMPER-CONICAL
4E-1384	[1]	BUMPER-CONICAL

119-9429	[1]	CAB AS
6C-8996	[8]	CAP
6C-8998	[2]	CAP
6C-9001	[1]	CLAMP
6C-9089	[8]	CAP-NUT
6C-8986	[2]	CLIP-AXLE

6C-8971	[1]	FILM
8T-6842	[1]	FILM-INSTRUCTION
119-9431	[1]	FILTER

6C-8968	[1]	GLASS
119-9436	[1]	GLASS
119-9438	[1]	GLASS-PLASTIC
119-9432	[1]	GLASS-REAR
119-9425	[1]	GUIDE

119-9427	[1]	HANDLE
6C-8997	[1]	HANDLE
120-4758	[1]	HEADLINER
6C-8972	[1]	HOOK

119-9428	[1]	KNOB

8Y-6380	[1]	LATCH AS
119-9424	[1]	LEVER
120-4763	[1]	LINER
120-4754	[1]	LINER-LH
120-4764	[1]	LINER-REAR
120-4757	[1]	LINER-RH
120-4767	[1]	LOCK
095-0827	[6]	LOCKWASHER-TOOTH

5P-6872	[1]	MIRROR

4I-5049	[3]	NUT
5C-7261	[6]	NUT
117-5640	[3]	NUT

119-9437	[1]	PLATE
120-4765	[1]	PLATE AS
120-4766	[1]	PLATE

#SEBP23130327

120-7276: CAB GP

CAB GP

1207276 CAB GP-PART 2 OF 2
S/N 2WM1-224
REPLACED BY 1219360-PAGE 235.01
PART OF 1167800 CAB

SEBP23130327 SEBP2313

For full view, you need register

Parts for your 307 EXCAVATOR:

CATERPILLAR SIS

Part No	Qty	Parts name


6C-9236	[2]	RETAINER
5C-8311	[1]	RING
6C-9237	[2]	RIVER
119-9423	[1]	ROD

6C-9131	[2]	SCREW
3C-1878	[3]	SCREW-MACHINE
119-9439	[1]	SEAL
120-4768	[1]	SEAL
6C-4000	[4]	SHIM (1MM THK)
119-9426	[1]	STRIKER
119-9434	[1]	STOP SEAL
6C-9000	[1]	SUPPORT

5V-5521	[4]	WASHER-SEAL
6C-9087	[11]	WASHER (LOCKWASHER)
6C-9130	[14]	WASHER
9X-8256	[4]	WASHER (2MM THK)
109-1267	[4]	WASHER

#SEBP23130328

121-9360: CAB GP

CAB GP

1219360 CAB GP
S/N 2WM225-UP
PART OF 1167800 CAB

c622292 SEBP2313

For full view, you need register

Parts for your 307 EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	6C-9224	[8]	SCREW
2.	6C-8972	[1]	HOOK
3.	6C-9131	[2]	SCREW
4.	119-9431	[1]	FILTER
5.	119-9432	[1]	GLASS-REAR
6.	119-9433	[1]	SEAL
7.	119-9434	[1]	SEAL
8.	5C-8310	[1]	BRACKET-RING
9.	5C-8311	[1]	RING
10.	119-9436	[1]	GLASS
11.	6C-9237	[2]	RIVET
12.	6C-9236	[2]	RETAINER
13.	119-9437	[1]	PLATE
14.	3C-1878 M	[3]	SCREW-MACHINE
15.	124-5677	[1]	GLASS
16.	6C-9089	[3]	NUT-CAP
17.	117-5640 M	[3]	NUT
18.	095-0827	[6]	LOCKWASHER-TOOTH
19.	6C-9130	[9]	WASHER
20.	4I-5049	[3]	NUT
21.	117-5645 M	[3]	BOLT
22.	117-5644	[2]	BOOT
23.	114-5329	[1]	GLASS
24.	119-9439	[1]	SEAL
25.	6C-8971	[1]	FILM
26.	120-4754	[1]	LINER-LH
27.	120-4757	[1]	LINER-RH
28.	120-4758	[1]	HEADLINER
29.	120-4763	[1]	LINER
30.	120-4764	[1]	LINER-REAR
31.	120-4765	[1]	PLATE AS
32.	120-4766	[1]	PLATE
33.	120-4767	[1]	LOCK
34.	5J-5003	[2]	PLUG
35.	8T-4189 M	[5]	BOLT (M8X1.25X20MM)
36.	8T-4224	[2]	WASHER-HARD
37.	6C-8996	[8]	CAP
38.	6C-8980	[4]	NOZZLE-AIR
39.	9X-2044 M	[5]	SCREW-TRUSS HEAD
40.	123-5047	[1]	SEAL
41.	6V-7357 M	[4]	BOLT (M6X1.0X25MM)
42.	9X-8256	[4]	WASHER (2MM THK)
43.	8Y-6380	[1]	LATCH AS
44.	6C-8985	[1]	BOX
45.	6C-9087	[7]	WASHER
46.	109-5008	[1]	BUMPER-CONICAL
47.	4E-1384	[1]	BUMPER-CONICAL
48.	6C-4000	[4]	SHIM (1MM THK)
49.	6C-8997	[1]	HANDLE
50.	6C-9000	[1]	SUPPORT
51.	5P-6872	[1]	MIRROR
52.	8T-1160 M	[2]	BOLT-SOCKET HEAD (M10X1.5X50 MM)
53.	6C-9001	[1]	CLAMP
54.	6C-8998	[2]	CAP
55.	109-1267	[4]	WASHER
56.	5C-7261 M	[6]	NUT (M8X1.25 THD)
57.	6C-8986	[2]	CLIP-AXLE
58.	119-9423	[1]	ROD
59.	119-9424	[1]	LEVER
60.	119-9425	[1]	GUIDE
61.	119-8338	[2]	SCREW
62.	6C-9048	[1]	NUT
63.	119-8339	[1]	SPRING
64.	8T-4200 M	[3]	BOLT (M8X1.25X16MM)
65.	7X-2552 M	[2]	BOLT (M16X2.0X30MM)
66.	090-8865	[2]	SPACER
67.	119-8340	[2]	SEAL
68.	119-9426	[1]	STRIKER
69.	8T-4133 M	[2]	NUT (M10X1.50 THD)
70.	7X-7729	[2]	WASHER (3MM THK)
71.	8T-4121	[2]	WASHER (2.5MM THK)
72.	8T-6842	[1]	FILM-INSTRUCTION
73.	6C-9241	[8]	BOLT
74.	5V-5521	[8]	WASHER-SEAL
75.	119-8341	[1]	SEAL
76.	119-8342	[1]	SEAL
77.	119-9427	[1]	HANDLE
78.	119-9428	[1]	KNOB
79.	6C-9235	[1]	IDENTIFICATION
80.	6C-9058	[1]	SCREW
81.	6C-9092	[4]	WASHER
82.	119-8343	[2]	COVER
	M		METRIC PART

#SEBP23130329

118-6749: COMPRESSOR GP

COMPRESSOR GP

1186749 COMPRESSOR GP
1011759-PAGE 235.05
PART OF 1155755 AIR CONDITIONER AR
AN ATTACHMENT

c622973 SEBP2313

For full view, you need register

Parts for your 307 EXCAVATOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	101-1759 Y	[1]	COMPRESSOR GP-CLUTCH & REFRIG
2.	8T-4154 M	[1]	BOLT
3.	5C-7261 M	[1]	NUT (M8X1.25 THD)
4.	8T-4224	[2]	WASHER-HARD (2MM THK)
5.	116-2405	[1]	PULLEY-CRANKSHAFT
6.	8T-4182 M	[4]	BOLT (M10X1.5X45MM)
7.	8T-4121	[8]	WASHER (2.5MM THK)
8.	8T-5436 M	[1]	BOLT (M10X1.50X130MM)
9.	6V-7744 M	[1]	LOCKNUT (M10X1.50 THD)
10.	118-6747	[1]	BRACKET
11.	8T-4136 M	[2]	BOLT (M10X1.50X25MM)
12.	118-6748	[1]	PLATE
13.	061-7139	[1]	V-BELT
14.	122-0642	[1]	GUARD-FAN
15.	8T-4908 M	[1]	BOLT (M8X1.25X25MM)
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

Information:

WORK TOOLS

GROUND ENGAGING TOOLS (G.E.T.)

Special Instruction

Procedure To Install Wear Protection On Base Edges And Adapters{6800}
Procedure To Install Wear Protection On Base Edges And Adapters{6800}

Recommendations for Welding J-Series 2-Strap Bucket Adapters to Base Edges{6800, 6801, 6803}
Recommendations for Welding J-Series 2-Strap Bucket Adapters to Base Edges{6800, 6801, 6803}

Installation and Removal Of The Mechanically Attached Wear Plate System
Installation and Removal Of The Mechanically Attached Wear Plate System

Converting Excavator Buckets from J-Series Base Edge Assemblies to the K-Series{6523, 6800, 6803, 6823}
Converting Excavator Buckets from J-Series Base Edge Assemblies to the K-Series{6523, 6800, 6803, 6823}

Convert the Buckets from the J-Series Base Edge Assemblies to the K-Series Base Edge Assemblies{6523, 6803, 6805}
Convert the Buckets from the J-Series Base Edge Assemblies to the K-Series Base Edge Assemblies{6523, 6803, 6805}

398-6784 Recommended J Series Two Strap Adapter Welding Sequence {0679, 6800, 6801, 6802, 6803, 6805}
398-6784 Recommended J Series Two Strap Adapter Welding Sequence {0679, 6800, 6801, 6802, 6803, 6805}

398-6786 Recommended J Series Flush Mount/Abrasion Adapter Welding Sequence {0679, 6800, 6801, 6802, 6803, 6805}
398-6786 Recommended J Series Flush Mount/Abrasion Adapter Welding Sequence {0679, 6800, 6801, 6802, 6803, 6805}

256-2928 Recommended K Series Two Strap Adapter Welding Sequence {0679, 6800, 6801, 6802, 6803, 6805}
256-2928 Recommended K Series Two Strap Adapter Welding Sequence {0679, 6800, 6801, 6802, 6803, 6805}

256-2930 Recommended K Series Flush Mount/Abrasion Adapter Welding Sequence{0679, 6800, 6801, 6802, 6803, 6805}
256-2930 Recommended K Series Flush Mount/Abrasion Adapter Welding Sequence{0679, 6800, 6801, 6802, 6803, 6805}

Loader and Excavator Bucket Base Edge Assembly Welding Requirements {0679, 6001, 6101, 6102, 6103, 6104, 6110, 6112, 6120, 6122, 6138, 6503, 6523, 6530, 6800, 6801, 6823}
Loader and Excavator Bucket Base Edge Assembly Welding Requirements {0679, 6001, 6101, 6102, 6103, 6104, 6110, 6112, 6120, 6122, 6138, 6503, 6523, 6530, 6800, 6801, 6823}

Repairing Small Cracks In Base Edge Assemblies{0679, 6001, 6120, 6801}
Repairing Small Cracks In Base Edge Assemblies{0679, 6001, 6120, 6801}

Procedure for Installation and Removal of Cat<SUP>®</SUP> Advansys Tips {0751, 6001, 6800, 6805}
Procedure for Installation and Removal of Cat^® Advansys Tips {0751, 6001, 6800, 6805}

Instructions for Welding the Cat<SUP>®</SUP> Advansys™ Adapters on Excavator and Wheel Loader Buckets {0679, 6001, 6800}
Instructions for Welding the Cat^® Advansys™ Adapters on Excavator and Wheel Loader Buckets {0679, 6001, 6800}

Tool Operating Manual

Using the 149-0173 Choker-Style Fabric Basket to Install and Remove Bucket Teeth{0374, 0599, 0751, 6700, 6800}
Using the 149-0173 Choker-Style Fabric Basket to Install and Remove Bucket Teeth{0374, 0599, 0751, 6700, 6800}

Using 149-0174 Non-Choker Style Fabric Baskets to Install or Remove Bucket or Blade Cutting Edges{0374, 0599, 0632, 0700, 0751, 6800}
Using 149-0174 Non-Choker Style Fabric Baskets to Install or Remove Bucket or Blade Cutting Edges{0374, 0599, 0632, 0700, 0751, 6800}

Reuse And Salvage Guidelines

Application of Abrasion Resistant Material{0374, 0679, 0751, 0759, 6800}
Application of Abrasion Resistant Material{0374, 0679, 0751, 0759, 6800}

Service Magazine

The Special Instruction, REHS0597, "Recommendation for Welding 2-Strap Bucket Adapters to Base Edges" is Available {6800, 6801, 6803}
2001/04/23

Pin Remover Helps the Technician Change K Series Bucket Teeth {0751}
2004/02/16

Correct Installation and Removal of Retainers for K Series Bucket Tips {6800, 6803, 6805}
2006/02/06

The Special Instruction, REHS2834 , "Converting Straight Edge Buckets from the J-Series Base Edge Assemblies to the K-Series" Is Now Available. {6523, 6800, 6803, 6823}
2005/12/05

Preferred Positions for Mechanically Attached Wear Plates (MAWPS) {6100, 6120, 6820}
2009/04/27

Caterpillar Parts SIS Catalog 307 :

102-3137 STICK GP-HOE

102-3136 STICK GP-HOE

102-5293 STICK AR-HOE

102-5294 STICK AR-HOE

112-4843 PLATE GP-HAMMER

116-2648 PLATE GP-HAMMER

108-9421 PLATE GP-HAMMER

107-9942 LINKAGE GP-BUCKET

115-5755 AIR CONDITIONER AR

118-1189 AIR CONDITIONER GP