178-0163 WIRING GP-REAR -SERVICE CENTER S/N APM2575-UP PART OF 185-3143 SERVICE CENTER AR 140H MOTOR GRADER

ELECTRICAL AND STARTING SYSTEM

WIRING GP

0. 178-0163 WIRING GP-
1. 251-1080 WIRING GP-
2. 251-1080 WIRING GP-
3. 322-8611 WIRING GP-

LIGHTING GP

4. 184-1299 WIRING GP-
5. 193-8253 WIRING GP-
6. 318-1141 WIRING GP-

WIRING GP

7. 161-1020 WIRING GP-
8. 161-1020 WIRING GP-

SENSOR GP

9. 247-6438 WIRING GP-
0. INFORMATION

MOTOR GRADER 140H MOTOR GRADER APM
140H Motor Grader APM00001-UP (MACHINE) POWERED BY 3176C Engine SEBP3293 140H APM (2001)

ELECTRICAL AND STARTING SYSTEM

WIRING GP

178-0163 WIRING GP-REAR

251-1080 WIRING GP-REAR

322-8611 WIRING GP-REAR

#SEBP32930390

178-0163: WIRING GP-REAR

WIRING GP-REAR

178-0163 WIRING GP-REAR -SERVICE CENTER
S/N APM2575-UP
PART OF 185-3143 SERVICE CENTER AR

i02712612 SEBP3293

For full view, you need register

Parts for your 140H MOTOR GRADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	2L-0273	[1]	FITTING (RUBBER)
2.	3E-8320	[1]	PLATE-INSTRUCTION (BATTERY)
3.	3S-2093	[2]	STRAP-CABLE
4.	6V-4283	[1]	PLATE-IDENTIFICATION (ALTERNATOR RESET)
5.	7V-9275	[1]	STRAP
6.	112-4428	[1]	CABLE AS
	1S-7251	[1]	TERMINAL-CABLE (00-GA, 1/2-IN SCREW)
	1S-7252	[1]	TERMINAL-CABLE (00-GA, 3/8-IN SCREW)
	5P-0747 BE		CABLE (00-GA, BLACK)(27-CM)
7.	115-5593	[1]	CABLE AS
	1S-7252	[1]	TERMINAL-CABLE (00-GA, 3/8-IN SCREW)
	5P-0747 BE		CABLE (00-GA, BLACK)(119-CM)
	7N-5274	[1]	COVER AS-TERMINAL (BLACK)
	3S-6050	[1]	TERMINAL AS-BATTERY (NEGATIVE)
	1M-6119	[1]	BOLT (5/16-18X1.375-IN)
	1M-6120	[1]	NUT (5/16-18-THD)
8.	118-3534 Y	[1]	SWITCH GP-MAGNETIC (24-VOLT)(STARTER RELAY)
9.	125-6390	[1]	PLATE-INFORMATION (ENGINE)
10.	167-0138 Y	[1]	SWITCH GP-MAGNETIC (24-VOLT)(MAIN RELAY)
11.	169-5414	[1]	CLIP
12.	169-7262	[1]	HARNESS AS-REAR (SERVICE CENTER, RH)
	127-5484	[1]	RECEPTACLE AS-CONNECTOR (1-PIN)
	127-5486	[1]	RECEPTACLE AS-CONNECTOR (1-PIN)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(EACH INCLUDES RECEPTACLE AS & WEDGE)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
	155-2274	[2]	KIT-CONNECTING PLUG (6-PIN)
			(EACH INCLUDES PLUG AS, WEDGE, & INTERFACE SEAL)
	114-8843 BE		SLEEVE-PLASTIC
	125-7875 BE		TUBE-HEAT SHRINK (7.44-MM DIA)
13.	169-7263	[1]	HARNESS AS-REAR (SERVICE CENTER, LH)
	155-2272	[1]	PLUG AS-CONNECTOR (4-PIN)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
	102-8804	[1]	KIT-RECEPTACLE (4-PIN)
	102-8805	[1]	KIT-RECEPTACLE (6-PIN)
	102-8801	[1]	KIT-RECEPTACLE (12-PIN)
			(EACH INCLUDES RECEPTACLE AS & WEDGE)
	155-2270	[1]	KIT-CONNECTING PLUG (2-PIN)
			(INCLUDES PLUG AS, WEDGE, & INTERFACE SEAL)
	101-8106	[1]	LOCK-CONNECTOR
	101-8108	[1]	PLUG-CONNECTOR
	125-7875 BE		TUBE-HEAT SHRINK (7.44-MM DIA)(5-CM)
14.	171-2210	[1]	CIRCUIT BREAKER AS (80-AMPERE)(MAIN)
14A.	171-2210	[1]	CIRCUIT BREAKER AS (80-AMPERE)(ALTERNATOR)
			(EACH CIRCUIT BREAKER AS INCLUDES)
	8T-4205	[2]	WASHER-HARD (7.2X14.5X2-MM THK)
	6V-8187	[2]	NUT (1/4-28-THD)
	253-2111	[2]	LOCKWASHER
15.	174-3897	[1]	CABLE AS
	1S-7251	[2]	TERMINAL-CABLE (00-GA, 1/2-IN SCREW)
	5P-0761 BE		CABLE (00-GA, RED)(117-CM)
	8N-0869	[2]	COVER-TERMINAL (RED)
16.	177-8802	[1]	CABLE AS
	1S-7251	[1]	TERMINAL-CABLE (00-GA, 1/2-IN SCREW)
	5P-0761 BE		CABLE (00-GA, RED)(32-CM)
	8N-0869	[1]	COVER-TERMINAL (RED)
	8N-1725	[1]	COVER AS-TERMINAL (RED)
	3S-6049	[1]	TERMINAL AS-BATTERY (POSITIVE)
	1M-6119	[1]	BOLT (5/16-18X1.375-IN)
	1M-6120	[1]	NUT (5/16-18-THD)
17.	177-9813	[1]	CABLE AS
	5P-5675 BD		WIRE (6-GA, BLACK)
	2L-8050	[1]	TERMINAL-RING (6-GA, 1/4-IN SCREW)
	2L-8058	[1]	TERMINAL-RING (8-GA, 1/4-IN SCREW)
	8N-1546	[1]	PIN-CONNECTOR (6-GA)
	127-5484	[1]	RECEPTACLE AS-CONNECTOR (1-PIN)
	114-8843 BE		SLEEVE-PLASTIC
18.	177-9814	[1]	CABLE AS
	8N-1548	[1]	PIN-CONNECTOR (4-GA)
	114-8843 BE		SLEEVE-PLASTIC
	6V-2369 BD		CABLE (4-GA, BLACK)
	9G-4343	[1]	TERMINAL-RING (4-GA, 1/4-IN SCREW)
	7T-4369	[1]	PIN-CONNECTOR
	127-5484	[1]	RECEPTACLE AS-CONNECTOR (1-PIN)
19.	178-0160	[1]	WIRE AS
20.	178-0162	[1]	CABLE AS
	5P-5689 BD		WIRE (8-GA, BLACK)
	2L-8050	[1]	TERMINAL-RING (6-GA, 1/4-IN SCREW)
	2L-8058	[1]	TERMINAL-RING (8-GA, 1/4-IN SCREW)
21.	178-0555	[1]	CABLE AS
	6V-2369 BD		CABLE (4-GA, BLACK)
	9G-4343	[1]	TERMINAL-RING (4-GA, 1/4-IN SCREW)
	5P-3454	[1]	TERMINAL-RING (4-GA, 5/16-IN SCREW)
22.	189-0108	[1]	PLATE
23.	194-1854	[1]	COVER
24.	195-4990	[1]	WIRE AS
25.	249-4364	[2]	SPACER
26.	033-8248	[1]	CLIP (LOOP)
27.	130-5300	[3]	CLIP
28.	157-2528	[1]	SPACER (7X16X20-MM THK)
29.	174-5907	[6]	CLIP (LOOP)
30.	1S-0994	[2]	CLIP (LOOP)
31.	1S-1015	[1]	CLIP (LOOP)
32.	1V-6688	[1]	GROMMET
33.	3K-8106	[2]	SCREW-MACHINE (8-32X1-IN)
34.	4B-4274	[4]	WASHER (5.5X13X1.2-MM THK)
35.	4B-4863	[2]	WASHER (4.7X11X1.2-MM THK)
36.	4D-7794	[4]	CLIP
37.	4D-8948	[1]	CLIP
38.	4H-2558	[2]	GROMMET
39.	5L-4507	[4]	SCREW-MACHINE (10-32X0.875-IN)
40.	5P-4116	[1]	WASHER-HARD (8.8X20.5X2-MM THK)
41.	5P-4295	[1]	CLIP
42.	6D-3479	[1]	CLIP (LOOP)
43.	6K-8178	[1]	CLIP (LOOP)
44.	6T-3643	[1]	CIRCUIT BREAKER AS (15-AMPERE)(ENGINE CONTROL)
	6V-8376	[2]	SCREW-MACHINE (8-32X0.25-IN)
	9B-7233	[2]	LOCKWASHER
45.	6V-7357 M	[1]	BOLT (M6X1X25-MM)
46.	7N-0718 Y	[1]	SWITCH GP-DISCONNECT (BATTERY)(BATTERY)
47.	7N-3718	[1]	CLIP
48.	7Y-8169	[1]	GROMMET
49.	8C-8451 M	[1]	BOLT (M6X1X40-MM)
50.	8M-2772	[1]	CLIP (LOOP)
51.	8T-0293 M	[1]	BOLT (M12X1.75X20-MM)
52.	8T-4121 C	[15]	WASHER-HARD (11X21X2.5-MM THK)
53.	8T-4136 CM	[9]	BOLT (M10X1.5X25-MM)
54.	8T-4137 M	[6]	BOLT (M10X1.5X20-MM)
55.	8T-4138 M	[2]	BOLT (M6X1X20-MM)
56.	8T-4189 M	[1]	BOLT (M8X1.25X20-MM)
57.	8T-4191 M	[2]	BOLT (M10X1.5X16-MM)
58.	8T-4205	[4]	WASHER-HARD (7.2X14.5X2-MM THK)
59.	8T-4223	[1]	WASHER-HARD (13.5X25.5X3-MM THK)
60.	9W-0742 Y	[1]	BLOCK GP-JUNCTION (BATTERY)
	B		USE AS REQUIRED
	C		CHANGE FROM PREVIOUS TYPE
	D		ORDER BY THE METER
	E		ORDER BY THE CENTIMETER
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP32930391

251-1080: WIRING GP-REAR

WIRING GP-REAR

251-1080 WIRING GP-REAR
S/N APM1-UP
PART OF 247-6453 GRADE CONTROL AR
Type 1
AN ATTACHMENT

i02223919 SEBP3293

For full view, you need register

Parts for your 140H MOTOR GRADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[5]	STRAP-CABLE
2.	125-6390	[1]	PLATE-INFORMATION (ENGINE)
3.	244-5873	[1]	WIRE AS
4.	246-1682	[1]	WIRE AS
5.	132-5789	[1]	CLIP (LADDER)
6.	3K-8106	[2]	SCREW-MACHINE (8-32X1-IN)
7.	4B-4863	[2]	WASHER (4.7X11X1.2-MM THK)
8.	4D-7794	[2]	CLIP
9.	5P-9297	[7]	CLIP (LOOP)
10.	6T-3644	[1]	CIRCUIT BREAKER AS (20-AMPERE)
	6V-8376	[2]	SCREW-MACHINE (8-32X0.25-IN)
	9B-7233	[2]	LOCKWASHER

#SEBP32930392

251-1080: WIRING GP-REAR

WIRING GP-REAR

251-1080 WIRING GP-REAR
S/N APM1-UP
PART OF 247-6453 GRADE CONTROL AR
Type 2
AN ATTACHMENT

i02304772 SEBP3293

For full view, you need register

Parts for your 140H MOTOR GRADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093 C	[6]	STRAP-CABLE
2.	125-6390	[1]	PLATE-INFORMATION (ENGINE)
3.	246-1682	[1]	WIRE AS
4.	132-5789	[1]	CLIP (LADDER)
5.	263-9458 C	[1]	WIRE AS
6.	4B-4863	[2]	WASHER (4.7X11X1.2-MM THK)
7.	4D-7794 C	[1]	CLIP
8.	6T-3644	[1]	CIRCUIT BREAKER AS (20-AMPERE)
	6V-8376	[2]	SCREW-MACHINE (8-32X0.25-IN)
	9B-7233	[2]	LOCKWASHER
9.	9M-4704	[2]	BOLT (8-32X1-IN)
	C		CHANGE FROM PREVIOUS TYPE

#SEBP32930393

322-8611: WIRING GP-REAR

WIRING GP-REAR

322-8611 WIRING GP-REAR
S/N APM1-UP
FIELD INSTALLATION

i03317600 SEBP3293

For full view, you need register

Parts for your 140H MOTOR GRADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	2B-0941	[1]	SPACER (10.5X19X19-MM THK)
2.	3S-2093	[1]	STRAP-CABLE
4.	8X-8450	[2]	PLATE
5.	307-3645	[1]	HARNESS AS-REAR (CAB)
6.	307-3646	[1]	HARNESS AS-REAR (CHASSIS, REAR)
7.	307-3647	[1]	HARNESS AS-TRANSMISSION
8.	307-6241	[2]	BLOCK-CLAMP
9.	307-6242	[2]	BLOCK-CLAMP
10.	307-6243	[4]	BLOCK-CLAMP
11.	307-7500	[2]	BLOCK-CLAMP
12.	307-7501	[1]	PLATE AS
13.	307-7502	[1]	PLATE
14.	313-4181	[1]	BRACKET AS
15.	033-8248	[1]	CLIP (LOOP)
16.	130-5300	[1]	CLIP
17.	1S-0994	[1]	CLIP (LOOP)
18.	1S-0996	[2]	CLIP
19.	3K-6060	[4]	LOCKNUT (3/8-16-THD)
20.	4D-7388	[2]	CLIP (LOOP)
21.	4D-7794	[5]	CLIP
22.	4K-8864	[1]	CLIP (LOOP)
23.	4P-7581	[1]	CLIP (LADDER)
24.	4S-4455	[3]	CLIP
25.	6D-4244	[3]	CLIP (LOOP)
26.	6D-4246	[3]	CLIP (LOOP)
27.	7C-4354	[5]	CLIP
28.	8D-9671	[1]	CLIP
29.	8M-2773	[4]	CLIP (LOOP)
30.	8T-0389 M	[4]	LOCKNUT (M10X1.5-THD)
31.	8T-4121	[12]	WASHER-HARD (11X21X2.5-MM THK)
32.	8T-4133 M	[1]	NUT (M10X1.5-THD)
33.	8T-4136 M	[1]	BOLT (M10X1.5X25-MM)
34.	8T-4137 M	[1]	BOLT (M10X1.5X20-MM)
35.	8T-4186 M	[1]	BOLT (M10X1.5X40-MM)
	M		METRIC PART

#SEBP32930394

184-1299: WIRING GP-REAR LIGHTING

WIRING GP-REAR LIGHTING

184-1299 WIRING GP-REAR LIGHTING -BACKUP ALARM, LIGHTS
S/N APM1-UP
PART OF 159-4615 GENERAL AR

i01515785 SEBP3293

1841299 WIRING GP-REAR LIGHTING Parts scheme

For full view, you need register

Parts for your 140H MOTOR GRADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[9]	STRAP-CABLE
2.	213-9100	[1]	ALARM AS (BACKUP)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	5P-5623 BD		WIRE-ELECTRICAL (16-GA, BLACK)
	186-3735	[2]	PIN-CONNECTOR (16-GA TO 18-GA)
	9X-1813 BE		SLEEVE
3.	231-4527	[1]	HARNESS AS-REAR LIGHTING
	102-8802	[2]	KIT-RECEPTACLE (2-PIN)
	102-8801	[1]	KIT-RECEPTACLE (12-PIN)
			(EACH INCLUDES RECEPTACLE AS & WEDGE)
	155-2260	[2]	KIT-CONNECTING PLUG (3-PIN)
	155-2270	[3]	KIT-CONNECTING PLUG (2-PIN)
			(EACH INCLUDES PLUG AS & WEDGE)
4.	130-5300	[5]	CLIP
5.	135-0426 Y	[2]	LAMP GP-SIGNAL (24-VOLT, STOP, TAIL)
6.	5C-2890 M	[6]	NUT (M6X1-THD)
7.	5P-4116	[4]	WASHER-HARD (8.8X20.5X2-MM THK)
8.	8T-4189 M	[4]	BOLT (M8X1.25X20-MM)
9.	8T-4224	[6]	WASHER-HARD (8.8X16X2-MM THK)
10.	4D-9517	[1]	CLIP (SLOT)
	B		USE AS REQUIRED
	D		ORDER BY THE METER
	E		ORDER BY THE CENTIMETER
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP32930395

193-8253: WIRING GP-REAR LIGHTING

WIRING GP-REAR LIGHTING

193-8253 WIRING GP-REAR LIGHTING -EU
S/N APM1-UP
AN ATTACHMENT

i01508295 SEBP3293

1938253 WIRING GP-REAR LIGHTING Parts scheme

For full view, you need register

Parts for your 140H MOTOR GRADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3E-5239	[1]	RELAY AS (24-VOLT)
2.	3S-2093	[13]	STRAP-CABLE
3.	5C-9930	[1]	LAMP GP (RH)
	4V-8116	[1]	LAMP (24-VOLT, 5-WATT)(TAIL)
	5C-9584	[2]	LAMP (24-VOLT, 21-WATT)(STOP)
	6C-0109	[1]	LAMP AS (STOP, TURN, TAIL, RH)
	5M-6725	[1]	SCREW-TAPPING (8-18X0.625-IN)
	8L-5828	[1]	SCREW-TAPPING (8-18X0.875-IN)
	188-9694	[1]	LENS (RED, YELLOW)
	188-9695	[1]	SEAL
4.	5C-9931	[1]	LAMP GP (LH)
	4V-8116	[1]	LAMP (24-VOLT, 5-WATT)(TAIL)
	5C-9584	[2]	LAMP (24-VOLT, 21-WATT)(STOP)
	6C-0110	[1]	LAMP AS (STOP, TAIL, TURN, LH)
	5M-6725	[1]	SCREW-TAPPING (8-18X0.625-IN)
	8L-5828	[1]	SCREW-TAPPING (8-18X0.875-IN)
	188-9694	[1]	LENS (RED, YELLOW)
	188-9695	[1]	SEAL
5.	6C-5233	[1]	BRACKET AS (RH)
	8T-3490 M	[2]	NUT-WELD (M10X1.5-THD)
6.	6C-5234	[1]	BRACKET AS (LH)
	8T-3490 M	[2]	NUT-WELD (M10X1.5-THD)
7.	7K-1181	[7]	STRAP-CABLE
8.	7V-7835	[1]	ARM AS (RH)
	5C-9563	[1]	SPACER (11.02X26.67X55-MM THK)
9.	7V-7838	[1]	ARM AS (LH)
	5C-9563	[1]	SPACER (11.02X26.67X55-MM THK)
10.	7X-2393	[4]	BUMPER-CONICAL
11.	9S-1316	[2]	SPRING
12.	9G-7101	[1]	SPACER (11X20X30-MM THK)
13.	112-5555	[2]	ROD
14.	156-0283	[2]	WASHER-HARD (8.4X35X2.5-MM THK)
15.	160-1744	[2]	BRACKET
16.	196-4609	[1]	HARNESS AS-REAR LIGHTING
	102-8802	[2]	KIT-RECEPTACLE (2-PIN)
	102-8801	[1]	KIT-RECEPTACLE (12-PIN)
			(EACH INCLUDES RECEPTACLE AS & WEDGE)
	155-2270	[2]	KIT-CONNECTING PLUG (2-PIN)
	155-2271	[2]	KIT-CONNECTING PLUG (4-PIN)
			(EACH INCLUDES PLUG AS & WEDGE)
17.	208-7933	[2]	PLATE
18.	213-1413	[1]	HARNESS AS-REAR LIGHTING (RH)
	102-8804	[1]	KIT-RECEPTACLE (4-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
19.	213-1414	[1]	HARNESS AS-REAR LIGHTING (LH)
	102-8804	[1]	KIT-RECEPTACLE (4-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
20.	213-9100	[1]	ALARM AS (BACKUP)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	186-3735	[2]	PIN-CONNECTOR (16-GA TO 18-GA)
	5P-5623 D		WIRE-ELECTRICAL (16-GA, BLACK)(0.4-M)
	9X-1813 E		SLEEVE (31-CM)
21.	291-1049	[1]	PLATE
22.	306-3046	[1]	HARNESS AS-REAR
23.	130-5300	[3]	CLIP
24.	2V-3216	[2]	CLIP (LOOP)
25.	3B-5301	[2]	PIN-COTTER
26.	5C-2890 M	[7]	NUT (M6X1-THD)
27.	5C-7261 M	[4]	NUT (M8X1.25-THD)
28.	5P-1076	[2]	WASHER-HARD (13.5X30X4-MM THK)
29.	5P-4116	[4]	WASHER-HARD (8.8X20.5X2-MM THK)
30.	5P-9297	[1]	CLIP (LOOP)
31.	7G-7053	[2]	GROMMET
32.	8D-5641	[4]	BEARING
33.	8T-2501	[1]	BOLT (3/8-16X2-IN)
34.	8T-4121	[8]	WASHER-HARD (11X21X2.5-MM THK)
35.	8T-4122	[4]	WASHER-HARD (17X32X3.5-MM THK)
36.	8T-4133 M	[2]	NUT (M10X1.5-THD)
37.	8T-4136 M	[6]	BOLT (M10X1.5X25-MM)
38.	8T-4138 M	[1]	BOLT (M6X1X20-MM)
39.	8T-4139 M	[2]	BOLT (M12X1.75X30-MM)
40.	8T-4171 M	[2]	BOLT (M6X1X12-MM)
41.	8T-4173 M	[2]	BOLT (M16X2X110-MM)
42.	8T-4189 M	[4]	BOLT (M8X1.25X20-MM)
43.	8T-4205	[6]	WASHER-HARD (7.2X14.5X2-MM THK)
44.	8T-4223	[2]	WASHER-HARD (13.5X25.5X3-MM THK)
45.	8T-4224	[4]	WASHER-HARD (8.8X16X2-MM THK)
46.	8T-4778 M	[2]	LOCKNUT (M16X2-THD)
47.	8T-4896	[1]	WASHER-HARD (10.2X18.5X2.5-MM THK)
48.	9X-6165	[2]	WASHER (6.5X22X2.5-MM THK)
	D		ORDER BY THE METER
	E		ORDER BY THE CENTIMETER
	M		METRIC PART

#SEBP32930396

318-1141: WIRING GP-REAR LIGHTING

WIRING GP-REAR LIGHTING

318-1141 WIRING GP-REAR LIGHTING
S/N APM1-UP
FIELD INSTALLATION

i02918722 SEBP3293

3181141 WIRING GP-REAR LIGHTING Parts scheme

For full view, you need register

Parts for your 140H MOTOR GRADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3E-5239	[1]	RELAY AS (24-VOLT)(BRAKE LIGHT)
2.	7K-1181	[8]	STRAP-CABLE
3.	9G-7101	[1]	SPACER (11X20X30-MM THK)
4.	291-1049	[1]	PLATE
5.	306-3046	[1]	HARNESS AS-REAR
6.	4P-8134	[1]	CLIP (LADDER)
7.	5C-2890 M	[1]	NUT (M6X1-THD)
8.	8T-2501	[1]	BOLT (3/8-16X2-IN)
9.	8T-4121	[1]	WASHER-HARD (11X21X2.5-MM THK)
10.	8T-4138 M	[1]	BOLT (M6X1X20-MM)
11.	9X-6165	[2]	WASHER (6.5X22X2.5-MM THK)
	M		METRIC PART

#SEBP32930397

161-1020: WIRING GP-SECONDARY STEERING

WIRING GP-SECONDARY STEERING

161-1020 WIRING GP-SECONDARY STEERING
S/N APM1-216
PART OF 166-3302 STEERING AR-SECONDARY
AN ATTACHMENT

i01485949 SEBP3293

1611020 WIRING GP-SECONDARY STEERING Parts scheme

For full view, you need register

Parts for your 140H MOTOR GRADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	2L-0273	[1]	FITTING (RUBBER)
2.	3E-6450	[1]	SWITCH AS-PRESSURE (SECONDARY STEERING)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
	3E-3371	[1]	WEDGE-RECEPTACLE LOCK (3-PIN)
	8T-8729	[3]	PIN-CONNECTOR (16-GA TO 20-GA)
3.	3E-7842	[1]	RESISTOR AS (SECONDARY STEERING INDICATOR)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
	3E-3365	[1]	WEDGE-RECEPTACLE LOCK (2-PIN)
	6T-3610	[1]	RESISTOR
	8T-8729	[2]	PIN-CONNECTOR (16-GA TO 20-GA)
4.	9W-1442	[2]	FUSE (10-AMPERE)(SECONDARY STEERING)
5.	132-6640 Y	[1]	CONTROL GP-SECONDARY STEERING
6.	134-3355	[1]	STRAP AS
7.	140-8864	[1]	CABLE AS
	1S-7252	[2]	TERMINAL-CABLE (00-GA, 3/8-IN SCREW)
	5P-0747	[20]	CABLE (00-GA, BLACK)
8.	178-0101	[1]	CABLE AS
	1S-7252	[1]	TERMINAL-CABLE (00-GA, 3/8-IN SCREW)
	5P-0761	[109]	CABLE (00-GA, RED)
	8N-0869	[1]	COVER-TERMINAL (RED)
	9X-9825	[1]	TERMINAL-CABLE (00-GA, 1/2-IN SCREW)
9.	178-0102	[1]	CABLE AS
	1S-7252	[2]	TERMINAL-CABLE (00-GA, 3/8-IN SCREW)
	5P-0761	[145]	CABLE (00-GA, RED)
	8N-0869	[2]	COVER-TERMINAL (RED)
10.	197-1459	[1]	PLATE
12.	3E-0154 Y	[1]	SWITCH GP-MAGNETIC (SECONDARY STEERING)
13.	3E-6754	[1]	GROMMET
14.	3K-0360	[1]	SEAL-O-RING
15.	5C-2890 M	[2]	NUT (M6X1-THD)
16.	5M-3062	[1]	BOLT (3/8-16X0.75-IN)
17.	6V-1322	[4]	BOLT (1/4-20X0.375-IN)
18.	7X-0507	[1]	WASHER-HARD (12X22.5X5-MM THK)
19.	8T-4121	[2]	WASHER-HARD (11X21X2.5-MM THK)
20.	8T-4136 M	[2]	BOLT (M10X1.5X25-MM)
21.	8T-4137 M	[2]	BOLT (M10X1.5X20-MM)
22.	8T-4205	[4]	WASHER-HARD (7.2X14.5X2-MM THK)
23.	8T-4896	[1]	WASHER-HARD (10.2X18.5X2.5-MM THK)
24.	174-5907	[4]	CLIP (LOOP)
25.	9X-2045 M	[2]	SCREW-TRUSS HEAD (M6X1X20-MM)
26.	9X-8256	[2]	WASHER (6.6X12X2-MM THK)
27.	3E-8765	[1]	SWITCH AS (24-VOLT)(SECONDARY STEERING)
	3E-8816	[1]	ACTUATOR
	3E-8825	[2]	LAMP (24-VOLT)(SECONDARY STEERING SWITCH)
28.	3S-2093	[1]	STRAP-CABLE
29.	9L-1566	[1]	SUPPORT
30.	130-5300	[1]	CLIP
31.	194-2903	[1]	ELBOW AS
	8T-0119	[1]	ELBOW
	3K-0360	[1]	SEAL-O-RING
32.	195-0434	[1]	BRACKET
33.	8T-4133 M	[1]	NUT (M10X1.5-THD)
34.	6V-8801	[2]	NUT (3/8-16-THD)
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP32930398

161-1020: WIRING GP-SECONDARY STEERING

WIRING GP-SECONDARY STEERING

161-1020 WIRING GP-SECONDARY STEERING
S/N APM217-UP
PART OF 166-3302 STEERING AR-SECONDARY
AN ATTACHMENT

i01708818 SEBP3293

For full view, you need register

Parts for your 140H MOTOR GRADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	2L-0273	[1]	FITTING (RUBBER)
2.	3E-0154 Y	[1]	SWITCH GP-MAGNETIC (SECONDARY STEERING)
3.	3E-6450	[1]	SWITCH AS-PRESSURE (SECONDARY STEERING)
	102-8803	[1]	KIT-RECEPTACLE (3-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	186-3735	[3]	PIN-CONNECTOR (16-GA TO 18-GA)
4.	3E-7842	[1]	RESISTOR AS (SECONDARY STEERING INDICATOR)
	102-8802	[1]	KIT-RECEPTACLE (2-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	6T-3610	[1]	RESISTOR
	186-3735	[2]	PIN-CONNECTOR (16-GA TO 18-GA)
5.	3S-2093	[2]	STRAP-CABLE
6.	9L-1566	[1]	SUPPORT
7.	9W-1442	[2]	FUSE (10-AMPERE)(SECONDARY STEERING)
8.	118-7809	[1]	PLATE
9.	132-6640 Y	[1]	CONTROL GP-SECONDARY STEERING
10.	134-3355	[1]	STRAP AS
11.	140-8864	[1]	CABLE AS
	1S-7252	[2]	TERMINAL-CABLE (00-GA, 3/8-IN SCREW)
	5P-0747 E		CABLE (00-GA, BLACK)(20CM)
12.	178-0101	[1]	CABLE AS
	1S-7252	[1]	TERMINAL-CABLE (00-GA, 3/8-IN SCREW)
	5P-0761 E		CABLE (00-GA, RED)(87CM)
	8N-0869	[1]	COVER-TERMINAL (RED)
	9X-9825	[1]	TERMINAL-CABLE (00-GA, 1/2-IN SCREW)
13.	178-0102	[1]	CABLE AS
	1S-7252	[2]	TERMINAL-CABLE (00-GA, 3/8-IN SCREW)(148CM)
	5P-0761 E		CABLE (00-GA, RED)(148CM)
	9X-6932	[2]	BOOT-TERMINAL
14.	194-2903	[1]	ELBOW AS
	8T-0119	[1]	ELBOW
	3K-0360	[1]	SEAL-O-RING
15.	195-0434	[1]	BRACKET
16.	197-1459	[1]	PLATE
17.	130-5300	[1]	CLIP
18.	174-5907	[3]	CLIP (LOOP)
19.	3E-6754	[1]	GROMMET
20.	3K-0360	[1]	SEAL-O-RING
21.	5C-2890 M	[2]	NUT (M6X1-THD)
22.	5M-3062	[2]	BOLT (3/8-16X0.75-IN)
23.	6V-1322	[4]	BOLT (1/4-20X0.375-IN)
24.	6V-8801	[2]	NUT (3/8-16-THD)
25.	8T-4121	[7]	WASHER-HARD (11X21X2.5-MM THK)
26.	8T-4133 M	[2]	NUT (M10X1.5-THD)
27.	8T-4137 M	[5]	BOLT (M10X1.5X20-MM)
28.	8T-4205	[4]	WASHER-HARD (7.2X14.5X2-MM THK)
29.	8T-4896	[4]	WASHER-HARD (10.2X18.5X2.5-MM THK)
31.	9X-2045 M	[2]	SCREW-TRUSS HEAD (M6X1X20-MM)
32.	9X-8256	[2]	WASHER (6.6X12X2-MM THK)
33.	3E-8765	[1]	SWITCH AS (24-VOLT)(SECONDARY STEERING)
	3E-8816	[1]	ACTUATOR
	3E-8825	[2]	LAMP (24-VOLT)(SECONDARY STEERING SWITCH)
	E		ORDER BY THE CENTIMETER
	M		METRIC PART
	Y		SEPARATE ILLUSTRATION

#SEBP32930399

247-6438: WIRING GP-SENSOR

WIRING GP-SENSOR

247-6438 WIRING GP-SENSOR -CROSS SLOPE
S/N APM1-UP
PART OF 250-1932 WIRING GP-SENSOR
FOR USE WITH 12H, 135H
AN ATTACHMENT

i02279714 SEBP3293

For full view, you need register

Parts for your 140H MOTOR GRADER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3S-2093	[1]	STRAP-CABLE
2.	9G-9154	[2]	CLIP
3.	236-2356	[1]	HARNESS AS-SENSOR (ANGLE)
	102-8804	[1]	KIT-RECEPTACLE (4-PIN)
			(INCLUDES RECEPTACLE AS & WEDGE)
	9X-4385	[1]	PLUG AS-CONNECTOR (6-PIN)
4.	243-3250	[1]	HARNESS AS-SENSOR (ROTATION)
	9X-4385	[1]	PLUG AS-CONNECTOR (6-PIN)
	155-2272	[1]	PLUG AS-CONNECTOR (4-PIN)
5.	061-6665	[2]	BOLT (1/2-13X1.25-IN)
6.	089-7960	[1]	WASHER (5.3X25X1.6-MM THK)
7.	160-8500 M	[4]	NUT (M8X1.25-THD)
8.	186-0359	[1]	CLIP
9.	188-9644 M	[4]	SCREW-FLAT HEAD (M8X1.25X25-MM)
10.	211-9032	[4]	WASHER-HARD (8.8X13X2-MM THK)
11.	251-2383	[1]	BRACKET
12.	4K-8302	[4]	CLIP (LOOP)
13.	5C-2890 M	[1]	NUT (M6X1-THD)
14.	8T-4244 M	[1]	NUT (M12X1.75-THD)
15.	7Y-0589 M	[1]	BOLT (M12X1.75X90-MM)
16.	8T-0326 M	[1]	BOLT (M5X0.8X25-MM)
17.	8T-4121	[8]	WASHER-HARD (11X21X2.5-MM THK)
18.	8T-4133 M	[2]	NUT (M10X1.5-THD)
19.	8T-4191 M	[4]	BOLT (M10X1.5X16-MM)
20.	8T-4195 M	[2]	BOLT (M10X1.5X30-MM)
21.	8T-4223	[1]	WASHER-HARD (13.5X25.5X3-MM THK)
22.	8X-5489	[2]	SLEEVE
23.	9X-2537 M	[4]	BOLT-SOCKET HEAD (M6X1X70-MM)
24.	9X-8256	[5]	WASHER (6.6X12X2-MM THK)
	M		METRIC PART

Information:

ELECTRICAL AND STARTING SYSTEM

WIRING GP

Engine News

270-5051 Repair Kit (Electrical Connectors) Available for Repairs to Wiring Harnesses with Ampseal 16 and A4E 2 Connectors {0709, 1408}
2006/03/20

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2010/05/13

Special Instruction

Cross-Reference for Electrical Connectors {7553}
Cross-Reference for Electrical Connectors {7553}

Circuit Breaker Harness Assembly {1420}
Circuit Breaker Harness Assembly {1420}

Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}
Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}

Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}
Installation and Operation of the Exhaust Monitor Used in All Diesel Particulate Filter (DPF) Retrofit Emissions Applications{1091, 1408, 7490, 7498}

Tool Operating Manual

Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}
Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}

Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}

Reuse And Salvage Guidelines

Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}

Testing and Adjusting

Electric Starting System - Test
3176C and 3196 Engines for Caterpillar Built Machines

Troubleshooting

CID 0168 FMI 02 System Voltage intermittent/erratic
3176C and 3196 Engines for Caterpillar Built Machines

CID 0168 FMI 01 System Voltage Low
3176C and 3196 Engines for Caterpillar Built Machines

CID 0168 FMI 00 System Voltage High
3176C and 3196 Engines for Caterpillar Built Machines

CID 0545 FMI 05 Ether Start Relay open/short to +batt
3176C and 3196 Engines for Caterpillar Built Machines

CID 0291 FMI 05 Engine Cooling Fan Solenoid open circuit
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

CID 0291 FMI 06 Engine Cooling Fan Solenoid short to ground
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

CID 0545 FMI 06 Ether Start Relay short to ground
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

Sensors and Electrical Connectors
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

Electrical Connectors - Inspect
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0100 FMI 03 Engine Oil Pressure open/short to +batt
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

CID 0100 FMI 04 Engine Oil Pressure short to ground
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader

CID 0172 FMI 03 Intake Manifold Air Temp open/short to +batt
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0172 FMI 04 Intake Manifold Air Temp short to ground
3176C and 3196 Engines for Caterpillar Built Machines

CID 0174 FMI 03 Fuel Temperature open/short to +batt
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

CID 0174 FMI 04 Fuel Temperature short to ground
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
3176C and 3196 Engines for Caterpillar Built Machines

CID 0273 FMI 03 Turbo Outlet Pressure open/short to +batt
3176C and 3196 Engines for Caterpillar Built Machines

CID 0273 FMI 04 Turbo Outlet Pressure short to ground
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

CID 0274 FMI 03 Atmospheric Pressure open/short to +batt
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

CID 0274 FMI 04 Atmospheric Pressure short to ground
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader

Engine Pressure Sensor Open or Short Circuit - Test
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0041 FMI 04 8 Volt DC Supply short to ground
3176C and 3196 Engines for Caterpillar Built Machines

CID 0248 FMI 09 Cat Data Link not communicating
3176C and 3196 Engines for Caterpillar Built Machines

CID 0283 FMI 05 Filter Restrict Lamp open/short to +batt
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

Air Filter Restriction Lamp - Test
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

Engine Shutdown Switch Circuit - Test
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

Throttle Position Sensor Circuit - Test
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader

Digital Sensor Supply Circuit - Test
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader

Engine Cooling Fan Bypass Solenoid Circuit - Test
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 1076 FMI 05 Engine Cooling Fan Bypass Solenoid open circuit
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 1076 FMI 06 Engine Cooling Fan Bypass Solenoid short to ground
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0091 FMI 08 Throttle Position signal abnormal
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0283 FMI 06 Filter Restrict Lamp short to ground
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0548 FMI 06 Throttle Lock Lamp short
3176C and 3196 Engines for Caterpillar Built Machines

CID 0548 FMI 05 Throttle Lock Lamp open circuit
3176C and 3196 Engines for Caterpillar Built Machines

CID 0094 FMI 03 Fuel Pressure open/short to +batt
3176C and 3196 Engines for Caterpillar Built Machines

CID 0094 FMI 04 Fuel Pressure short to ground
3176C and 3196 Engines for Caterpillar Built Machines

CID 0110 FMI 03 Engine Coolant Temperature open/short to +batt
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0110 FMI 04 Engine Coolant Temperature short to ground
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader

CID 0267 FMI 02 Incorrect Engine Shutdown Switch inputs
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0600 FMI 03 Hydraulic Oil Temperature open/short to +batt
3176C and 3196 Engines for Caterpillar Built Machines

CID 0600 FMI 04 Hydraulic Oil Temperature short to ground
3176C and 3196 Engines for Caterpillar Built Machines

CID 0041 FMI 03 8 Volt DC Supply short to +batt
3176C and 3196 Engines for Caterpillar Built Machines

CID 0190 FMI 11 Engine Speed Sensor mechanical failure
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0342 FMI 11 Secondary Engine Speed Sensor mechanical failure
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

Sensors and Electrical Connectors
3176C and 3196 Engines for Caterpillar Built Machines

Engine Pressure Sensor Open or Short Circuit - Test
3176C and 3196 Engines for Caterpillar Built Machines

5 Volt Engine Pressure Sensor Supply Circuit - Test
3176C and 3196 Engines for Caterpillar Built Machines

Throttle Position Sensor Circuit - Test
3176C and 3196 Engines for Caterpillar Built Machines

Digital Sensor Supply Circuit - Test
3176C and 3196 Engines for Caterpillar Built Machines

Electrical Power Supply Circuit - Test
3176C and 3196 Engines for Caterpillar Built Machines

CID 0788 FMI 02 Loss of Engine Retarder Selector Switch Signal
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

Compression Brake Lamp Circuit - Test
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 1586 FMI 05 Retarder Indicator Lamp open circuit
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 1586 FMI 06 Retarder Indicator Lamp short to ground
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0290 FMI 03 Engine Fan Pump Pressure open/short to +batt
3176C and 3196 Engines for Caterpillar Built Machines

CID 0290 FMI 04 Engine Fan Pump Pressure short to ground
3176C and 3196 Engines for Caterpillar Built Machines

Cat Data Link Circuit - Test
3176C and 3196 Engines for Caterpillar Built Machines

Engine Fan Control Solenoid Circuit - Test
3176C and 3196 Engines for Caterpillar Built Machines

Throttle Lock Switch Circuit - Test
3176C and 3196 Engines for Caterpillar Built Machines

Throttle Lock Lamp Circuit - Test
3176C and 3196 Engines for Caterpillar Built Machines

Sensors and Electrical Connectors
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

Digital Sensor Supply Circuit - Test
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

Engine Pressure Sensor Open or Short Circuit - Test
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader

Throttle Position Sensor Circuit - Test
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

CID 1582 FMI 03 Trans Lube Oil Temp Sensor open/short to +batt
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

CID 1582 FMI 04 Trans Lube Oil Temp Sensor short to ground
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

CID 1589 FMI 03 Turbo Inlet Air Pressure Sensor open/shrt to +bat
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader

Air Filter Restriction Lamp - Test
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

Engine Shutdown Switch Circuit - Test
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

Engine Fan Control Solenoid Circuit - Test
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

CID 0190 FMI 02 Loss of Engine Speed Signal
3176C and 3196 Engines for Caterpillar Built Machines

Engine Fan Control Solenoid Circuit - Test
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

Sensors and Electrical Connectors
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader

Engine Shutdown Switch Circuit - Test
3176C and 3196 Engines for Caterpillar Built Machines

CID 0275 FMI 03 Right Turbo Inlet Pressure open/short to +batt
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0275 FMI 04 Right Turbo Inlet Pressure short to ground
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0485 FMI 05 Engine Fan Rev Solenoid open circuit
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader

CID 0485 FMI 06 Engine Fan Rev Solenoid short to ground
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader

Engine Fan Reversing Solenoid Circuit - Test
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader

CID 0342 FMI 02 Loss of Secondary Engine Speed signal
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0486 FMI 02 Engine Fan Reverse Switch inputs incorrect
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader

Engine Speed/Timing Sensor Circuit - Test
3176C and 3196 Engines for Caterpillar Built Machines

CID 0485 FMI 03 Engine Fan Rev Solenoid short to +batt
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

CID 0485 FMI 04 Engine Fan Rev Solenoid short to ground
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

Engine Wiring Information
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
3176C, 3196 and 3406E Engines for 725, 730, 735, 740, and 740 Ejector Articulated Trucks

CID 1589 FMI 04 Turbo Inlet Air Pressure Sensor short to ground
3176C, 3196 and 3406E Engines for Caterpillar Built Machines

Engine Shutdown Switch Circuit - Test
3176C, 3406E and 3456 Engines for 816F, 826G Series II, and 836G Landfill Compactors, 815F and 825G Series II Soil Compactors, 814F, 824G Series II, and 834G Wheel Dozers, and for the 988G Wheel Loader

Service Magazine

Dielectric Grease Should Not Be Used in Electrical Connectors {1408, 7553}
2012/05/04

Service of the Machined Terminals and the Stamped and Formed Terminals {7553}
2006/11/13

Updated Instruction For The Bypass Harness {0785, 1408}
2008/03/17

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2010/05/12

Striped Wire Is Replaced With Improved Ink Jet Identification for Legacy (Parts Service) Wire harnesses {1408}
2012/06/08

Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553, 7556}
2012/05/08

Information On Battery Cables and Wire Assemblies for Assembling at Dealer Site {4459}
2012/09/21