4Z9018 SHANK AS-RIPPER Caterpillar parts
D9R, D9T
Rating:
Alternative (cross code) number:
CA4Z9018
4Z-9018
4Z9018
CA4Z9018
4Z-9018
4Z9018
Weight: 1150 pounds 521 kg.
TRACK-TYPE TRACTOR,
Number on catalog scheme:
4
For full view, you need register
Information:
Removal Procedure
Start By:
Remove the front tires and rims. Refer to Disassembly and Assembly, "Tire and Rim (Front) - Remove and Install".
Remove the front drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Front) - Remove and Install".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Put identification marks on all lines, on all hoses, on all wires and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Drain the oil from the fixed axle. Refer to Operation and Maintenance Manual, "Refill Capacities".
Illustration 1 g00841237
Disconnect hose assembly (1) from fixed axle (2) .
Disconnect harness assembly (3) .
Illustration 2 g01189541
Attach a suitable lifting device to each side of the fixed axle, as shown. The weight of the fixed axle is approximately 1134 kg (2500 lb).
Illustration 3 g00841243
Remove bolts (4) and cover (5) from each side of the fixed axle.
Remove bolts (6) and the washers.
Use the suitable lifting device to lower the fixed axle from the machine.
Start By:
Remove the front tires and rims. Refer to Disassembly and Assembly, "Tire and Rim (Front) - Remove and Install".
Remove the front drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Front) - Remove and Install".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the attachments have been lowered, oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Put identification marks on all lines, on all hoses, on all wires and on all tubes for installation purposes. Plug all lines, all hoses and all tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Drain the oil from the fixed axle. Refer to Operation and Maintenance Manual, "Refill Capacities".
Illustration 1 g00841237
Disconnect hose assembly (1) from fixed axle (2) .
Disconnect harness assembly (3) .
Illustration 2 g01189541
Attach a suitable lifting device to each side of the fixed axle, as shown. The weight of the fixed axle is approximately 1134 kg (2500 lb).
Illustration 3 g00841243
Remove bolts (4) and cover (5) from each side of the fixed axle.
Remove bolts (6) and the washers.
Use the suitable lifting device to lower the fixed axle from the machine.
Caterpillar parts catalog:
Parts shank Caterpillar catalog:
D10N, D9R
D10N, D10R, D10T, D10T2, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
D9N, D9R
1380876
SHANK AS-RIPPER
D9R, D9T
D9R, D9T
1099114
SHANK AS-RIPPER
D9R, D9T
D9R, D9T
8E5348
SHANK AS-RIPPER
D9N, D9R
D9N, D9R
D9R, D9T
120B, 120G, 120H, 12E, 12F, 12G, 12H NA, 130G, 140B, 140G, 140H NA, 14E, 160G, 950
6K5704
SHANK
16
16
Caterpillar
3Y0351
SHANK
Caterpillar
Caterpillar
D7E, D7E LGP, D7G, D7G2, D7H, D7R, D7R II, D7R XR
D7G
4Z9312
SHANK AS-RIPPER
D11R, D11T
D11R, D11T
4Z8849
SHANK AS
D11R, D11T
D11R, D11T
4Z9197
SHANK-RIPPER
D11R
D11R
1099114
SHANK AS-RIPPER
D9R, D9T
D9R, D9T
1380876
SHANK AS-RIPPER
D9R, D9T
D9R, D9T
D9N, D9R