190-5096 WIRING GP-CHASSIS S/N AYL1198-UP PART OF 217-0912 ELECTRICAL AR Type 2 950G II WHEEL LOADER

ELECTRICAL AND STARTING SYSTEM

WIRING GP

0. 190-5096 WIRING GP-
1. 191-6802 WIRING GP-
2. 209-0767 WIRING GP-
3. 190-5038 WIRING GP-
4. 190-5092 WIRING GP-
5. 217-0771 WIRING GP-
6. 217-0771 WIRING GP-

STARTING AID GP

7. 258-7610 WIRING GP-

WIRING GP

8. 190-5087 WIRING GP-
9. 190-5087 WIRING GP-
0. INFORMATION

WHEEL LOADER 950G II WHEEL LOADER AYL
950G II Wheel Loader AYL00001-UP (MACHINE) POWERED BY 3126 Engine SEBP3280 950G II AYL (1999)

ELECTRICAL AND STARTING SYSTEM

WIRING GP

190-5096 WIRING GP-CHASSIS

191-6802 WIRING GP-ELECTRIC CLUTCH

209-0767 WIRING GP-ELECTROHYDRAULIC

190-5038 WIRING GP-ENGINE

#SEBP32800340

190-5096: WIRING GP-CHASSIS

WIRING GP-CHASSIS

190-5096 WIRING GP-CHASSIS
S/N AYL1198-UP
PART OF 217-0912 ELECTRICAL AR
Type 2

i02088118 SEBP3280

For full view, you need register

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3E-5169	[1]	GUARD-SWITCH
2.	3S-2093	[15]	STRAP-CABLE
3.	3D-9872	[2]	PLUG-BUTTON
4.	7K-1181	[4]	STRAP-CABLE
5.	134-2252 Y	[1]	SENSOR GP-TEMPERATURE (8-VOLT)(HYDRAULIC OIL)
6.	172-8660 Y	[1]	SWITCH GP-LIQUID LEVEL (HYDRAULIC OIL)
7.	131-0359	[1]	PLATE-IDENTIFICATION (ENGINE STOP, RUN)
8.	136-3937	[1]	SHEET
9.	136-4129	[1]	BRACKET
10.	146-0240	[1]	SWITCH GP-TOGGLE (LOCKING)(HOOD TILT ACTUATOR)
	3E-3371	[1]	WEDGE-RECEPTACLE LOCK (3-PIN)
	6T-3631	[2]	NUT-HEX (15/32-32-THD)
	6T-3632	[1]	LOCKWASHER
	6T-3633	[1]	RING-LOCKING
	8T-8729	[3]	PIN-CONNECTOR (16-GA TO 18-GA)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
11.	158-6634	[1]	SWITCH GP-TOGGLE (GROUND LEVEL SHUTDOWN)
	3E-3377	[1]	WEDGE-RECEPTACLE LOCK (4-PIN)
	6T-3631	[2]	NUT-HEX (15/32-32-THD)
	6T-3632	[1]	LOCKWASHER
	6T-3633	[1]	RING-LOCKING
	8T-8729	[3]	PIN-CONNECTOR (16-GA TO 18-GA)
	102-8804	[1]	KIT-RECEPTACLE (4-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
12.	174-4312	[1]	SWITCH AS-PRESSURE (PARKING BRAKE OIL)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	3E-3371	[1]	WEDGE-RECEPTACLE LOCK (3-PIN)
	8T-8729	[3]	PIN-CONNECTOR (16-GA TO 18-GA)
13.	175-3244	[1]	SWITCH AS-PRESSURE (SERVICE BRAKE OIL)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	3E-3371	[1]	WEDGE-RECEPTACLE LOCK (3-PIN)
	8T-8729	[3]	PIN-CONNECTOR (16-GA TO 18-GA)
14.	188-6185	[2]	GROMMET
15.	188-6252	[1]	FILM-INSTRUCTION (HOOD TILT)
16.	190-5098 Y	[1]	PANEL GP-CIRCUIT BREAKER
17.	241-7878 C	[1]	HARNESS AS-CHASSIS (MAIN)
	102-8802	[6]	KIT-RECEPTACLE (2-PIN)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
	102-8804	[1]	KIT-RECEPTACLE (4-PIN)
	102-8801	[2]	KIT-RECEPTACLE (12-PIN)
			(EACH KIT-RECEPTACLE INCLUDES RECEPTACLE AS & WEDGE)
	7G-7917	[11]	PLUG-SEAL
	7G-7918	[4]	PLUG-SEAL
	7G-7919	[2]	PLUG-SEAL
	129-7164	[1]	RECEPTACLE AS-CONNECTOR (1-PIN)
	155-2252	[1]	PLUG AS-CONNECTOR (12-PIN)
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
	155-2274	[1]	KIT-CONNECTING PLUG (6-PIN)
			(EACH KIT-CONNECTING PLUG INCLUDES PLUG AS & WEDGE)
	8N-1517	[1]	RECEPTACLE AS-CONNECTOR (25-PIN)
	8N-1521	[1]	BELL AS-END
	129-7163	[1]	PLUG AS-CONNECTOR (1-PIN)
18.	209-8699	[1]	HARNESS AS-CHASSIS (HYDRAULIC TANK)
	8T-8737	[7]	PLUG-SEAL
	155-2255	[1]	KIT-CONNECTING PLUG (12-PIN)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
	155-2260	[1]	KIT-CONNECTING PLUG (3-PIN)
			(EACH KIT-CONNECTING PLUG INCLUDES PLUG AS & WEDGE)
19.	033-8248	[1]	CLIP (LOOP)
20.	130-5300	[13]	CLIP
21.	164-4227	[1]	CLIP
22.	5F-9757	[1]	GROMMET
23.	1S-0994	[3]	CLIP (LOOP)
24.	2M-3433	[2]	GROMMET
25.	2M-9780	[1]	SEAL-O-RING
26.	3J-1907	[3]	SEAL-O-RING
27.	4D-7388	[1]	CLIP (LOOP)
28.	4K-8864	[2]	CLIP (LOOP)
29.	4P-7581	[1]	CLIP (LADDER)
30.	4P-8134	[1]	CLIP (LADDER)
31.	4S-1962	[2]	CLIP (LOOP)
32.	4S-4455	[1]	CLIP
33.	5C-8312 M	[4]	NUT (M4X0.7-THD)
34.	6D-4244	[8]	CLIP (LOOP)
35.	6D-4246	[3]	CLIP (LOOP)
36.	6V-1889	[4]	CLIP (LOOP)
37.	7D-7233	[1]	CLIP (LOOP)
38.	8C-9660	[8]	WASHER (4.6X7.9X0.8-MM THK)
39.	8T-4121	[42]	WASHER-HARD (11X21X2.5-MM THK)
40.	8T-4133 M	[8]	NUT (M10X1.5-THD)
41.	8T-4136 M	[3]	BOLT (M10X1.5X25-MM)
42.	8T-4137 M	[28]	BOLT (M10X1.5X20-MM)
43.	8T-4186 M	[3]	BOLT (M10X1.5X40-MM)
44.	8T-4223	[1]	WASHER-HARD (13.5X25.5X3-MM THK)
45.	8T-4244 M	[1]	NUT (M12X1.75-THD)
46.	8T-9405 M	[4]	BOLT-SOCKET HEAD (M4X0.7X16-MM)
47.	9M-8406	[2]	CLIP (LOOP)
48.	8M-2770	[3]	CLIP (LOOP)
49.	2A-2677	[1]	SPACER (10.7X17.14X19.05-MM THK)
50.	4D-7794	[1]	CLIP
51.	4H-1225	[3]	WASHER (11X22X6-MM THK)
52.	132-5789	[1]	CLIP (LADDER)
53.	7N-3718	[2]	CLIP
54.	218-4935	[1]	SUPPRESSOR-ARC
	C		CHANGE FROM PREVIOUS TYPE
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP32800341

191-6802: WIRING GP-ELECTRIC CLUTCH

WIRING GP-ELECTRIC CLUTCH

191-6802 WIRING GP-ELECTRIC CLUTCH -AXLE OIL COOLER PUMP
S/N AYL1-UP
PART OF 191-3314 COOLER & MTG AR-AXLE OIL

i01481349 SEBP3280

1916802 WIRING GP-ELECTRIC CLUTCH Parts scheme

For full view, you need register

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[2]	STRAP-CABLE
2.	155-8998	[1]	SWITCH AS-TEMPERATURE (AXLE OIL COOLER)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
	3E-3365	[1]	WEDGE-RECEPTACLE LOCK (2-PIN)
	8T-8729	[2]	PIN-CONNECTOR (16-GA TO 18-GA)
3.	224-8889	[1]	HARNESS AS-SENSOR (COOLER PUMP CLUTCH SWITCH)
	155-2269	[1]	PLUG AS-CONNECTOR (2-PIN)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
4.	224-8888	[1]	HARNESS AS-CONTROL (COOLER PUMP CLUTCH)
	155-2269	[1]	PLUG AS-CONNECTOR (2-PIN)
			(INCLUDES PLUG AS & WEDGE)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
5.	130-5300	[1]	CLIP
6.	4D-7794	[1]	CLIP
8.	8T-4121	[2]	WASHER-HARD (11X21X2.5-MM THK)
10.	8T-4136 M	[1]	BOLT (M10X1.5X25-MM)
11.	8T-4195 M	[1]	BOLT (M10X1.5X30-MM)
	M		METRIC PART

#SEBP32800342

209-0767: WIRING GP-ELECTROHYDRAULIC

WIRING GP-ELECTROHYDRAULIC

209-0767 WIRING GP-ELECTROHYDRAULIC
S/N AYL1-UP
PART OF 208-0834, 208-0835, 208-0836 VALVE & MTG GP-MAIN CONTROL

i01912745 SEBP3280

2090767 WIRING GP-ELECTROHYDRAULIC Parts scheme

For full view, you need register

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[13]	STRAP-CABLE
2.	091-9035	[1]	SPACER (11X25X20-MM THK)
3.	224-5873	[1]	HARNESS AS-VALVE (OIL MANIFOLD, E/H CONTROL)
	102-8802	[3]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE & WEDGE)
	155-2255	[1]	KIT-CONNECTING PLUG (12-PIN)
			(INCLUDES RECEPTACLE & WEDGE)
	155-2270	[8]	KIT-CONNECTING PLUG (2-PIN)
			(INCLUDES RECEPTACLE & WEDGE)
4.	4S-1936	[2]	CLIP
5.	8M-2770	[2]	CLIP (LOOP)
6.	8T-4121	[2]	WASHER-HARD (11X21X2.5-MM THK)
7.	8T-4136 M	[1]	BOLT (M10X1.5X25-MM)
8.	8T-4182 M	[1]	BOLT (M10X1.5X45-MM)
	M		METRIC PART

#SEBP32800343

190-5038: WIRING GP-ENGINE

WIRING GP-ENGINE

190-5038 WIRING GP-ENGINE
S/N TX61-UP; BMA1-UP; 5GG9359-UP
HIGH SIDE ACTIVATION OF AIR INLET HEATER RELAY
PART OF 172-4038, 216-0848, 276-7025 ENGINE AR-COMPLETE

i01488493 SEBP3280

For full view, you need register

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[14]	STRAP-CABLE
2.	105-1797	[6]	MOUNT
3.	153-8920	[1]	HARNESS AS-ENGINE (UNIT INJECTOR)
	6N-7523	[1]	WASHER (6.48X11.9X1.57-MM THK)
	9X-3402	[12]	SOCKET-CONNECTOR (16-GA TO 18-GA)
			-OR-
	126-1768	[12]	SOCKET-CONNECTOR (14-GA TO 16-GA)
	135-5975	[1]	GROMMET-WIRING
	155-2255	[1]	KIT-CONNECTING PLUG (12-PIN)
			(INCLUDES PLUG AS, INTERFACE SEAL & WEDGE)
4.	156-6175	[2]	CLIP (LADDER)
5.	195-7336 Y	[1]	HARNESS AS-ENGINE (ELECTRONIC CONTROL)
6.	8T-4191 M	[1]	BOLT (M10X1.5X16-MM)
7.	113-8690	[1]	WASHER (11.1X37.9X3.3-MM THK)
8.	7X-7729	[1]	WASHER (11X25X3-MM THK)
9.	6V-5217 M	[1]	BOLT (M8X1.25X20-MM)
10.	5P-4116	[1]	WASHER-HARD (8.8X20.5X2-MM THK)
11.	156-9890	[1]	WASHER (9X30X4-MM THK)
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP32800344

190-5092: WIRING GP-ENGINE

WIRING GP-ENGINE

190-5092 WIRING GP-ENGINE
S/N AYL1-453
PART OF 186-3533 ELECTRICAL AR

i01477620 SEBP3280

For full view, you need register

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[2]	STRAP-CABLE
2.	7K-1181	[5]	STRAP-CABLE
3.	116-4491	[1]	BRACKET AS
4.	118-6878	[1]	BRACKET AS
			(EACH BRACKET AS INCLUDES)
	8T-3490 M	[1]	NUT-WELD (M10X1.5-THD)
5.	130-9811	[1]	SENSOR GP-TEMPERATURE (TORQUE CONVERTER OIL)
5A.	130-9811	[1]	SENSOR GP-TEMPERATURE (TRANSMISSION LUBRICATION OIL)
6.	130-9927	[1]	STRIP AS
	8T-3490 M	[1]	NUT-WELD (M10X1.5-THD)
7.	210-1415	[1]	HARNESS AS-ENGINE
	102-8802	[2]	KIT-RECEPTACLE (2-PIN)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
8.	124-3019	[1]	BRACKET AS
	8T-3490 M	[1]	NUT-WELD (M10X1.5-THD)
9.	130-5300	[3]	CLIP
10.	156-6175	[2]	CLIP (LADDER)
11.	194-6722 Y	[1]	SENSOR GP-PRESSURE (TURBOCHARGER INLET)
12.	195-0882	[1]	BRACKET AS
13.	1K-3113	[1]	SPACER (0.546X0.840X3.875-IN THK)
14.	1S-0994	[1]	CLIP (LOOP)
15.	3J-1907	[1]	SEAL-O-RING
16.	3K-0360	[2]	SEAL-O-RING
17.	4D-7794	[2]	CLIP
18.	8T-4189 M	[1]	BOLT (M8X1.25X20-MM)
19.	8M-2770	[1]	CLIP (LOOP)
20.	5C-7261 M	[3]	NUT (M8X1.25-THD)
21.	5P-4116	[8]	WASHER-HARD (8.8X20.5X2-MM THK)
22.	5P-4295	[1]	CLIP
23.	5P-9085	[1]	CLIP (LOOP)
24.	6D-4244	[2]	CLIP (LOOP)
25.	6D-4246	[6]	CLIP (LOOP)
26.	6D-4636	[2]	CLIP (LOOP)
27.	5C-2890 M	[2]	NUT (M6X1-THD)
29.	8T-4121	[7]	WASHER-HARD (11X21X2.5-MM THK)
30.	8T-4122	[1]	WASHER-HARD (17X32X3.5-MM THK)
31.	8T-4136 M	[1]	BOLT (M10X1.5X25-MM)
32.	8T-4137 M	[6]	BOLT (M10X1.5X20-MM)
33.	8T-4190 M	[1]	BOLT (M16X2X25-MM)
34.	8T-4200 M	[1]	BOLT (M8X1.25X16-MM)
35.	8T-4223	[1]	WASHER-HARD (13.5X25.5X3-MM THK)
36.	8T-5041 M	[1]	BOLT (M12X1.75X120-MM)
37.	9M-8406	[3]	CLIP (LOOP)
38.	9X-8256	[2]	WASHER (6.6X12X2-MM THK)
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP32800345

217-0771: WIRING GP-ENGINE

WIRING GP-ENGINE

217-0771 WIRING GP-ENGINE
S/N AYL454-1119
PART OF 217-0912 ELECTRICAL AR

i01853089 SEBP3280

For full view, you need register

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[2]	STRAP-CABLE
2.	7K-1181	[6]	STRAP-CABLE
3.	116-4491	[1]	BRACKET AS
	8T-3490 M	[1]	NUT-WELD (M10X1.5-THD)
4.	118-6878	[1]	BRACKET AS
	8T-3490 M	[1]	NUT-WELD (M10X1.5-THD)
5.	130-9811	[1]	SENSOR GP-TEMPERATURE (TRANSMISSION LUBE OIL)
			(EACH SENDER INCLUDES)
	6V-4589	[1]	SEAL-O-RING
	180-4149	[1]	RETAINER
6.	130-9927	[1]	STRIP AS
	8T-3490 M	[1]	NUT-WELD (M10X1.5-THD)
7.	145-7028	[1]	SENSOR GP-TEMPERATURE (TORQUE CONVERTER OIL)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE & WEDGE)
	3E-3365	[1]	WEDGE-RECEPTACLE LOCK (2-PIN)
8.	164-3652	[1]	ADAPTER
9.	216-4955	[1]	HARNESS AS-ENGINE
	102-8802	[2]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE & WEDGE)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE & WEDGE)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
			(INCLUDES RECEPTACLE & WEDGE)
	155-2270	[5]	KIT-CONNECTING PLUG (2-PIN)
			(INCLUDES PLUG & WEDGE)
	155-2274	[1]	KIT-CONNECTING PLUG (6-PIN)
			(INCLUDES PLUG & WEDGE)
	8N-1518	[1]	PLUG AS-CONNECTOR (25-PIN)
	160-7689	[1]	PLUG AS-CONNECTOR (70-PIN)
	7G-7917	[11]	PLUG-SEAL
	7G-7918	[4]	PLUG-SEAL
	8T-8737	[74]	PLUG-SEAL
10.	130-5300	[4]	CLIP
11.	156-6175	[2]	CLIP (LADDER)
12.	194-6722 Y	[1]	SENSOR GP-PRESSURE (ATMOSPHERIC AIR)
13.	195-0882	[1]	BRACKET AS
	8T-3490 M	[1]	NUT-WELD (M10X1.5-THD)
14.	1K-3113	[1]	SPACER (0.546X0.840X3.875-IN THK)
15.	1S-0994	[1]	CLIP (LOOP)
16.	3J-1907	[1]	SEAL-O-RING
17.	3K-0360	[2]	SEAL-O-RING
18.	4D-7794	[1]	CLIP
19.	5C-2890 M	[2]	NUT (M6X1-THD)
20.	5C-7261 M	[3]	NUT (M8X1.25-THD)
21.	5P-4116	[8]	WASHER-HARD (8.8X20.5X2-MM THK)
22.	5P-4295	[1]	CLIP
23.	5P-9085	[2]	CLIP (LOOP)
24.	6D-4244	[2]	CLIP (LOOP)
25.	6D-4246	[7]	CLIP (LOOP)
26.	6D-4636	[1]	CLIP (LOOP)
27.	7J-0204	[1]	SEAL-O-RING
28.	8M-2770	[1]	CLIP (LOOP)
29.	8T-4121	[8]	WASHER-HARD (11X21X2.5-MM THK)
30.	8T-4122	[1]	WASHER-HARD (17X32X3.5-MM THK)
31.	8T-4136 M	[2]	BOLT (M10X1.5X25-MM)
32.	8T-4137 M	[6]	BOLT (M10X1.5X20-MM)
33.	8T-4189 M	[1]	BOLT (M8X1.25X20-MM)
34.	8T-4190 M	[1]	BOLT (M16X2X25-MM)
35.	8T-4200 M	[1]	BOLT (M8X1.25X16-MM)
36.	8T-4223	[1]	WASHER-HARD (13.5X25.5X3-MM THK)
37.	8T-5001 M	[1]	BOLT (M12X1.75X130-MM)
38.	9M-8406	[3]	CLIP (LOOP)
39.	9X-8256	[2]	WASHER (6.6X12X2-MM THK)
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP32800346

217-0771: WIRING GP-ENGINE

WIRING GP-ENGINE

217-0771 WIRING GP-ENGINE
S/N AYL1120-UP
PART OF 217-0912 ELECTRICAL AR

i01963945 SEBP3280

For full view, you need register

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[2]	STRAP-CABLE
2.	7K-1181	[6]	STRAP-CABLE
3.	116-4491	[1]	BRACKET AS
	8T-3490 M	[1]	NUT-WELD (M10X1.5-THD)
4.	118-6878	[1]	BRACKET AS
5.	264-4297	[1]	SENSOR AS-TEMPERATURE (2-PIN)(TRANSMISSION LUBE OIL)
	137-6645	[1]	PAD-CONNECTOR
6.	127-4667	[1]	STRIP AS
	8T-3490 M	[1]	NUT-WELD (M10X1.5-THD)
7.	145-7028 Y	[1]	SENSOR GP-TEMPERATURE (TORQUE CONVERTER OIL)
8.	164-3652	[1]	ADAPTER
9.	235-0576 C	[1]	HARNESS AS-ENGINE
	102-8802	[2]	KIT-RECEPTACLE (2-PIN)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
			(EACH KIT RECEPTACLE INCLUDES RECEPTACLE AS & WEDGE)
	155-2270	[5]	KIT-CONNECTING PLUG (2-PIN)
	155-2274	[1]	KIT-CONNECTING PLUG (6-PIN)
			(EACH KIT PLUG INCLUDES PLUG AS & WEDGE)
	8N-1518	[1]	PLUG AS-CONNECTOR (25-PIN)
	160-7689	[1]	PLUG AS-CONNECTOR (70-PIN)
10.	130-5300	[4]	CLIP
11.	156-6175	[2]	CLIP (LADDER)
12.	194-6722 Y	[1]	SENSOR GP-PRESSURE (ATMOSPHERIC AIR)
13.	195-0882	[1]	BRACKET AS
14.	1K-3113	[1]	SPACER (0.546X0.840X3.875-IN THK)
15.	1S-0994	[1]	CLIP (LOOP)
16.	3J-1907	[1]	SEAL-O-RING
17.	3K-0360	[2]	SEAL-O-RING
18.	4D-7794	[1]	CLIP
19.	5C-2890 M	[2]	NUT (M6X1-THD)
20.	5C-7261 M	[3]	NUT (M8X1.25-THD)
21.	5P-4116	[8]	WASHER-HARD (8.8X20.5X2-MM THK)
22.	5P-4295	[1]	CLIP
23.	5P-9085	[2]	CLIP (LOOP)
24.	6D-4244	[2]	CLIP (LOOP)
25.	6D-4246	[7]	CLIP (LOOP)
26.	6D-4636	[1]	CLIP (LOOP)
27.	7J-0204	[1]	SEAL-O-RING
28.	8M-2770	[1]	CLIP (LOOP)
29.	8T-4121	[8]	WASHER-HARD (11X21X2.5-MM THK)
30.	8T-4122	[1]	WASHER-HARD (17X32X3.5-MM THK)
31.	8T-4136 M	[2]	BOLT (M10X1.5X25-MM)
32.	8T-4137 M	[6]	BOLT (M10X1.5X20-MM)
33.	8T-4189 M	[1]	BOLT (M8X1.25X20-MM)
34.	8T-4190 M	[1]	BOLT (M16X2X25-MM)
35.	8T-4200 M	[1]	BOLT (M8X1.25X16-MM)
36.	8T-4223	[1]	WASHER-HARD (13.5X25.5X3-MM THK)
37.	8T-5001 M	[1]	BOLT (M12X1.75X130-MM)
38.	9M-8406	[3]	CLIP (LOOP)
39.	9X-8256	[2]	WASHER (6.6X12X2-MM THK)
	C		CHANGE FROM PREVIOUS TYPE
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP32800347

258-7610: WIRING GP-ETHER STARTING AID

WIRING GP-ETHER STARTING AID

258-7610 WIRING GP-ETHER STARTING AID
S/N AYL1-UP
PART OF 253-7360 STARTING AID GP-ETHER

i02318830 SEBP3280

2587610 WIRING GP-ETHER STARTING AID Parts scheme

For full view, you need register

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	7K-1181	[11]	STRAP-CABLE
2.	258-7609	[1]	HARNESS AS-STARTING AID (ETHER)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
			(INCLUDES PLUG AS & WEDGE)

#SEBP32800348

190-5087: WIRING GP-FRONT

WIRING GP-FRONT

190-5087 WIRING GP-FRONT
S/N AYL1-766
PART OF 214-1368 CONVERSION AR-CERTIFICATION

i01477617 SEBP3280

For full view, you need register

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[6]	STRAP-CABLE
2.	4H-1225	[9]	WASHER (11X22X6-MM THK)
3.	5V-6152	[2]	CLAMP
4.	5V-6153	[1]	PLATE-COVER
5.	190-5088	[1]	HARNESS AS-FRONT CHASSIS
	102-8802	[4]	KIT-RECEPTACLE (2-PIN)
	102-8803	[3]	KIT-RECEPTACLE (3-PIN)
	102-8804	[2]	KIT-RECEPTACLE (4-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
	102-8801	[1]	KIT-RECEPTACLE (12-PIN)
	9X-0141	[1]	PLUG AS-CONNECTOR (40-PIN)
	3E-4367	[1]	RING-RETAINING
	3E-8557 M	[1]	BOLT (M5X0.8X39.37-MM)
	9X-3490	[2]	SEAL-CONNECTOR (40-PIN)
	155-2255	[1]	KIT-CONNECTING PLUG (12-PIN)
	155-2260	[3]	KIT-CONNECTING PLUG (3-PIN)
	155-2270	[7]	KIT-CONNECTING PLUG (2-PIN)
	155-2271	[2]	KIT-CONNECTING PLUG (4-PIN)
	155-2274	[1]	KIT-CONNECTING PLUG (6-PIN)
6.	033-8248	[1]	CLIP (LOOP)
7.	101-3625	[1]	CLIP
8.	130-5300	[8]	CLIP
9.	1S-0994	[1]	CLIP (LOOP)
10.	4D-7794	[1]	CLIP
11.	4K-8864	[4]	CLIP (LOOP)
12.	5P-7464	[1]	CLIP (SLOT)
13.	5P-7465	[1]	CLIP (TAB)
14.	8M-2773	[4]	CLIP (LOOP)
15.	8T-4121	[14]	WASHER-HARD (11X21X2.5-MM THK)
16.	8T-4133 M	[9]	NUT (M10X1.5-THD)
17.	8T-4136 M	[4]	BOLT (M10X1.5X25-MM)
18.	8T-4139 M	[1]	BOLT (M12X1.75X30-MM)
19.	8T-4195 M	[1]	BOLT (M10X1.5X30-MM)
20.	8T-4223	[1]	WASHER-HARD (13.5X25.5X3-MM THK)
21.	8T-4224	[1]	WASHER-HARD (8.8X16X2-MM THK)
22.	8T-4908 M	[1]	BOLT (M8X1.25X25-MM)
23.	8T-6974 M	[2]	BOLT (M6X1X80-MM)
24.	9M-8406	[5]	CLIP (LOOP)
25.	9X-8256	[2]	WASHER (6.6X12X2-MM THK)
	M		METRIC PART

#SEBP32800349

190-5087: WIRING GP-FRONT

WIRING GP-FRONT

190-5087 WIRING GP-FRONT
S/N AYL767-UP
PART OF 214-1368 CONVERSION AR-CERTIFICATION

i01909831 SEBP3280

For full view, you need register

Parts for your 950G II WHEEL LOADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	4H-1225	[6]	WASHER (11X22X6-MM THK)
2.	5V-6152	[2]	CLAMP
3.	5V-6153	[1]	PLATE-COVER
4.	7K-1181	[6]	STRAP-CABLE
5.	219-0605	[1]	HARNESS AS-FRONT CHASSIS
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
	102-8803	[3]	KIT-RECEPTACLE (3-PIN)
	102-8804	[2]	KIT-RECEPTACLE (4-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
	102-8801	[1]	KIT-RECEPTACLE (12-PIN)
	9X-0141	[1]	PLUG AS-CONNECTOR (40-PIN)
	3E-4367	[1]	RING-RETAINING
	3E-8557 M	[1]	BOLT (M5X0.8X39.37-MM)
	9X-3490	[2]	SEAL-CONNECTOR (40-PIN)
	155-2255	[1]	KIT-CONNECTING PLUG (12-PIN)
	155-2260	[3]	KIT-CONNECTING PLUG (3-PIN)
	155-2270	[7]	KIT-CONNECTING PLUG (2-PIN)
	155-2271	[2]	KIT-CONNECTING PLUG (4-PIN)
	155-2274	[1]	KIT-CONNECTING PLUG (6-PIN)
	8T-8737	[48]	PLUG-SEAL
6.	101-3625	[1]	CLIP
7.	124-0174	[2]	CLIP (LOOP)
8.	130-5300	[10]	CLIP
9.	4D-7794	[1]	CLIP
10.	4K-8864	[1]	CLIP (LOOP)
11.	5P-7464	[1]	CLIP (SLOT)
12.	5P-7465	[1]	CLIP (TAB)
13.	5P-9085	[1]	CLIP (LOOP)
14.	5P-9297	[1]	CLIP (LOOP)
15.	8M-2770	[1]	CLIP (LOOP)
16.	8M-2773	[6]	CLIP (LOOP)
17.	8T-4121	[15]	WASHER-HARD (11X21X2.5-MM THK)
18.	8T-4133 M	[10]	NUT (M10X1.5-THD)
19.	8T-4136 M	[2]	BOLT (M10X1.5X25-MM)
20.	8T-4137 M	[3]	BOLT (M10X1.5X20-MM)
21.	8T-4139 M	[1]	BOLT (M12X1.75X30-MM)
22.	8T-4223	[1]	WASHER-HARD (13.5X25.5X3-MM THK)
23.	8T-6974 M	[2]	BOLT (M6X1X80-MM)
24.	9M-8406	[2]	CLIP (LOOP)
25.	9X-8256	[2]	WASHER (6.6X12X2-MM THK)
26.	1S-0994	[1]	CLIP (LOOP)
	M		METRIC PART

Information:

ELECTRICAL AND STARTING SYSTEM

WIRING GP

Engine News

270-5051 Repair Kit (Electrical Connectors) Available for Repairs to Wiring Harnesses with Ampseal 16 and A4E 2 Connectors {0709, 1408}
2006/03/20

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2010/05/13

Special Instruction

Cross-Reference for Electrical Connectors {7553}
Cross-Reference for Electrical Connectors {7553}

Circuit Breaker Harness Assembly {1420}
Circuit Breaker Harness Assembly {1420}

Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}
Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}

Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}
Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}

Specifications

Electronic Control Wiring Group
3126B Engine for Caterpillar Built Machines

Tool Operating Manual

Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}
Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}

Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}

Testing and Adjusting

Electric Starting System - Test
3126B Engines

Troubleshooting

CID 0168 FMI 02 System Voltage intermittent/erratic
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0168 FMI 01 System Voltage Low
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0168 FMI 00 System Voltage High
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0291 FMI 05 Engine Cooling Fan Solenoid open circuit
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 0291 FMI 06 Engine Cooling Fan Solenoid short to ground
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

Electrical Connectors - Inspect
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0100 FMI 04 Engine Oil Pressure short to ground
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
3126B Engine for Caterpillar Built Machines

CID 0172 FMI 04 Intake Manifold Air Temp short to ground
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

CID 0273 FMI 03 Turbo Outlet Pressure open/short to +batt
3126B Engine for Caterpillar Built Machines

CID 0273 FMI 04 Turbo Outlet Pressure short to ground
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

CID 0274 FMI 04 Atmospheric Pressure short to ground
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0041 FMI 04 8 Volt DC Supply short to ground
3126B Engine for Caterpillar Built Machines

CID 0248 FMI 09 Cat Data Link not communicating
3126B Engine for Caterpillar Built Machines

CID 0091 FMI 08 Throttle Position signal abnormal
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 0548 FMI 06 Throttle Lock Lamp short
3126B Engine for Caterpillar Built Machines

CID 0548 FMI 05 Throttle Lock Lamp open circuit
3126B Engine for Caterpillar Built Machines

CID 0042 FMI 11 Inject Actuation Control Valve open/short
3126B Engine for Caterpillar Built Machines

CID 0094 FMI 03 Fuel Pressure open/short to +batt
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0094 FMI 04 Fuel Pressure short to ground
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0110 FMI 03 Engine Coolant Temperature open/short to +batt
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

CID 0110 FMI 04 Engine Coolant Temperature short to ground
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0164 FMI 00 High Injector Actuation Pressure
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0164 FMI 03 Injector Actuation Pressure voltage high
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 0175 FMI 03 Engine Oil Temperature open/short to +batt
3126B Engine for Caterpillar Built Machines

CID 0175 FMI 04 Engine Oil Temperature short to ground
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0267 FMI 02 Incorrect Engine Shutdown Switch inputs
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 0600 FMI 03 Hydraulic Oil Temperature open/short to +batt
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0600 FMI 04 Hydraulic Oil Temperature short to ground
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0041 FMI 03 8 Volt DC Supply short to +batt
3126B Engine for Caterpillar Built Machines

How To Use the Functional Tests
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

Sensors and Electrical Connectors
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

CID 0091 FMI 08 Throttle Position signal abnormal
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

CID 0164 FMI 11 Injector Actuation Pressure system fault
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

CID 0190 FMI 02 Loss of Engine Speed Signal
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

CID 0190 FMI 11 Engine Speed Sensor mechanical failure
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 0617 FMI 05 Air Inlet Heater Relay open/current below normal
3126B Engine for Caterpillar Built Machines

CID 1627 FMI 05 Fuel Pump Relay open circuit
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

CID 1627 FMI 06 Fuel Pump Relay short to ground
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

5 Volt Engine Pressure Sensor Supply Circuit - Test
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

Cat Data Link Circuit - Test
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

Engine Speed/Timing Sensor Circuit - Test
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

Injection Actuation Pressure Control Valve Circuit - Test
3126B Engine for Caterpillar Built Machines

Throttle Switch Circuit - Test
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

Low Engine Oil Pressure Lamp Circuit - Test
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

Air Inlet Heater Circuit - Test
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

Throttle Position Sensor Circuit - Test
3126B Engine for Caterpillar Built Machines

Digital Sensor Supply Circuit - Test
3126B Engine for Caterpillar Built Machines

Electrical Power Supply Circuit - Test
3126B Engine for Caterpillar Built Machines

CID 0290 FMI 03 Engine Fan Pump Pressure open/short to +batt
3126B Engine for Caterpillar Built Machines

CID 0290 FMI 04 Engine Fan Pump Pressure short to ground
3126B Engine for Caterpillar Built Machines

Engine Fan Control Solenoid Circuit - Test
3126B Engine for Caterpillar Built Machines

Throttle Lock Switch Circuit - Test
3126B Engine for Caterpillar Built Machines

Throttle Lock Lamp Circuit - Test
3126B Engine for Caterpillar Built Machines

Digital Sensor Supply Circuit - Test
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

Throttle Position Sensor Circuit - Test
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

Electrical Power Supply Circuit - Test
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

Fuel Pump Relay Circuit - Test
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

CID 1582 FMI 03 Trans Lube Oil Temp Sensor open/short to +batt
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 1582 FMI 04 Trans Lube Oil Temp Sensor short to ground
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 1589 FMI 03 Turbo Inlet Air Pressure Sensor open/shrt to +bat
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

Air Filter Restriction Lamp - Test
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

Engine Shutdown Switch Circuit - Test
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

Engine Fan Control Solenoid Circuit - Test
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0617 FMI 05 Air Inlet Heater Relay open/current below normal
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0617 FMI 06 Air Inlet Heater Relay grounded/current above norm
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

Sensors and Electrical Connectors
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 0342 FMI 03 Secondary Engine Speed open/short to +batt
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

Engine Shutdown Switch Circuit - Test
3126B Engine for Caterpillar Built Machines

Engine Fan Reversing Solenoid Circuit - Test
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 0164 FMI 02 Injector Actuation Pressure signal erratic
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 0342 FMI 02 Loss of Secondary Engine Speed signal
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

Air Inlet Heater Circuit - Test
3126B Engine for Caterpillar Built Machines

CID 0164 FMI 04 Injector Actuation Pressure voltage low
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

Engine Pressure Sensor Open or Short Circuit - Test
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit

CID 0342 FMI 11 Secondary Engine Speed Sensor mechanical failure
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

Cat Data Link Circuit - Test
3126B Engine for Caterpillar Built Machines

Sensors and Electrical Connectors
3126B Engine for Caterpillar Built Machines

5 Volt Engine Pressure Sensor Supply Circuit - Test
3126B Engine for Caterpillar Built Machines

Engine Pressure Sensor Open or Short Circuit - Test
3126B Engine for Caterpillar Built Machines

Sensors and Electrical Connectors
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

Analog Sensor Supply Circuit - Test
3126B Engines for the IT38G Series II Integrated Toolcarrier and the 938G Series II Wheel Loader

CID 0485 FMI 03 Engine Fan Rev Solenoid short to +batt
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 0485 FMI 04 Engine Fan Rev Solenoid short to ground
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

Engine Wiring Information
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 1589 FMI 04 Turbo Inlet Air Pressure Sensor short to ground
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders

CID 0617 FMI 06 Air Inlet Heater Relay grounded/current above norm
3126B Engine for Caterpillar Built Machines

Service Magazine

Dielectric Grease Should Not Be Used in Electrical Connectors {1408, 7553}
2012/05/04

Service of the Machined Terminals and the Stamped and Formed Terminals {7553}
2006/11/13

Updated Instruction For The Bypass Harness {0785, 1408}
2008/03/17

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2012/03/05

Striped Wire Is Replaced With Improved Ink Jet Identification for Legacy (Parts Service) Wire harnesses {1408}
2012/06/08

Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553, 7556}
2012/05/08

Information On Battery Cables and Wire Assemblies for Assembling at Dealer Site {4459}
2012/09/21