WORK TOOLS
BLADE GPGROUND ENGAGING TOOLS (G.E.T.)
SERVICE EQUIPMENT AND SUPPLIES
CHARTS & FILMSLINES GP-DIAGNOSTIC
WORK TOOLS
BLADE GP
#SEBP67180740
418-4611: BLADE GP-STRAIGHT
418-4611 BLADE GP-STRAIGHT -SEMI-UNIVERSAL WITH PUSH PLATE
S/N RWB1-UP
S/N RWB1-UP
For full view, you need register
Parts for your 824K WHEEL DOZER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 4T-8799 | [3] | SOLE | |
| 2. | 6J-6604 | [1] | PIN | |
| 3. | 6J-8570 | [1] | RETAINER | |
| 4. | 7K-9221 | [6] | WASHER | |
| 5. | 107-8565 Y | [1] | EDGE GP-BIT & CUTTING | |
| 6. | Y | [1] | BLADE AS (SEMI-UNIVERSAL WITH PUSH PLATE) | |
| 7. | 2J-3505 | [15] | NUT-FULL (7/8-9-THD) | |
| 8. | 5P-8249 | [15] | WASHER-HARD (24X41.5X4-MM THK) | |
| 9. | 6F-0196 | [15] | BOLT-PLOW (7/8-9X2.75-IN) | |
| 10. | 8T-5460 M | [2] | BOLT (M20X2.5X40-MM) | |
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP67180741
398-1101: BLADE GP-UNIVERSAL
398-1101 BLADE GP-UNIVERSAL
S/N RWB1-UP
S/N RWB1-UP
For full view, you need register
Parts for your 824K WHEEL DOZER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 2J-3507 | [38] | NUT-FULL (1-8-THD) | |
| 2. | 3K-9770 | [14] | NUT-FULL (1-1/4-7-THD) | |
| 3. | 3R-2299 | [14] | BOLT (1-1/4-7X3-IN) | |
| 4. | 4J-9208 | [38] | BOLT-PLOW (1-8X3.5-IN) | |
| 5. | 4K-0684 | [14] | WASHER-HARD (34X55X6-MM THK) | |
| 6. | 4T-2986 | [2] | EDGE-CUTTING | |
| 7. | 4T-2988 | [2] | EDGE-CUTTING | |
| 8. | 4T-8089 | [1] | BIT-END (RH) | |
| 9. | 4T-8090 | [1] | BIT-END (LH) | |
| 10. | 5P-8250 | [38] | WASHER (28X49X5-MM THK) | |
| 11. | 6J-6604 | [1] | PIN | |
| 12. | 6J-8570 | [1] | RETAINER | |
| 13. | 8T-4123 | [2] | WASHER (22X35X3.5-MM THK) | |
| 14. | 8T-5460 M | [2] | BOLT (M20X2.5X40-MM) | |
| 15. | 135-9668 | [2] | SOLE | |
| 17. | 312-5694 | [1] | SETSCREW (1/4-20X0.25-IN) | |
| 18. | Y | [1] | BLADE AS-UNIVERSAL | |
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP67180742
418-4579: BLADE GP-UNIVERSAL
418-4579 BLADE GP-UNIVERSAL -EXTREME SERVICE
S/N RWB1-UP
8.1-CU M (10.6-CU YD)
Type 1
FOR USE WITH @@@@@418-4580@@@@@, @@@@@418-4581@@@@@
S/N RWB1-UP
8.1-CU M (10.6-CU YD)
Type 1
FOR USE WITH @@@@@418-4580@@@@@, @@@@@418-4581@@@@@
For full view, you need register
Parts for your 824K WHEEL DOZER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 2J-3507 | [38] | NUT-FULL (1-8-THD) | |
| 2. | 3K-9770 | [14] | NUT-FULL (1-1/4-7-THD) | |
| 3. | 3R-2299 | [14] | BOLT (1-1/4-7X3-IN) | |
| 4. | 4J-9208 | [38] | BOLT-PLOW (1-8X3.5-IN) | |
| 5. | 4K-0684 | [14] | WASHER-HARD (34X55X6-MM THK) | |
| 6. | 4T-2986 | [2] | EDGE-CUTTING | |
| 7. | 4T-2988 | [2] | EDGE-CUTTING | |
| 8. | 4T-8089 | [1] | BIT-END (RH) | |
| 9. | 4T-8090 | [1] | BIT-END (LH) | |
| 10. | 5P-8245 | [8] | WASHER-HARD (13.5X25.5X3-MM THK) | |
| 11. | 5P-8250 | [38] | WASHER (28X49X5-MM THK) | |
| 12. | 6J-6604 | [1] | PIN | |
| 13. | 6J-8570 | [1] | RETAINER | |
| 14. | 8T-4123 | [2] | WASHER (22X35X3.5-MM THK) | |
| 15. | 8T-4139 M | [8] | BOLT (M12X1.75X30-MM) | |
| 16. | 8T-5460 M | [2] | BOLT (M20X2.5X40-MM) | |
| 17. | 135-9668 | [2] | SOLE | |
| 18. | 137-4234 | [1] | PLATE-IDENTIFICATION (WORK TOOL) | |
| 20. | 426-4209 Y | [1] | BLADE AS | |
| 21. | 312-5694 | [1] | SETSCREW (1/4-20X0.25-IN) | |
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP67180743
418-4579: BLADE GP-UNIVERSAL
418-4579 BLADE GP-UNIVERSAL -EXTREME SERVICE
S/N RWB1-UP
8.1-CU M (10.6-CU YD)
Type 2
FOR USE WITH @@@@@418-4580@@@@@, @@@@@418-4581@@@@@
S/N RWB1-UP
8.1-CU M (10.6-CU YD)
Type 2
FOR USE WITH @@@@@418-4580@@@@@, @@@@@418-4581@@@@@
For full view, you need register
Parts for your 824K WHEEL DOZER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 2J-3507 | [38] | NUT-FULL (1-8-THD) | |
| 2. | 3K-9770 | [14] | NUT-FULL (1-1/4-7-THD) | |
| 3. | 3R-2299 | [14] | BOLT (1-1/4-7X3-IN) | |
| 4. | 4J-9208 | [38] | BOLT-PLOW (1-8X3.5-IN) | |
| 5. | 4K-0684 | [14] | WASHER-HARD (34X55X6-MM THK) | |
| 6. | 4T-2986 | [2] | EDGE-CUTTING | |
| 7. | 4T-2988 | [2] | EDGE-CUTTING | |
| 8. | 4T-8089 | [1] | BIT-END (RH) | |
| 9. | 4T-8090 | [1] | BIT-END (LH) | |
| 11. | 5P-8250 | [38] | WASHER (28X49X5-MM THK) | |
| 12. | 6J-6604 | [1] | PIN | |
| 13. | 6J-8570 | [1] | RETAINER | |
| 14. | 8T-4123 | [2] | WASHER (22X35X3.5-MM THK) | |
| 16. | 8T-5460 M | [2] | BOLT (M20X2.5X40-MM) | |
| 17. | 135-9668 | [2] | SOLE | |
| 18. | 137-4234 | [1] | PLATE-IDENTIFICATION (WORK TOOL) | |
| 20. | 426-4209 Y | [1] | BLADE AS | |
| 21. | 312-5694 | [1] | SETSCREW (1/4-20X0.25-IN) | |
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP67180744
426-0896: BLADE GP-UNIVERSAL
426-0896 BLADE GP-UNIVERSAL -UNIVERSAL
S/N RWB1-UP
16.2-CU M (21.2-CU YD)
FOR USE WITH COMPACTOR-POWER/LANDFILL SALES MODEL 824K
S/N RWB1-UP
16.2-CU M (21.2-CU YD)
FOR USE WITH COMPACTOR-POWER/LANDFILL SALES MODEL 824K
For full view, you need register
Parts for your 824K WHEEL DOZER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 1D-4610 | [4] | BOLT (3/4-10X3.25-IN) | |
| 2. | 2J-3505 | [54] | NUT-FULL (7/8-9-THD) | |
| 3. | 2J-3506 | [4] | NUT-FULL (3/4-10-THD) | |
| 4. | 3B-4629 | [4] | PIN-COTTER | |
| 5. | 4T-2992 | [3] | EDGE-CUTTING | |
| 6. | 4T-8799 | [3] | SOLE | |
| 7. | 5B-0230 | [4] | PIN-CLEVIS | |
| 8. | 5J-4772 | [21] | BOLT-PLOW | |
| 9. | 5P-8248 | [4] | WASHER-HARD (20X36.5X3.5-MM THK) | |
| 10. | 5P-8249 | [54] | WASHER-HARD (24X41.5X4-MM THK) | |
| 11. | 6F-0196 | [33] | BOLT-PLOW (7/8-9X2.75-IN) | |
| 12. | 6J-6604 | [1] | PIN | |
| 13. | 6J-8570 | [1] | RETAINER | |
| 14. | 8T-4123 | [2] | WASHER (22X35X3.5-MM THK) | |
| 15. | 8T-5460 M | [2] | BOLT (M20X2.5X40-MM) | |
| 16. | 137-4234 | [1] | PLATE-IDENTIFICATION (WORK TOOL) | |
| 17. | 171-4808 | [2] | BASE AS | |
| 18. | 171-4809 | [2] | SHOE AS | |
| 19. | 312-5694 | [1] | SETSCREW (1/4-20X0.25-IN) | |
| 20. | 329-1155 | [1] | EDGE-CUTTING | |
| 21. | 329-1156 | [1] | EDGE-CUTTING | |
| 22. | 329-1157 | [2] | EDGE-CUTTING | |
| 23. | 432-7420 Y | [1] | BLADE AS-UNIVERSAL | |
| M | METRIC PART | |||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP67180745
107-8565: EDGE GP-BIT & CUTTING
107-8565 EDGE GP-BIT & CUTTING
S/N RWB1-UP
PART OF 397-7886, 418-4611 BLADE GP-STRAIGHT
S/N RWB1-UP
PART OF 397-7886, 418-4611 BLADE GP-STRAIGHT
For full view, you need register
#SEBP67180746
376-5205: FILM GP
For full view, you need register
Parts for your 824K WHEEL DOZER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 376-5206 Y | [1] | FILM GP | ||
| 128-8007 | [1] | FILM-IDENTIFICATION (GREASE) | ||
| (ON FRONT OF ENGINE END FRAME TO LEFT OF GREASE FITTINGS) | ||||
| 271-2161 | [1] | FILM-IDENTIFICATION (COOLANT LEVEL) | ||
| (ON LH SIDE OF COOLANT LEVEL SIGHT GAUGE) | ||||
| 376-5014 | [1] | FILM-IDENTIFICATION (GREASE POINTS) | ||
| (ON RH REAR OF NON ENGINE END FRAME TO LEFT OF GREASE FITTINGS) | ||||
| 376-5015 | [1] | FILM-IDENTIFICATION (PORT) | ||
| (ON LH SIDE OF DIAGNOSTIC PORT PLATE) | ||||
| 376-5016 | [1] | FILM-IDENTIFICATION (HYDRAULIC OIL LEVEL) | ||
| (ON LH SIDE OF HYDRAULIC TANK COVER NEAR SIGHT GAUGE) | ||||
| 376-5018 | [1] | FILM-IDENTIFICATION (TRANSMISSION OIL LEVEL) | ||
| (ON PLATE LH OF TRANSMISSION SIGHT GAUGE) | ||||
| 1P-2807 | [2] | FILM-IDENTIFICATION (LIFT EYE LOCATION) | ||
| (ON REAR LIFT EYES) | ||||
| 7X-3229 | [2] | FILM-IDENTIFICATION (LIFT EYE, TIE-DOWN LOCATION) | ||
| (ONE ON EACH FRONT LIFT & TIE DOWN EYE) | ||||
| 118-1225 | [1] | FILM-IDENTIFICATION (TRANSMISSION TANK FILL CAP) | ||
| (ON TRANSMISSION OIL FILL CAP) | ||||
| 190-5386 | [2] | FILM-IDENTIFICATION (ROUND RED REFLECTIVE) | ||
| (ON REAR OUTSIDE SURFACE OF BUMPER. 760-MM FROM CENTER, CENTERED VERTICALLY ON FLAT SURFACE. ONE ON RIGHT, ONE ON LEFT) | ||||
| 146-6747 | [1] | FILM-INFORMATION (24-VOLT) | ||
| (ON ELECTRICAL PANEL TO RIGHT OF REMOTE JUMP START TERMINAL) | ||||
| 235-8026 | [1] | FILM-INFORMATION (TRANSMISSION OIL LEVEL) | ||
| (ON TRANSMISSION FILL ACCESS DOOR, LH SIDE) | ||||
| 350-0684 | [1] | FILM-INFORMATION (ENGINE OIL, READ OMM) | ||
| (ON LH REAR HOOD POST ABOVE HIGH SPEED OIL CHANGE RECEIVER) | ||||
| 425-8663 | [1] | FILM-INFORMATION (BELT ROUTING) | ||
| (ON LOWER RH COVER ON SOUND WALL) | ||||
| 134-7258 | [1] | FILM-INFORMATION (EXTENDED LIFE COOLANT) | ||
| (ON UNDERSIDE OF RADIATOR FILL CAP ACCESS DOOR) | ||||
| 124-2456 | [4] | FILM-INSTRUCTION (NO STEP) | ||
| 1-(ON TOP OF HYDRAULIC TANK COVER) | ||||
| 2-(ON PLATE WITH NO TREAD PLATE NEXT TO LH & RH STAIRS) | ||||
| 1-(ON REAR BUMPER BEHIND RADIATOR GUARD) | ||||
| 281-7268 | [1] | FILM-INSTRUCTION (ENGINE SHUTDOWN) | ||
| (ON LH BUMPER ON RECESSED DOOR BELOW LATCH) | ||||
| 225-4257 | [2] | FILM-WARNING (HOT FLUID UNDER PRESS) | ||
| 1-(ON UNDERSIDE OF RADIATOR FILL CAP ACCESS DOOR) | ||||
| 1-(ON HYDRAULIC TANK FILTER COVER) | ||||
| 8T-7038 | [1] | FILM-WARNING (DO NOT LIFT) | ||
| (NEAR DRAW BAR PIN) | ||||
| 225-0312 | [1] | FILM-WARNING (JUMP START, READ OMM, INTL) | ||
| (ON UNDERSIDE OF BATTERY BOX DOOR) | ||||
| 226-1240 | [2] | FILM-WARNING (CRUSH HAZARD, STAY BACK, INTL) | ||
| (ONE ON BOTH SIDES OF FACE OF NEEF) | ||||
| 226-1274 | [1] | FILM-WARNING (CRUSH HAZARD, READ OMM, INTL) | ||
| (ON SIDE OF NEEF, SAME SIDE AS SAFETY BAR) | ||||
| 227-7391 | [1] | FILM-WARNING (SEAT BELT, INTERNATIONAL) | ||
| (SEAT BELT FILM ON THE LEFT FRONT ROPS TUBE) | ||||
| 228-2616 | [1] | FILM-WARNING (UNIVERSAL, READ OMM) | ||
| (ON CAB ON LEFT FRONT ROPS TUBE) | ||||
| 236-7227 | [1] | FILM-WARNING (PARKING BRAKE, INTERNATIONAL) | ||
| (ON CENTER OF RETAINING PLATE ON PARKING BRAKE GROUP) | ||||
| 237-6256 | [1] | FILM-WARNING (FAN) | ||
| (ON PLATE ON GUARD ASSEMBLY, ONE ON EACH PLATE) | ||||
| 314-3986 | [2] | FILM-WARNING (FALLING HAZARD, READ OMM) | ||
| (SEE OMM/FALL HAZARD FILM ON FRONT FENDER NEAR TOP-ONE ON EACH FENDER) | ||||
| 358-6729 | [1] | FILM-WARNING (DOWNGRADE HAULING, READ OMM) | ||
| (ON CAB ON FRONT LEFT ROPS TUBE CONCEALED PIN) | ||||
| 239-6986 | [1] | PLATE-SERIAL NUMBER (MACHINE) | ||
| (PLATE 60-MM FORWARD & 80-MM DOWN ON LH LOADER FRAME SIDE PLATE) | ||||
| (FOR CONCEALED PIN LOCATION REFER TO CHART LOCATION) | ||||
| 3N-3790 | [1] | PLATE-SERIAL NUMBER (ENGINE) | ||
| (ON RIGHT SIDE OF REAR CYLINDER BLOCK) | ||||
| Y | SEPARATE ILLUSTRATION | |||
#SEBP67180747
376-5206: FILM GP
For full view, you need register
Parts for your 824K WHEEL DOZER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 376-5102 | [1] | FILM-IDENTIFICATION (CAT)(LH) | |
| 2. | 201-8083 | [1] | FILM-IDENTIFICATION (CAT)(REAR) | |
| 3. | 376-5207 | [1] | FILM-IDENTIFICATION (824K, LH) | |
| 4. | 376-5208 | [1] | FILM-IDENTIFICATION (824K, RH) | |
| 5. | 376-5002 | [1] | FILM-IDENTIFICATION (CAT)(RH) | |
| 6. | 376-5202 | [2] | FILM-IDENTIFICATION (SIDE) |
#SEBP67180748
383-2185: FILM GP
For full view, you need register
Parts for your 824K WHEEL DOZER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 201-2733 | [2] | FILM-INFORMATION (INPUT/OUTPUT) | |
| 2. | 219-0305 | [1] | FILM-WARNING (NO WELD, NO DRILL, READ OMM) | |
| 3. | 224-1943 | [1] | FILM-INSTRUCTION (ALTERNATE EXIT, REMOVE WINDOW) | |
| 4. | 430-3908 | [1] | FILM-IDENTIFICATION (FUSE PANEL) | |
| 5. | 439-5313 | [1] | FILM-ROPS (ROPS, FOPS, READ OMM) | |
| 6. | 236-7230 | [1] | TAG-WARNING (STEERING FRAME LOCK) | |
| 7. | 299-7880 | [1] | FILM-INSTRUCTION (NO STEP) | |
| 8. | 345-0351 | [1] | FILM-IDENTIFICATION (IGNITION SWITCH) | |
| 9. | [1] | FILM-IDENTIFICATION (WIPER) | ||
| 10. | 383-2159 | [1] | FILM-IDENTIFICATION (CIRCUIT BREAKER) | |
| 11. | [1] | FILM-INSTRUCTION (AIR CONDITIONER, READ MAN) | ||
| 12. | 430-3907 | [1] | FILM-IDENTIFICATION (FUSE PANEL) | |
| 13. | 299-5778 | [1] | FILM-WARNING (FALL HAZARD, LANYARD, READ OMM) | |
#SEBP67180749
441-3333: LINES GP-DIAGNOSTIC
For full view, you need register
Parts for your 824K WHEEL DOZER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 7K-1181 | [4] | STRAP-CABLE | |
| 2. | 124-3019 | [1] | BRACKET AS | |
| 3. | 162-9728 | [1] | BRACKET AS | |
| 4. | 296-5780 | [3] | GROMMET | |
| 5. | 441-3331 | [1] | BRACKET | |
| 6. | 441-3334 | [1] | HOSE AS | |
| 7. | 441-3335 | [1] | HOSE AS | |
| 8. | 441-3336 | [1] | HOSE AS | |
| 9. | 441-3337 | [1] | HOSE AS | |
| 10. | 441-3338 | [1] | HOSE AS | |
| 11. | 441-3339 | [1] | HOSE AS | |
| 12. | 441-3340 | [1] | HOSE AS | |
| 13. | 441-3341 | [1] | HOSE AS | |
| 14. | 441-3342 | [1] | HOSE AS | |
| 15. | 441-3343 | [1] | HOSE AS | |
| 16. | 441-3344 | [1] | HOSE AS | |
| 17. | 441-3345 | [1] | HOSE AS | |
| 18. | 101-3129 M | [2] | STUD (M10X1.5-THD) | |
| 19. | 133-6934 | [1] | SPACER (11X20X25-MM THK) | |
| 20. | 148-8325 | [1] | CONNECTOR AS | |
| 3J-1907 | [1] | SEAL-O-RING | ||
| 4J-5477 | [1] | SEAL-O-RING | ||
| 6V-8641 | [1] | CONNECTOR | ||
| 21. | 148-8351 | [2] | ELBOW AS | |
| (EACH INCLUDES) | ||||
| 4J-5477 | [1] | SEAL-O-RING | ||
| 6V-9849 | [1] | ELBOW | ||
| 22. | 148-8368 | [5] | ELBOW AS | |
| (EACH INCLUDES) | ||||
| 3J-1907 | [1] | SEAL-O-RING | ||
| 4J-5477 | [1] | SEAL-O-RING | ||
| 6V-8627 | [1] | ELBOW | ||
| 23. | 148-8369 | [1] | ELBOW AS | |
| 3J-7354 | [1] | SEAL-O-RING | ||
| 4J-5477 | [1] | SEAL-O-RING | ||
| 6V-8628 | [1] | ELBOW | ||
| 24. | 164-5567 | [12] | COUPLER AS-QUICK DISCONNECT (MALE) | |
| (EACH INCLUDES) | ||||
| 6V-3965 | [1] | FITTING (QUICK DISCONNECT) | ||
| 214-7568 | [1] | SEAL-O-RING | ||
| 25. | 169-5863 | [12] | ADAPTER AS | |
| (EACH INCLUDES) | ||||
| 4J-5477 | [1] | SEAL-O-RING | ||
| 7X-7945 | [1] | ADAPTER (9/16-18-THD) | ||
| 26. | 187-2120 | [1] | ELBOW AS | |
| 4J-5477 | [1] | SEAL-O-RING | ||
| 8C-8408 | [1] | ELBOW | ||
| 27. | 1S-0724 | [1] | CLIP | |
| 28. | 1V-7753 | [1] | SPACER (0.546X0.841X1.75-IN THK) | |
| 29. | 204-1611 | [6] | STRAP (DUAL) | |
| 30. | 204-2281 | [3] | STRAP-CABLE | |
| 31. | 204-8000 | [3] | MOUNTING-CABLE TIE | |
| 32. | 2P-1279 | [12] | LOCKNUT (9/16-18-THD) | |
| 33. | 335-3982 | [1] | ELBOW AS | |
| 6V-8627 | [1] | ELBOW | ||
| 214-7568 | [1] | SEAL-O-RING | ||
| 228-7088 | [1] | SEAL-O-RING | ||
| 34. | 344-5675 M | [8] | NUT (M10X1.5-THD) | |
| 35. | 352-3964 | [1] | CLIP (LADDER)(LADDER) | |
| 36. | 4D-7388 | [1] | CLIP (LOOP)(LOOP) | |
| 37. | 4D-8123 | [1] | CLIP (LOOP) | |
| 38. | 4P-7581 | [2] | CLIP (LADDER)(LADDER) | |
| 39. | 4S-1962 | [1] | CLIP (LOOP)(LOOP) | |
| 40. | 4S-4455 | [1] | CLIP | |
| 41. | 5P-9085 | [5] | CLIP (LOOP)(LOOP) | |
| 42. | 6V-0852 | [12] | CAP-DUST | |
| 43. | 7B-7210 | [4] | PIN | |
| 44. | 7S-4244 | [3] | CLIP | |
| 45. | 7X-7729 | [7] | WASHER (11X25X3-MM THK) | |
| 46. | 8S-8820 | [1] | CLIP | |
| 47. | 8T-4121 | [12] | WASHER-HARD (11X21X2.5-MM THK) | |
| 48. | 8T-4136 M | [4] | BOLT (M10X1.5X25-MM) | |
| 49. | 8T-4178 M | [1] | BOLT (M10X1.5X90-MM) | |
| 50. | 8T-4195 M | [3] | BOLT (M10X1.5X30-MM) | |
| 51. | 8T-4196 M | [2] | BOLT (M10X1.5X35-MM) | |
| 52. | 8T-6466 M | [1] | BOLT (M10X1.5X60-MM) | |
| 53. | 7I-1024 E | GUARD-HOSE (44-CM) | ||
| E | ORDER BY THE CENTIMETER | |||
| M | METRIC PART | |||
